diff options
Diffstat (limited to 'arch')
36 files changed, 3450 insertions, 26 deletions
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index aef63c8e3d2..f07a4ba281b 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -126,6 +126,13 @@ config ARCH_HAS_ILOG2_U32 config ARCH_HAS_ILOG2_U64 bool +config ARCH_HAS_CPUFREQ + bool + help + Internal node to signify that the ARCH has CPUFREQ support + and that the relevant menu configurations are displayed for + it. + config GENERIC_HWEIGHT bool default y @@ -203,6 +210,7 @@ config ARCH_AAEC2000 config ARCH_INTEGRATOR bool "ARM Ltd. Integrator family" select ARM_AMBA + select ARCH_HAS_CPUFREQ select HAVE_CLK select COMMON_CLKDEV select ICST525 @@ -509,6 +517,7 @@ config ARCH_PXA bool "PXA2xx/PXA3xx-based" depends on MMU select ARCH_MTD_XIP + select ARCH_HAS_CPUFREQ select GENERIC_GPIO select HAVE_CLK select COMMON_CLKDEV @@ -551,6 +560,7 @@ config ARCH_SA1100 select ISA select ARCH_SPARSEMEM_ENABLE select ARCH_MTD_XIP + select ARCH_HAS_CPUFREQ select GENERIC_GPIO select GENERIC_TIME select GENERIC_CLOCKEVENTS @@ -563,6 +573,7 @@ config ARCH_SA1100 config ARCH_S3C2410 bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442, S3C2443" select GENERIC_GPIO + select ARCH_HAS_CPUFREQ select HAVE_CLK help Samsung S3C2410X CPU based systems, such as the Simtec Electronics @@ -573,6 +584,7 @@ config ARCH_S3C64XX bool "Samsung S3C64XX" select GENERIC_GPIO select HAVE_CLK + select ARCH_HAS_CPUFREQ help Samsung S3C64XX series based systems @@ -632,6 +644,7 @@ config ARCH_OMAP select GENERIC_GPIO select HAVE_CLK select ARCH_REQUIRE_GPIOLIB + select ARCH_HAS_CPUFREQ select GENERIC_TIME select GENERIC_CLOCKEVENTS help @@ -1241,7 +1254,7 @@ endmenu menu "CPU Power Management" -if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA || ARCH_S3C64XX) +if ARCH_HAS_CPUFREQ source "drivers/cpufreq/Kconfig" @@ -1276,6 +1289,52 @@ config CPU_FREQ_S3C64XX bool "CPUfreq support for Samsung S3C64XX CPUs" depends on CPU_FREQ && CPU_S3C6410 +config CPU_FREQ_S3C + bool + help + Internal configuration node for common cpufreq on Samsung SoC + +config CPU_FREQ_S3C24XX + bool "CPUfreq driver for Samsung S3C24XX series CPUs" + depends on ARCH_S3C2410 && CPU_FREQ && EXPERIMENTAL + select CPU_FREQ_S3C + help + This enables the CPUfreq driver for the Samsung S3C24XX family + of CPUs. + + For details, take a look at <file:Documentation/cpu-freq>. + + If in doubt, say N. + +config CPU_FREQ_S3C24XX_PLL + bool "Support CPUfreq changing of PLL frequency" + depends on CPU_FREQ_S3C24XX && EXPERIMENTAL + help + Compile in support for changing the PLL frequency from the + S3C24XX series CPUfreq driver. The PLL takes time to settle + after a frequency change, so by default it is not enabled. + + This also means that the PLL tables for the selected CPU(s) will + be built which may increase the size of the kernel image. + +config CPU_FREQ_S3C24XX_DEBUG + bool "Debug CPUfreq Samsung driver core" + depends on CPU_FREQ_S3C24XX + help + Enable s3c_freq_dbg for the Samsung S3C CPUfreq core + +config CPU_FREQ_S3C24XX_IODEBUG + bool "Debug CPUfreq Samsung driver IO timing" + depends on CPU_FREQ_S3C24XX + help + Enable s3c_freq_iodbg for the Samsung S3C CPUfreq core + +config CPU_FREQ_S3C24XX_DEBUGFS + bool "Export debugfs for CPUFreq" + depends on CPU_FREQ_S3C24XX && DEBUG_FS + help + Export status information via debugfs. + endif source "drivers/cpuidle/Kconfig" diff --git a/arch/arm/mach-s3c2410/Kconfig b/arch/arm/mach-s3c2410/Kconfig index 41bb65d5b91..d8c023d4df3 100644 --- a/arch/arm/mach-s3c2410/Kconfig +++ b/arch/arm/mach-s3c2410/Kconfig @@ -12,6 +12,7 @@ config CPU_S3C2410 select S3C2410_GPIO select CPU_LLSERIAL_S3C2410 select S3C2410_PM if PM + select S3C2410_CPUFREQ if CPU_FREQ_S3C24XX help Support for S3C2410 and S3C2410A family from the S3C24XX line of Samsung Mobile CPUs. @@ -45,6 +46,22 @@ config MACH_BAST_IDE Internal node for machines with an BAST style IDE interface +# cpu frequency scaling support + +config S3C2410_CPUFREQ + bool + depends on CPU_FREQ_S3C24XX && CPU_S3C2410 + select S3C2410_CPUFREQ_UTILS + help + CPU Frequency scaling support for S3C2410 + +config S3C2410_PLLTABLE + bool + depends on S3C2410_CPUFREQ && CPU_FREQ_S3C24XX_PLL + default y + help + Select the PLL table for the S3C2410 + menu "S3C2410 Machines" config ARCH_SMDK2410 @@ -79,6 +96,7 @@ config MACH_N30 config ARCH_BAST bool "Simtec Electronics BAST (EB2410ITX)" select CPU_S3C2410 + select S3C2410_IOTIMING if S3C2410_CPUFREQ select PM_SIMTEC if PM select SIMTEC_NOR select MACH_BAST_IDE diff --git a/arch/arm/mach-s3c2410/Makefile b/arch/arm/mach-s3c2410/Makefile index fca02f82711..2ab5ba4b266 100644 --- a/arch/arm/mach-s3c2410/Makefile +++ b/arch/arm/mach-s3c2410/Makefile @@ -15,6 +15,8 @@ obj-$(CONFIG_CPU_S3C2410_DMA) += dma.o obj-$(CONFIG_CPU_S3C2410_DMA) += dma.o obj-$(CONFIG_S3C2410_PM) += pm.o sleep.o obj-$(CONFIG_S3C2410_GPIO) += gpio.o +obj-$(CONFIG_S3C2410_CPUFREQ) += cpu-freq.o +obj-$(CONFIG_S3C2410_PLLTABLE) += pll.o # Machine support diff --git a/arch/arm/mach-s3c2410/cpu-freq.c b/arch/arm/mach-s3c2410/cpu-freq.c new file mode 100644 index 00000000000..9d1186877d0 --- /dev/null +++ b/arch/arm/mach-s3c2410/cpu-freq.c @@ -0,0 +1,159 @@ +/* linux/arch/arm/mach-s3c2410/cpu-freq.c + * + * Copyright (c) 2006,2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C2410 CPU Frequency scaling + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/cpufreq.h> +#include <linux/sysdev.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <mach/regs-clock.h> + +#include <plat/cpu.h> +#include <plat/clock.h> +#include <plat/cpu-freq-core.h> + +/* Note, 2410A has an extra mode for 1:4:4 ratio, bit 2 of CLKDIV */ + +static void s3c2410_cpufreq_setdivs(struct s3c_cpufreq_config *cfg) +{ + u32 clkdiv = 0; + + if (cfg->divs.h_divisor == 2) + clkdiv |= S3C2410_CLKDIVN_HDIVN; + + if (cfg->divs.p_divisor != cfg->divs.h_divisor) + clkdiv |= S3C2410_CLKDIVN_PDIVN; + + __raw_writel(clkdiv, S3C2410_CLKDIVN); +} + +static int s3c2410_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg) +{ + unsigned long hclk, fclk, pclk; + unsigned int hdiv, pdiv; + unsigned long hclk_max; + + fclk = cfg->freq.fclk; + hclk_max = cfg->max.hclk; + + cfg->freq.armclk = fclk; + + s3c_freq_dbg("%s: fclk is %lu, max hclk %lu\n", + __func__, fclk, hclk_max); + + hdiv = (fclk > cfg->max.hclk) ? 2 : 1; + hclk = fclk / hdiv; + + if (hclk > cfg->max.hclk) { + s3c_freq_dbg("%s: hclk too big\n", __func__); + return -EINVAL; + } + + pdiv = (hclk > cfg->max.pclk) ? 2 : 1; + pclk = hclk / pdiv; + + if (pclk > cfg->max.pclk) { + s3c_freq_dbg("%s: pclk too big\n", __func__); + return -EINVAL; + } + + pdiv *= hdiv; + + /* record the result */ + cfg->divs.p_divisor = pdiv; + cfg->divs.h_divisor = hdiv; + + return 0 ; +} + +static struct s3c_cpufreq_info s3c2410_cpufreq_info = { + .max = { + .fclk = 200000000, + .hclk = 100000000, + .pclk = 50000000, + }, + + /* transition latency is about 5ms worst-case, so + * set 10ms to be sure */ + .latency = 10000000, + + .locktime_m = 150, + .locktime_u = 150, + .locktime_bits = 12, + + .need_pll = 1, + + .name = "s3c2410", + .calc_iotiming = s3c2410_iotiming_calc, + .set_iotiming = s3c2410_iotiming_set, + .get_iotiming = s3c2410_iotiming_get, + .resume_clocks = s3c2410_setup_clocks, + + .set_fvco = s3c2410_set_fvco, + .set_refresh = s3c2410_cpufreq_setrefresh, + .set_divs = s3c2410_cpufreq_setdivs, + .calc_divs = s3c2410_cpufreq_calcdivs, + + .debug_io_show = s3c_cpufreq_debugfs_call(s3c2410_iotiming_debugfs), +}; + +static int s3c2410_cpufreq_add(struct sys_device *sysdev) +{ + return s3c_cpufreq_register(&s3c2410_cpufreq_info); +} + +static struct sysdev_driver s3c2410_cpufreq_driver = { + .add = s3c2410_cpufreq_add, +}; + +static int __init s3c2410_cpufreq_init(void) +{ + return sysdev_driver_register(&s3c2410_sysclass, + &s3c2410_cpufreq_driver); +} + +arch_initcall(s3c2410_cpufreq_init); + +static int s3c2410a_cpufreq_add(struct sys_device *sysdev) +{ + /* alter the maximum freq settings for S3C2410A. If a board knows + * it only has a maximum of 200, then it should register its own + * limits. */ + + s3c2410_cpufreq_info.max.fclk = 266000000; + s3c2410_cpufreq_info.max.hclk = 133000000; + s3c2410_cpufreq_info.max.pclk = 66500000; + s3c2410_cpufreq_info.name = "s3c2410a"; + + return s3c2410_cpufreq_add(sysdev); +} + +static struct sysdev_driver s3c2410a_cpufreq_driver = { + .add = s3c2410a_cpufreq_add, +}; + +static int __init s3c2410a_cpufreq_init(void) +{ + return sysdev_driver_register(&s3c2410a_sysclass, + &s3c2410a_cpufreq_driver); +} + +arch_initcall(s3c2410a_cpufreq_init); diff --git a/arch/arm/mach-s3c2410/dma.c b/arch/arm/mach-s3c2410/dma.c index dbf96e60d99..63b753f56c6 100644 --- a/arch/arm/mach-s3c2410/dma.c +++ b/arch/arm/mach-s3c2410/dma.c @@ -164,6 +164,17 @@ static int __init s3c2410_dma_drvinit(void) } arch_initcall(s3c2410_dma_drvinit); + +static struct sysdev_driver s3c2410a_dma_driver = { + .add = s3c2410_dma_add, +}; + +static int __init s3c2410a_dma_drvinit(void) +{ + return sysdev_driver_register(&s3c2410a_sysclass, &s3c2410a_dma_driver); +} + +arch_initcall(s3c2410a_dma_drvinit); #endif #if defined(CONFIG_CPU_S3C2442) diff --git a/arch/arm/mach-s3c2410/include/mach/map.h b/arch/arm/mach-s3c2410/include/mach/map.h index e99b212cb1c..11cce097550 100644 --- a/arch/arm/mach-s3c2410/include/mach/map.h +++ b/arch/arm/mach-s3c2410/include/mach/map.h @@ -67,6 +67,13 @@ #define S3C2443_PA_HSMMC (0x4A800000) #define S3C2443_SZ_HSMMC (256) +/* S3C2412 memory and IO controls */ +#define S3C2412_PA_SSMC (0x4F000000) +#define S3C2412_VA_SSMC S3C_ADDR_CPU(0x00000000) + +#define S3C2412_PA_EBI (0x48800000) +#define S3C2412_VA_EBI S3C_ADDR_CPU(0x00010000) + /* physical addresses of all the chip-select areas */ #define S3C2410_CS0 (0x00000000) diff --git a/arch/arm/mach-s3c2410/include/mach/regs-mem.h b/arch/arm/mach-s3c2410/include/mach/regs-mem.h index 57759804e2f..7f7c5294796 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-mem.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-mem.h @@ -73,6 +73,16 @@ #define S3C2410_BWSCON_WS7 (1<<30) #define S3C2410_BWSCON_ST7 (1<<31) +/* accesor functions for getting BANK(n) configuration. (n != 0) */ + +#define S3C2410_BWSCON_GET(_bwscon, _bank) (((_bwscon) >> ((_bank) * 4)) & 0xf) + +#define S3C2410_BWSCON_DW8 (0) +#define S3C2410_BWSCON_DW16 (1) +#define S3C2410_BWSCON_DW32 (2) +#define S3C2410_BWSCON_WS (1 << 2) +#define S3C2410_BWSCON_ST (1 << 3) + /* memory set (rom, ram) */ #define S3C2410_BANKCON0 S3C2410_MEMREG(0x0004) #define S3C2410_BANKCON1 S3C2410_MEMREG(0x0008) diff --git a/arch/arm/mach-s3c2410/include/mach/regs-s3c2412-mem.h b/arch/arm/mach-s3c2410/include/mach/regs-s3c2412-mem.h index a4bf2712317..fb635251509 100644 --- a/arch/arm/mach-s3c2410/include/mach/regs-s3c2412-mem.h +++ b/arch/arm/mach-s3c2410/include/mach/regs-s3c2412-mem.h @@ -14,9 +14,11 @@ #ifndef __ASM_ARM_REGS_S3C2412_MEM #define __ASM_ARM_REGS_S3C2412_MEM -#ifndef S3C2412_MEMREG #define S3C2412_MEMREG(x) (S3C24XX_VA_MEMCTRL + (x)) -#endif +#define S3C2412_EBIREG(x) (S3C2412_VA_EBI + (x)) + +#define S3C2412_SSMCREG(x) (S3C2412_VA_SSMC + (x)) +#define S3C2412_SSMC(x, o) (S3C2412_SSMCREG((x * 0x20) + (o))) #define S3C2412_BANKCFG S3C2412_MEMREG(0x00) #define S3C2412_BANKCON1 S3C2412_MEMREG(0x04) @@ -26,4 +28,21 @@ #define S3C2412_REFRESH S3C2412_MEMREG(0x10) #define S3C2412_TIMEOUT S3C2412_MEMREG(0x14) +/* EBI control registers */ + +#define S3C2412_EBI_PR S3C2412_EBIREG(0x00) +#define S3C2412_EBI_BANKCFG S3C2412_EBIREG(0x04) + +/* SSMC control registers */ + +#define S3C2412_SSMC_BANK(x) S3C2412_SSMC(x, 0x00) +#define S3C2412_SMIDCYR(x) S3C2412_SSMC(x, 0x00) +#define S3C2412_SMBWSTRD(x) S3C2412_SSMC(x, 0x04) +#define S3C2412_SMBWSTWRR(x) S3C2412_SSMC(x, 0x08) +#define S3C2412_SMBWSTOENR(x) S3C2412_SSMC(x, 0x0C) +#define S3C2412_SMBWSTWENR(x) S3C2412_SSMC(x, 0x10) +#define S3C2412_SMBCR(x) S3C2412_SSMC(x, 0x14) +#define S3C2412_SMBSR(x) S3C2412_SSMC(x, 0x18) +#define S3C2412_SMBWSTBRDR(x) S3C2412_SSMC(x, 0x1C) + #endif /* __ASM_ARM_REGS_S3C2412_MEM */ diff --git a/arch/arm/mach-s3c2410/irq.c b/arch/arm/mach-s3c2410/irq.c index 92150399563..5e2f3533205 100644 --- a/arch/arm/mach-s3c2410/irq.c +++ b/arch/arm/mach-s3c2410/irq.c @@ -39,9 +39,22 @@ static struct sysdev_driver s3c2410_irq_driver = { .resume = s3c24xx_irq_resume, }; -static int s3c2410_irq_init(void) +static int __init s3c2410_irq_init(void) { return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_irq_driver); } arch_initcall(s3c2410_irq_init); + +static struct sysdev_driver s3c2410a_irq_driver = { + .add = s3c2410_irq_add, + .suspend = s3c24xx_irq_suspend, + .resume = s3c24xx_irq_resume, +}; + +static int __init s3c2410a_irq_init(void) +{ + return sysdev_driver_register(&s3c2410a_sysclass, &s3c2410a_irq_driver); +} + +arch_initcall(s3c2410a_irq_init); diff --git a/arch/arm/mach-s3c2410/mach-bast.c b/arch/arm/mach-s3c2410/mach-bast.c index 06670bb89ca..647c9adb018 100644 --- a/arch/arm/mach-s3c2410/mach-bast.c +++ b/arch/arm/mach-s3c2410/mach-bast.c @@ -60,6 +60,7 @@ #include <plat/clock.h> #include <plat/devs.h> #include <plat/cpu.h> +#include <plat/cpu-freq.h> #include "usb-simtec.h" #include "nor-simtec.h" @@ -601,6 +602,12 @@ static struct clk *bast_clocks[] __initdata = { &s3c24xx_uclk, }; +static struct s3c_cpufreq_board __initdata bast_cpufreq = { + .refresh = 7800, /* 7.8usec */ + .auto_io = 1, + .need_io = 1, +}; + static void __init bast_map_io(void) { /* initialise the clocks */ @@ -640,6 +647,8 @@ static void __init bast_init(void) usb_simtec_init(); nor_simtec_init(); + + s3c_cpufreq_setboard(&bast_cpufreq); } MACHINE_START(BAST, "Simtec-BAST") diff --git a/arch/arm/mach-s3c2410/pll.c b/arch/arm/mach-s3c2410/pll.c new file mode 100644 index 00000000000..f178c2fd9d8 --- /dev/null +++ b/arch/arm/mach-s3c2410/pll.c @@ -0,0 +1,95 @@ +/* arch/arm/mach-s3c2410/pll.c + * + * Copyright (c) 2006,2007 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * Vincent Sanders <vince@arm.linux.org.uk> + * + * S3C2410 CPU PLL tables + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/sysdev.h> +#include <linux/list.h> +#include <linux/clk.h> +#include <linux/err.h> + +#include <plat/cpu.h> +#include <plat/cpu-freq-core.h> + +static struct cpufreq_frequency_table pll_vals_12MHz[] = { + { .frequency = 34000000, .index = PLLVAL(82, 2, 3), }, + { .frequency = 45000000, .index = PLLVAL(82, 1, 3), }, + { .frequency = 51000000, .index = PLLVAL(161, 3, 3), }, + { .frequency = 48000000, .index = PLLVAL(120, 2, 3), }, + { .frequency = 56000000, .index = PLLVAL(142, 2, 3), }, + { .frequency = 68000000, .index = PLLVAL(82, 2, 2), }, + { .frequency = 79000000, .index = PLLVAL(71, 1, 2), }, + { .frequency = 85000000, .index = PLLVAL(105, 2, 2), }, + { .frequency = 90000000, .index = PLLVAL(112, 2, 2), }, + { .frequency = 101000000, .index = PLLVAL(127, 2, 2), }, + { .frequency = 113000000, .index = PLLVAL(105, 1, 2), }, + { .frequency = 118000000, .index = PLLVAL(150, 2, 2), }, + { .frequency = 124000000, .index = PLLVAL(116, 1, 2), }, + { .frequency = 135000000, .index = PLLVAL(82, 2, 1), }, + { .frequency = 147000000, .index = PLLVAL(90, 2, 1), }, + { .frequency = 152000000, .index = PLLVAL(68, 1, 1), }, + { .frequency = 158000000, .index = PLLVAL(71, 1, 1), }, + { .frequency = 170000000, .index = PLLVAL(77, 1, 1), }, + { .frequency = 180000000, .index = PLLVAL(82, 1, 1), }, + { .frequency = 186000000, .index = PLLVAL(85, 1, 1), }, + { .frequency = 192000000, .index = PLLVAL(88, 1, 1), }, + { .frequency = 203000000, .index = PLLVAL(161, 3, 1), }, + + /* 2410A extras */ + + { .frequency = 210000000, .index = PLLVAL(132, 2, 1), }, + { .frequency = 226000000, .index = PLLVAL(105, 1, 1), }, + { .frequency = 266000000, .index = PLLVAL(125, 1, 1), }, + { .frequency = 268000000, .index = PLLVAL(126, 1, 1), }, + { .frequency = 270000000, .index = PLLVAL(127, 1, 1), }, +}; + +static int s3c2410_plls_add(struct sys_device *dev) +{ + return s3c_plltab_register(pll_vals_12MHz, ARRAY_SIZE(pll_vals_12MHz)); +} + +static struct sysdev_driver s3c2410_plls_drv = { + .add = s3c2410_plls_add, +}; + +static int __init s3c2410_pll_init(void) +{ + return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_plls_drv); + +} + +arch_initcall(s3c2410_pll_init); + +static struct sysdev_driver s3c2410a_plls_drv = { + .add = s3c2410_plls_add, +}; + +static int __init s3c2410a_pll_init(void) +{ + return sysdev_driver_register(&s3c2410a_sysclass, &s3c2410a_plls_drv); +} + +arch_initcall(s3c2410a_pll_init); diff --git a/arch/arm/mach-s3c2410/pm.c b/arch/arm/mach-s3c2410/pm.c index 143e08a599d..966119c8efe 100644 --- a/arch/arm/mach-s3c2410/pm.c +++ b/arch/arm/mach-s3c2410/pm.c @@ -119,6 +119,18 @@ static int __init s3c2410_pm_drvinit(void) } arch_initcall(s3c2410_pm_drvinit); + +static struct sysdev_driver s3c2410a_pm_driver = { + .add = s3c2410_pm_add, + .resume = s3c2410_pm_resume, +}; + +static int __init s3c2410a_pm_drvinit(void) +{ + return sysdev_driver_register(&s3c2410a_sysclass, &s3c2410a_pm_driver); +} + +arch_initcall(s3c2410a_pm_drvinit); #endif #if defined(CONFIG_CPU_S3C2440) diff --git a/arch/arm/mach-s3c2410/s3c2410.c b/arch/arm/mach-s3c2410/s3c2410.c index feb141b1f91..91ba42f688a 100644 --- a/arch/arm/mach-s3c2410/s3c2410.c +++ b/arch/arm/mach-s3c2410/s3c2410.c @@ -105,17 +105,33 @@ void __init_or_cpufreq s3c2410_setup_clocks(void) s3c24xx_setup_clocks(fclk, hclk, pclk); } +/* fake ARMCLK for use with cpufreq, etc. */ + +static struct clk s3c2410_armclk = { + .name = "armclk", + .parent = &clk_f, + .id = -1, +}; + void __init s3c2410_init_clocks(int xtal) { s3c24xx_register_baseclocks(xtal); s3c2410_setup_clocks(); s3c2410_baseclk_add(); + s3c24xx_register_clock(&s3c2410_armclk); } struct sysdev_class s3c2410_sysclass = { .name = "s3c2410-core", }; +/* Note, we would have liked to name this s3c2410-core, but we cannot + * register two sysdev_class with the same name. + */ +struct sysdev_class s3c2410a_sysclass = { + .name = "s3c2410a-core", +}; + static struct sys_device s3c2410_sysdev = { .cls = &s3c2410_sysclass, }; @@ -133,9 +149,22 @@ static int __init s3c2410_core_init(void) core_initcall(s3c2410_core_init); +static int __init s3c2410a_core_init(void) +{ + return sysdev_class_register(&s3c2410a_sysclass); +} + +core_initcall(s3c2410a_core_init); + int __init s3c2410_init(void) { printk("S3C2410: Initialising architecture\n"); return sysdev_register(&s3c2410_sysdev); } + +int __init s3c2410a_init(void) +{ + s3c2410_sysdev.cls = &s3c2410a_sysclass; + return s3c2410_init(); +} diff --git a/arch/arm/mach-s3c2412/Kconfig b/arch/arm/mach-s3c2412/Kconfig index 63586ffd0ae..35c1bde89cf 100644 --- a/arch/arm/mach-s3c2412/Kconfig +++ b/arch/arm/mach-s3c2412/Kconfig @@ -32,6 +32,15 @@ config S3C2412_PM help Internal config node to apply S3C2412 power management +# Note, the S3C2412 IOtiming support is in plat-s3c24xx + +config S3C2412_CPUFREQ + bool + depends on CPU_FREQ_S3C24XX && CPU_S3C2412 + select S3C2412_IOTIMING + default y + help + CPU Frequency scaling support for S3C2412 and S3C2413 SoC CPUs. menu "S3C2412 Machines" diff --git a/arch/arm/mach-s3c2412/Makefile b/arch/arm/mach-s3c2412/Makefile index 20918d5dc6a..530ec46cbae 100644 --- a/arch/arm/mach-s3c2412/Makefile +++ b/arch/arm/mach-s3c2412/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_CPU_S3C2412) += clock.o obj-$(CONFIG_CPU_S3C2412) += gpio.o obj-$(CONFIG_S3C2412_DMA) += dma.o obj-$(CONFIG_S3C2412_PM) += pm.o sleep.o +obj-$(CONFIG_S3C2412_CPUFREQ) += cpu-freq.o # Machine support diff --git a/arch/arm/mach-s3c2412/cpu-freq.c b/arch/arm/mach-s3c2412/cpu-freq.c new file mode 100644 index 00000000000..eb3ea172133 --- /dev/null +++ b/arch/arm/mach-s3c2412/cpu-freq.c @@ -0,0 +1,257 @@ +/* linux/arch/arm/mach-s3c2412/cpu-freq.c + * + * Copyright 2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C2412 CPU Frequency scalling + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/cpufreq.h> +#include <linux/sysdev.h> +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <mach/regs-clock.h> +#include <mach/regs-s3c2412-mem.h> + +#include <plat/cpu.h> +#include <plat/clock.h> +#include <plat/cpu-freq-core.h> + +/* our clock resources. */ +static struct clk *xtal; +static struct clk *fclk; +static struct clk *hclk; +static struct clk *armclk; + +/* HDIV: 1, 2, 3, 4, 6, 8 */ + +static int s3c2412_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg) +{ + unsigned int hdiv, pdiv, armdiv, dvs; + unsigned long hclk, fclk, armclk, armdiv_clk; + unsigned long hclk_max; + + fclk = cfg->freq.fclk; + armclk = cfg->freq.armclk; + hclk_max = cfg->max.hclk; + + /* We can't run hclk above armclk as at the best we have to + * have armclk and hclk in dvs mode. */ + + if (hclk_max > armclk) + hclk_max = armclk; + + s3c_freq_dbg("%s: fclk=%lu, armclk=%lu, hclk_max=%lu\n", + __func__, fclk, armclk, hclk_max); + s3c_freq_dbg("%s: want f=%lu, arm=%lu, h=%lu, p=%lu\n", + __func__, cfg->freq.fclk, cfg->freq.armclk, + cfg->freq.hclk, cfg->freq.pclk); + + armdiv = fclk / armclk; + + if (armdiv < 1) + armdiv = 1; + if (armdiv > 2) + armdiv = 2; + + cfg->divs.arm_divisor = armdiv; + armdiv_clk = fclk / armdiv; + + hdiv = armdiv_clk / hclk_max; + if (hdiv < 1) + hdiv = 1; + + cfg->freq.hclk = hclk = armdiv_clk / hdiv; + + /* set dvs depending on whether we reached armclk or not. */ + cfg->divs.dvs = dvs = armclk < armdiv_clk; + + /* update the actual armclk we achieved. */ + cfg->freq.armclk = dvs ? hclk : armdiv_clk; + + s3c_freq_dbg("%s: armclk %lu, hclk %lu, armdiv %d, hdiv %d, dvs %d\n", + __func__, armclk, hclk, armdiv, hdiv, cfg->divs.dvs); + + if (hdiv > 4) + goto invalid; + + pdiv = (hclk > cfg->max.pclk) ? 2 : 1; + + if ((hclk / pdiv) > cfg->max.pclk) + pdiv++; + + cfg->freq.pclk = hclk / pdiv; + + s3c_freq_dbg("%s: pdiv %d\n", __func__, pdiv); + + if (pdiv > 2) + goto invalid; + + pdiv *= hdiv; + + /* store the result, and then return */ + + cfg->divs.h_divisor = hdiv * armdiv; + cfg->divs.p_divisor = pdiv * armdiv; + + return 0; + + invalid: + return -EINVAL; +} + +static void s3c2412_cpufreq_setdivs(struct s3c_cpufreq_config *cfg) +{ + unsigned long clkdiv; + unsigned long olddiv; + + olddiv = clkdiv = __raw_readl(S3C2410_CLKDIVN); + + /* clear off current clock info */ + + clkdiv &= ~S3C2412_CLKDIVN_ARMDIVN; + clkdiv &= ~S3C2412_CLKDIVN_HDIVN_MASK; + clkdiv &= ~S3C2412_CLKDIVN_PDIVN; + + if (cfg->divs.arm_divisor == 2) + clkdiv |= S3C2412_CLKDIVN_ARMDIVN; + + clkdiv |= ((cfg->divs.h_divisor / cfg->divs.arm_divisor) - 1); + + if (cfg->divs.p_divisor != cfg->divs.h_divisor) + clkdiv |= S3C2412_CLKDIVN_PDIVN; + + s3c_freq_dbg("%s: div %08lx => %08lx\n", __func__, olddiv, clkdiv); + __raw_writel(clkdiv, S3C2410_CLKDIVN); + + clk_set_parent(armclk, cfg->divs.dvs ? hclk : fclk); +} + +static void s3c2412_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg) +{ + struct s3c_cpufreq_board *board = cfg->board; + unsigned long refresh; + + s3c_freq_dbg("%s: refresh %u ns, hclk %lu\n", __func__, + board->refresh, cfg->freq.hclk); + + /* Reduce both the refresh time (in ns) and the frequency (in MHz) + * by 10 each to ensure that we do not overflow 32 bit numbers. This + * should work for HCLK up to 133MHz and refresh period up to 30usec. + */ + + refresh = (board->refresh / 10); + refresh *= (cfg->freq.hclk / 100); + refresh /= (1 * 1000 * 1000); /* 10^6 */ + + s3c_freq_dbg("%s: setting refresh 0x%08lx\n", __func__, refresh); + __raw_writel(refresh, S3C2412_REFRESH); +} + +/* set the default cpu frequency information, based on an 200MHz part + * as we have no other way of detecting the speed rating in software. + */ + +static struct s3c_cpufreq_info s3c2412_cpufreq_info = { + .max = { + .fclk = 200000000, + .hclk = 100000000, + .pclk = 50000000, + }, + + .latency = 5000000, /* 5ms */ + + .locktime_m = 150, + .locktime_u = 150, + .locktime_bits = 16, + + .name = "s3c2412", + .set_refresh = s3c2412_cpufreq_setrefresh, + .set_divs = s3c2412_cpufreq_setdivs, + .calc_divs = s3c2412_cpufreq_calcdivs, + + .calc_iotiming = s3c2412_iotiming_calc, + .set_iotiming = s3c2412_iotiming_set, + .get_iotiming = s3c2412_iotiming_get, + + .resume_clocks = s3c2412_setup_clocks, + + .debug_io_show = s3c_cpufreq_debugfs_call(s3c2412_iotiming_debugfs), +}; + +static int s3c2412_cpufreq_add(struct sys_device *sysdev) +{ + unsigned long fclk_rate; + + hclk = clk_get(NULL, "hclk"); + if (IS_ERR(hclk)) { + printk(KERN_ERR "%s: cannot find hclk clock\n", __func__); + return -ENOENT; + } + + fclk = clk_get(NULL, "fclk"); + if (IS_ERR(fclk)) { + printk(KERN_ERR "%s: cannot find fclk clock\n", __func__); + goto err_fclk; + } + + fclk_rate = clk_get_rate(fclk); + if (fclk_rate > 200000000) { + printk(KERN_INFO + "%s: fclk %ld MHz, assuming 266MHz capable part\n", + __func__, fclk_rate / 1000000); + s3c2412_cpufreq_info.max.fclk = 266000000; + s3c2412_cpufreq_info.max.hclk = 133000000; + s3c2412_cpufreq_info.max.pclk = 66000000; + } + + armclk = clk_get(NULL, "armclk"); + if (IS_ERR(armclk)) { + printk(KERN_ERR "%s: cannot find arm clock\n", __func__); + goto err_armclk; + } + + xtal = clk_get(NULL, "xtal"); + if (IS_ERR(xtal)) { + printk(KERN_ERR "%s: cannot find xtal clock\n", __func__); + goto err_xtal; + } + + return s3c_cpufreq_register(&s3c2412_cpufreq_info); + +err_xtal: + clk_put(armclk); +err_armclk: + clk_put(fclk); +err_fclk: + clk_put(hclk); + + return -ENOENT; +} + +static struct sysdev_driver s3c2412_cpufreq_driver = { + .add = s3c2412_cpufreq_add, +}; + +static int s3c2412_cpufreq_init(void) +{ + return sysdev_driver_register(&s3c2412_sysclass, + &s3c2412_cpufreq_driver); +} + +arch_initcall(s3c2412_cpufreq_init); diff --git a/arch/arm/mach-s3c2412/s3c2412.c b/arch/arm/mach-s3c2412/s3c2412.c index 5b5aba69ec3..bef39f77729 100644 --- a/arch/arm/mach-s3c2412/s3c2412.c +++ b/arch/arm/mach-s3c2412/s3c2412.c @@ -69,6 +69,18 @@ static struct map_desc s3c2412_iodesc[] __initdata = { IODESC_ENT(CLKPWR), IODESC_ENT(TIMER), IODESC_ENT(WATCHDOG), + { + .virtual = (unsigned long)S3C2412_VA_SSMC, + .pfn = __phys_to_pfn(S3C2412_PA_SSMC), + .length = SZ_1M, + .type = MT_DEVICE, + }, + { + .virtual = (unsigned long)S3C2412_VA_EBI, + .pfn = __phys_to_pfn(S3C2412_PA_EBI), + .length = SZ_1M, + .type = MT_DEVICE, + }, }; /* uart registration process */ diff --git a/arch/arm/mach-s3c2440/Kconfig b/arch/arm/mach-s3c2440/Kconfig index 8cfeaec3730..8ae1b288f7f 100644 --- a/arch/arm/mach-s3c2440/Kconfig +++ b/arch/arm/mach-s3c2440/Kconfig @@ -33,6 +33,7 @@ config MACH_ANUBIS select PM_SIMTEC if PM select HAVE_PATA_PLATFORM select S3C24XX_GPIO_EXTRA64 + select S3C2440_XTAL_12000000 select S3C_DEV_USB_HOST help Say Y here if you are using the Simtec Electronics ANUBIS @@ -44,6 +45,8 @@ config MACH_OSIRIS select S3C24XX_DCLK select PM_SIMTEC if PM select S3C24XX_GPIO_EXTRA128 + select S3C2440_XTAL_12000000 + select S3C2410_IOTIMING if S3C2440_CPUFREQ select S3C_DEV_USB_HOST help Say Y here if you are using the Simtec IM2440D20 module, also @@ -52,6 +55,7 @@ config MACH_OSIRIS config MACH_RX3715 bool "HP iPAQ rx3715" select CPU_S3C2440 + select S3C2440_XTAL_16934400 select PM_H1940 if PM help Say Y here if you are using the HP iPAQ rx3715. @@ -59,6 +63,7 @@ config MACH_RX3715 config ARCH_S3C2440 bool "SMDK2440" select CPU_S3C2440 + select S3C2440_XTAL_16934400 select MACH_SMDK select S3C_DEV_USB_HOST help @@ -67,6 +72,7 @@ config ARCH_S3C2440 config MACH_NEXCODER_2440 bool "NexVision NEXCODER 2440 Light Board" select CPU_S3C2440 + select S3C2440_XTAL_12000000 select S3C_DEV_USB_HOST help Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board @@ -75,6 +81,7 @@ config SMDK2440_CPU2440 bool "SMDK2440 with S3C2440 CPU module" depends on ARCH_S3C2440 default y if ARCH_S3C2440 + select S3C2440_XTAL_16934400 select CPU_S3C2440 config MACH_AT2440EVB diff --git a/arch/arm/mach-s3c2440/mach-osiris.c b/arch/arm/mach-s3c2440/mach-osiris.c index cba064b49a6..2105a41281a 100644 --- a/arch/arm/mach-s3c2440/mach-osiris.c +++ b/arch/arm/mach-s3c2440/mach-osiris.c @@ -34,6 +34,7 @@ #include <asm/irq.h> #include <asm/mach-types.h> +#include <plat/cpu-freq.h> #include <plat/regs-serial.h> #include <mach/regs-gpio.h> #include <mach/regs-mem.h> @@ -351,6 +352,12 @@ static struct clk *osiris_clocks[] __initdata = { &s3c24xx_uclk, }; +static struct s3c_cpufreq_board __initdata osiris_cpufreq = { + .refresh = 7800, /* refresh period is 7.8usec */ + .auto_io = 1, + .need_io = 1, +}; + static void __init osiris_map_io(void) { unsigned long flags; @@ -402,6 +409,8 @@ static void __init osiris_init(void) s3c_i2c0_set_platdata(NULL); + s3c_cpufreq_setboard(&osiris_cpufreq); + i2c_register_board_info(0, osiris_i2c_devs, ARRAY_SIZE(osiris_i2c_devs)); diff --git a/arch/arm/mach-s3c6400/include/mach/map.h b/arch/arm/mach-s3c6400/include/mach/map.h index 5057d9948d3..e02e6c38a39 100644 --- a/arch/arm/mach-s3c6400/include/mach/map.h +++ b/arch/arm/mach-s3c6400/include/mach/map.h @@ -49,7 +49,7 @@ #define S3C64XX_PA_IIC1 (0x7F00F000) #define S3C64XX_PA_GPIO (0x7F008000) -#define S3C64XX_VA_GPIO S3C_ADDR(0x00500000) +#define S3C64XX_VA_GPIO S3C_ADDR_CPU(0x00000000) #define S3C64XX_SZ_GPIO SZ_4K #define S3C64XX_PA_SDRAM (0x50000000) @@ -57,7 +57,7 @@ #define S3C64XX_PA_VIC1 (0x71300000) #define S3C64XX_PA_MODEM (0x74108000) -#define S3C64XX_VA_MODEM S3C_ADDR(0x00600000) +#define S3C64XX_VA_MODEM S3C_ADDR_CPU(0x00100000) #define S3C64XX_PA_USBHOST (0x74300000) diff --git a/arch/arm/plat-s3c/include/plat/cpu-freq.h b/arch/arm/plat-s3c/include/plat/cpu-freq.h index c86a13307e9..7b982b7f28c 100644 --- a/arch/arm/plat-s3c/include/plat/cpu-freq.h +++ b/arch/arm/plat-s3c/include/plat/cpu-freq.h @@ -17,6 +17,21 @@ struct s3c_cpufreq_info; struct s3c_cpufreq_board; struct s3c_iotimings; +/** + * struct s3c_freq - frequency information (mainly for core drivers) + * @fclk: The FCLK frequency in Hz. + * @armclk: The ARMCLK frequency in Hz. + * @hclk_tns: HCLK cycle time in 10ths of nano-seconds. + * @hclk: The HCLK frequency in Hz. + * @pclk: The PCLK frequency in Hz. + * + * This contains the frequency information about the current configuration + * mainly for the core drivers to ensure we do not end up passing about + * a large number of parameters. + * + * The @hclk_tns field is a useful cache for the parts of the drivers that + * need to calculate IO timings and suchlike. + */ struct s3c_freq { unsigned long fclk; unsigned long armclk; @@ -25,48 +40,84 @@ struct s3c_freq { unsigned long pclk; }; -/* wrapper 'struct cpufreq_freqs' so that any drivers receiving the +/** + * struct s3c_cpufreq_freqs - s3c cpufreq notification information. + * @freqs: The cpufreq setting information. + * @old: The old clock settings. + * @new: The new clock settings. + * @pll_changing: Set if the PLL is changing. + * + * Wrapper 'struct cpufreq_freqs' so that any drivers receiving the * notification can use this information that is not provided by just * having the core frequency alone. + * + * The pll_changing flag is used to indicate if the PLL itself is + * being set during this change. This is important as the clocks + * will temporarily be set to the XTAL clock during this time, so + * drivers may want to close down their output during this time. + * + * Note, this is not being used by any current drivers and therefore + * may be removed in the future. */ - struct s3c_cpufreq_freqs { struct cpufreq_freqs freqs; struct s3c_freq old; struct s3c_freq new; + + unsigned int pll_changing:1; }; #define to_s3c_cpufreq(_cf) container_of(_cf, struct s3c_cpufreq_freqs, freqs) +/** + * struct s3c_clkdivs - clock divisor information + * @p_divisor: Divisor from FCLK to PCLK. + * @h_divisor: Divisor from FCLK to HCLK. + * @arm_divisor: Divisor from FCLK to ARMCLK (not all CPUs). + * @dvs: Non-zero if using DVS mode for ARMCLK. + * + * Divisor settings for the core clocks. + */ struct s3c_clkdivs { - int p_divisor; /* fclk / pclk */ - int h_divisor; /* fclk / hclk */ - int arm_divisor; /* not all cpus have this. */ - unsigned char dvs; /* using dvs mode to arm. */ + int p_divisor; + int h_divisor; + int arm_divisor; + unsigned char dvs; }; #define PLLVAL(_m, _p, _s) (((_m) << 12) | ((_p) << 4) | (_s)) +/** + * struct s3c_pllval - PLL value entry. + * @freq: The frequency for this entry in Hz. + * @pll_reg: The PLL register setting for this PLL value. + */ struct s3c_pllval { unsigned long freq; unsigned long pll_reg; }; -struct s3c_cpufreq_config { - struct s3c_freq freq; - struct s3c_pllval pll; - struct s3c_clkdivs divs; - struct s3c_cpufreq_info *info; /* for core, not drivers */ - struct s3c_cpufreq_board *board; -}; - -/* s3c_cpufreq_board +/** + * struct s3c_cpufreq_board - per-board cpu frequency informatin + * @refresh: The SDRAM refresh period in nanoseconds. + * @auto_io: Set if the IO timing settings should be generated from the + * initialisation time hardware registers. + * @need_io: Set if the board has external IO on any of the chipselect + * lines that will require the hardware timing registers to be + * updated on a clock change. + * @max: The maxium frequency limits for the system. Any field that + * is left at zero will use the CPU's settings. + * + * This contains the board specific settings that affect how the CPU + * drivers chose settings. These include the memory refresh and IO + * timing information. * - * per-board configuraton information, such as memory refresh and - * how to initialise IO timings. + * Registration depends on the driver being used, the ARMCLK only + * implementation does not currently need this but the older style + * driver requires this to be available. */ struct s3c_cpufreq_board { - unsigned int refresh; /* refresh period in ns */ + unsigned int refresh; unsigned int auto_io:1; /* automatically init io timings. */ unsigned int need_io:1; /* set if needs io timing support. */ diff --git a/arch/arm/plat-s3c/include/plat/cpu.h b/arch/arm/plat-s3c/include/plat/cpu.h index be541cbba07..fbc3d498e02 100644 --- a/arch/arm/plat-s3c/include/plat/cpu.h +++ b/arch/arm/plat-s3c/include/plat/cpu.h @@ -65,6 +65,7 @@ extern struct sys_timer s3c24xx_timer; /* system device classes */ extern struct sysdev_class s3c2410_sysclass; +extern struct sysdev_class s3c2410a_sysclass; extern struct sysdev_class s3c2412_sysclass; extern struct sysdev_class s3c2440_sysclass; extern struct sysdev_class s3c2442_sysclass; diff --git a/arch/arm/plat-s3c/include/plat/map-base.h b/arch/arm/plat-s3c/include/plat/map-base.h index b84289d32a5..250be311c85 100644 --- a/arch/arm/plat-s3c/include/plat/map-base.h +++ b/arch/arm/plat-s3c/include/plat/map-base.h @@ -32,9 +32,15 @@ #define S3C_VA_IRQ S3C_ADDR(0x00000000) /* irq controller(s) */ #define S3C_VA_SYS S3C_ADDR(0x00100000) /* system control */ -#define S3C_VA_MEM S3C_ADDR(0x00200000) /* system control */ +#define S3C_VA_MEM S3C_ADDR(0x00200000) /* memory control */ #define S3C_VA_TIMER S3C_ADDR(0x00300000) /* timer block */ #define S3C_VA_WATCHDOG S3C_ADDR(0x00400000) /* watchdog */ #define S3C_VA_UART S3C_ADDR(0x01000000) /* UART */ +/* This is used for the CPU specific mappings that may be needed, so that + * they do not need to directly used S3C_ADDR() and thus make it easier to + * modify the space for mapping. + */ +#define S3C_ADDR_CPU(x) S3C_ADDR(0x00500000 + (x)) + #endif /* __ASM_PLAT_MAP_H */ diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig index aaae456018b..2f914568359 100644 --- a/arch/arm/plat-s3c24xx/Kconfig +++ b/arch/arm/plat-s3c24xx/Kconfig @@ -34,6 +34,40 @@ config CPU_S3C244X help Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems. +config S3C2440_CPUFREQ + bool "S3C2440/S3C2442 CPU Frequency scaling support" + depends on CPU_FREQ_S3C24XX && (CPU_S3C2440 || CPU_S3C2442) + select S3C2410_CPUFREQ_UTILS + default y + help + CPU Frequency scaling support for S3C2440 and S3C2442 SoC CPUs. + +config S3C2440_XTAL_12000000 + bool + help + Indicate that the build needs to support 12MHz system + crystal. + +config S3C2440_XTAL_16934400 + bool + help + Indicate that the build needs to support 16.9344MHz system + crystal. + +config S3C2440_PLL_12000000 + bool + depends on S3C2440_CPUFREQ && S3C2440_XTAL_12000000 + default y if CPU_FREQ_S3C24XX_PLL + help + PLL tables for S3C2440 or S3C2442 CPUs with 12MHz crystals. + +config S3C2440_PLL_16934400 + bool + depends on S3C2440_CPUFREQ && S3C2440_XTAL_16934400 + default y if CPU_FREQ_S3C24XX_PLL + help + PLL tables for S3C2440 or S3C2442 CPUs with 16.934MHz crystals. + config S3C24XX_PWM bool "PWM device support" select HAVE_PWM @@ -113,6 +147,31 @@ config S3C24XX_SPI_BUS1_GPD8_GPD9_GPD10 # common code for s3c24xx based machines, such as the SMDKs. +# cpu frequency items common between s3c2410 and s3c2440/s3c2442 + +config S3C2410_IOTIMING + bool + depends on CPU_FREQ_S3C24XX + help + Internal node to select io timing code that is common to the s3c2410 + and s3c2440/s3c2442 cpu frequency support. + +config S3C2410_CPUFREQ_UTILS + bool + depends on CPU_FREQ_S3C24XX + help + Internal node to select timing code that is common to the s3c2410 + and s3c2440/s3c244 cpu frequency support. + +# cpu frequency support common to s3c2412, s3c2413 and s3c2442 + +config S3C2412_IOTIMING + bool + depends on CPU_FREQ_S3C24XX && (CPU_S3C2412 || CPU_S3C2443) + help + Intel node to select io timing code that is common to the s3c2412 + and the s3c2443. + config MACH_SMDK bool help diff --git a/arch/arm/plat-s3c24xx/Makefile b/arch/arm/plat-s3c24xx/Makefile index 59416796fb1..651315c95ec 100644 --- a/arch/arm/plat-s3c24xx/Makefile +++ b/arch/arm/plat-s3c24xx/Makefile @@ -20,11 +20,18 @@ obj-y += gpiolib.o obj-y += clock.o obj-$(CONFIG_S3C24XX_DCLK) += clock-dclk.o +obj-$(CONFIG_CPU_FREQ_S3C24XX) += cpu-freq.o +obj-$(CONFIG_CPU_FREQ_S3C24XX_DEBUGFS) += cpu-freq-debugfs.o + # Architecture dependant builds obj-$(CONFIG_CPU_S3C244X) += s3c244x.o obj-$(CONFIG_CPU_S3C244X) += s3c244x-irq.o obj-$(CONFIG_CPU_S3C244X) += s3c244x-clock.o +obj-$(CONFIG_S3C2440_CPUFREQ) += s3c2440-cpufreq.o +obj-$(CONFIG_S3C2440_PLL_12000000) += s3c2440-pll-12000000.o +obj-$(CONFIG_S3C2440_PLL_16934400) += s3c2440-pll-16934400.o + obj-$(CONFIG_PM_SIMTEC) += pm-simtec.o obj-$(CONFIG_PM) += pm.o obj-$(CONFIG_PM) += irq-pm.o @@ -33,6 +40,9 @@ obj-$(CONFIG_S3C24XX_PWM) += pwm.o obj-$(CONFIG_S3C2410_CLOCK) += s3c2410-clock.o obj-$(CONFIG_S3C2410_DMA) += dma.o obj-$(CONFIG_S3C24XX_ADC) += adc.o +obj-$(CONFIG_S3C2410_IOTIMING) += s3c2410-iotiming.o +obj-$(CONFIG_S3C2412_IOTIMING) += s3c2412-iotiming.o +obj-$(CONFIG_S3C2410_CPUFREQ_UTILS) += s3c2410-cpufreq-utils.o # device specific setup and/or initialisation obj-$(CONFIG_ARCH_S3C2410) += setup-i2c.o diff --git a/arch/arm/plat-s3c24xx/cpu-freq-debugfs.c b/arch/arm/plat-s3c24xx/cpu-freq-debugfs.c new file mode 100644 index 00000000000..a9276667c2f --- /dev/null +++ b/arch/arm/plat-s3c24xx/cpu-freq-debugfs.c @@ -0,0 +1,199 @@ +/* linux/arch/arm/plat-s3c24xx/cpu-freq-debugfs.c + * + * Copyright (c) 2009 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C24XX CPU Frequency scaling - debugfs status support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/cpufreq.h> +#include <linux/debugfs.h> +#include <linux/seq_file.h> +#include <linux/err.h> + +#include <plat/cpu-freq-core.h> + +static struct dentry *dbgfs_root; +static struct dentry *dbgfs_file_io; +static struct dentry *dbgfs_file_info; +static struct dentry *dbgfs_file_board; + +#define print_ns(x) ((x) / 10), ((x) % 10) + +static void show_max(struct seq_file *seq, struct s3c_freq *f) +{ + seq_printf(seq, "MAX: F=%lu, H=%lu, P=%lu, A=%lu\n", + f->fclk, f->hclk, f->pclk, f->armclk); +} + +static int board_show(struct seq_file *seq, void *p) +{ + struct s3c_cpufreq_config *cfg; + struct s3c_cpufreq_board *brd; + + cfg = s3c_cpufreq_getconfig(); + if (!cfg) { + seq_printf(seq, "no configuration registered\n"); + return 0; + } + + brd = cfg->board; + if (!brd) { + seq_printf(seq, "no board definition set?\n"); + return 0; + } + + seq_printf(seq, "SDRAM refresh %u ns\n", brd->refresh); + seq_printf(seq, "auto_io=%u\n", brd->auto_io); + seq_printf(seq, "need_io=%u\n", brd->need_io); + + show_max(seq, &brd->max); + + + return 0; +} + +static int fops_board_open(struct inode *inode, struct file *file) +{ + return single_open(file, board_show, NULL); +} + +static const struct file_operations fops_board = { + .open = fops_board_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, + .owner = THIS_MODULE, +}; + +static int info_show(struct seq_file *seq, void *p) +{ + struct s3c_cpufreq_config *cfg; + + cfg = s3c_cpufreq_getconfig(); + if (!cfg) { + seq_printf(seq, "no configuration registered\n"); + return 0; + } + + seq_printf(seq, " FCLK %ld Hz\n", cfg->freq.fclk); + seq_printf(seq, " HCLK %ld Hz (%lu.%lu ns)\n", + cfg->freq.hclk, print_ns(cfg->freq.hclk_tns)); + seq_printf(seq, " PCLK %ld Hz\n", cfg->freq.hclk); + seq_printf(seq, "ARMCLK %ld Hz\n", cfg->freq.armclk); + seq_printf(seq, "\n"); + + show_max(seq, &cfg->max); + + seq_printf(seq, "Divisors: P=%d, H=%d, A=%d, dvs=%s\n", + cfg->divs.h_divisor, cfg->divs.p_divisor, + cfg->divs.arm_divisor, cfg->divs.dvs ? "on" : "off"); + seq_printf(seq, "\n"); + + seq_printf(seq, "lock_pll=%u\n", cfg->lock_pll); + + return 0; +} + +static int fops_info_open(struct inode *inode, struct file *file) +{ + return single_open(file, info_show, NULL); +} + +static const struct file_operations fops_info = { + .open = fops_info_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, + .owner = THIS_MODULE, +}; + +static int io_show(struct seq_file *seq, void *p) +{ + void (*show_bank)(struct seq_file *, struct s3c_cpufreq_config *, union s3c_iobank *); + struct s3c_cpufreq_config *cfg; + struct s3c_iotimings *iot; + union s3c_iobank *iob; + int bank; + + cfg = s3c_cpufreq_getconfig(); + if (!cfg) { + seq_printf(seq, "no configuration registered\n"); + return 0; + } + + show_bank = cfg->info->debug_io_show; + if (!show_bank) { + seq_printf(seq, "no code to show bank timing\n"); + return 0; + } + + iot = s3c_cpufreq_getiotimings(); + if (!iot) { + seq_printf(seq, "no io timings registered\n"); + return 0; + } + + seq_printf(seq, "hclk period is %lu.%lu ns\n", print_ns(cfg->freq.hclk_tns)); + + for (bank = 0; bank < MAX_BANKS; bank++) { + iob = &iot->bank[bank]; + + seq_printf(seq, "bank %d: ", bank); + + if (!iob->io_2410) { + seq_printf(seq, "nothing set\n"); + continue; + } + + show_bank(seq, cfg, iob); + } + + return 0; +} + +static int fops_io_open(struct inode *inode, struct file *file) +{ + return single_open(file, io_show, NULL); +} + +static const struct file_operations fops_io = { + .open = fops_io_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, + .owner = THIS_MODULE, +}; + + +static int __init s3c_freq_debugfs_init(void) +{ + dbgfs_root = debugfs_create_dir("s3c-cpufreq", NULL); + if (IS_ERR(dbgfs_root)) { + printk(KERN_ERR "%s: error creating debugfs root\n", __func__); + return PTR_ERR(dbgfs_root); + } + + dbgfs_file_io = debugfs_create_file("io-timing", S_IRUGO, dbgfs_root, + NULL, &fops_io); + + dbgfs_file_info = debugfs_create_file("info", S_IRUGO, dbgfs_root, + NULL, &fops_info); + + dbgfs_file_board = debugfs_create_file("board", S_IRUGO, dbgfs_root, + NULL, &fops_board); + + return 0; +} + +late_initcall(s3c_freq_debugfs_init); + diff --git a/arch/arm/plat-s3c24xx/cpu-freq.c b/arch/arm/plat-s3c24xx/cpu-freq.c new file mode 100644 index 00000000000..4f1b789a117 --- /dev/null +++ b/arch/arm/plat-s3c24xx/cpu-freq.c @@ -0,0 +1,716 @@ +/* linux/arch/arm/plat-s3c24xx/cpu-freq.c + * + * Copyright (c) 2006,2007,2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C24XX CPU Frequency scaling + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/cpufreq.h> +#include <linux/cpu.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/sysdev.h> +#include <linux/kobject.h> +#include <linux/sysfs.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <plat/cpu.h> +#include <plat/clock.h> +#include <plat/cpu-freq-core.h> + +#include <mach/regs-clock.h> + +/* note, cpufreq support deals in kHz, no Hz */ + +static struct cpufreq_driver s3c24xx_driver; +static struct s3c_cpufreq_config cpu_cur; +static struct s3c_iotimings s3c24xx_iotiming; +static struct cpufreq_frequency_table *pll_reg; +static unsigned int last_target = ~0; +static unsigned int ftab_size; +static struct cpufreq_frequency_table *ftab; + +static struct clk *_clk_mpll; +static struct clk *_clk_xtal; +static struct clk *clk_fclk; +static struct clk *clk_hclk; +static struct clk *clk_pclk; +static struct clk *clk_arm; + +#ifdef CONFIG_CPU_FREQ_S3C24XX_DEBUGFS +struct s3c_cpufreq_config *s3c_cpufreq_getconfig(void) +{ + return &cpu_cur; +} + +struct s3c_iotimings *s3c_cpufreq_getiotimings(void) +{ + return &s3c24xx_iotiming; +} +#endif /* CONFIG_CPU_FREQ_S3C24XX_DEBUGFS */ + +static void s3c_cpufreq_getcur(struct s3c_cpufreq_config *cfg) +{ + unsigned long fclk, pclk, hclk, armclk; + + cfg->freq.fclk = fclk = clk_get_rate(clk_fclk); + cfg->freq.hclk = hclk = clk_get_rate(clk_hclk); + cfg->freq.pclk = pclk = clk_get_rate(clk_pclk); + cfg->freq.armclk = armclk = clk_get_rate(clk_arm); + + cfg->pll.index = __raw_readl(S3C2410_MPLLCON); + cfg->pll.frequency = fclk; + + cfg->freq.hclk_tns = 1000000000 / (cfg->freq.hclk / 10); + + cfg->divs.h_divisor = fclk / hclk; + cfg->divs.p_divisor = fclk / pclk; +} + +static inline void s3c_cpufreq_calc(struct s3c_cpufreq_config *cfg) +{ + unsigned long pll = cfg->pll.frequency; + + cfg->freq.fclk = pll; + cfg->freq.hclk = pll / cfg->divs.h_divisor; + cfg->freq.pclk = pll / cfg->divs.p_divisor; + + /* convert hclk into 10ths of nanoseconds for io calcs */ + cfg->freq.hclk_tns = 1000000000 / (cfg->freq.hclk / 10); +} + +static inline int closer(unsigned int target, unsigned int n, unsigned int c) +{ + int diff_cur = abs(target - c); + int diff_new = abs(target - n); + + return (diff_new < diff_cur); +} + +static void s3c_cpufreq_show(const char *pfx, + struct s3c_cpufreq_config *cfg) +{ + s3c_freq_dbg("%s: Fvco=%u, F=%lu, A=%lu, H=%lu (%u), P=%lu (%u)\n", + pfx, cfg->pll.frequency, cfg->freq.fclk, cfg->freq.armclk, + cfg->freq.hclk, cfg->divs.h_divisor, + cfg->freq.pclk, cfg->divs.p_divisor); +} + +/* functions to wrapper the driver info calls to do the cpu specific work */ + +static void s3c_cpufreq_setio(struct s3c_cpufreq_config *cfg) +{ + if (cfg->info->set_iotiming) + (cfg->info->set_iotiming)(cfg, &s3c24xx_iotiming); +} + +static int s3c_cpufreq_calcio(struct s3c_cpufreq_config *cfg) +{ + if (cfg->info->calc_iotiming) + return (cfg->info->calc_iotiming)(cfg, &s3c24xx_iotiming); + + return 0; +} + +static void s3c_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg) +{ + (cfg->info->set_refresh)(cfg); +} + +static void s3c_cpufreq_setdivs(struct s3c_cpufreq_config *cfg) +{ + (cfg->info->set_divs)(cfg); +} + +static int s3c_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg) +{ + return (cfg->info->calc_divs)(cfg); +} + +static void s3c_cpufreq_setfvco(struct s3c_cpufreq_config *cfg) +{ + (cfg->info->set_fvco)(cfg); +} + +static inline void s3c_cpufreq_resume_clocks(void) +{ + cpu_cur.info->resume_clocks(); +} + +static inline void s3c_cpufreq_updateclk(struct clk *clk, + unsigned int freq) +{ + clk_set_rate(clk, freq); +} + +static int s3c_cpufreq_settarget(struct cpufreq_policy *policy, + unsigned int target_freq, + struct cpufreq_frequency_table *pll) +{ + struct s3c_cpufreq_freqs freqs; + struct s3c_cpufreq_config cpu_new; + unsigned long flags; + + cpu_new = cpu_cur; /* copy new from current */ + + s3c_cpufreq_show("cur", &cpu_cur); + + /* TODO - check for DMA currently outstanding */ + + cpu_new.pll = pll ? *pll : cpu_cur.pll; + + if (pll) + freqs.pll_changing = 1; + + /* update our frequencies */ + + cpu_new.freq.armclk = target_freq; + cpu_new.freq.fclk = cpu_new.pll.frequency; + + if (s3c_cpufreq_calcdivs(&cpu_new) < 0) { + printk(KERN_ERR "no divisors for %d\n", target_freq); + goto err_notpossible; + } + + s3c_freq_dbg("%s: got divs\n", __func__); + + s3c_cpufreq_calc(&cpu_new); + + s3c_freq_dbg("%s: calculated frequencies for new\n", __func__); + + if (cpu_new.freq.hclk != cpu_cur.freq.hclk) { + if (s3c_cpufreq_calcio(&cpu_new) < 0) { + printk(KERN_ERR "%s: no IO timings\n", __func__); + goto err_notpossible; + } + } + + s3c_cpufreq_show("new", &cpu_new); + + /* setup our cpufreq parameters */ + + freqs.old = cpu_cur.freq; + freqs.new = cpu_new.freq; + + freqs.freqs.cpu = 0; + freqs.freqs.old = cpu_cur.freq.armclk / 1000; + freqs.freqs.new = cpu_new.freq.armclk / 1000; + + /* update f/h/p clock settings before we issue the change + * notification, so that drivers do not need to do anything + * special if they want to recalculate on CPUFREQ_PRECHANGE. */ + + s3c_cpufreq_updateclk(_clk_mpll, cpu_new.pll.frequency); + s3c_cpufreq_updateclk(clk_fclk, cpu_new.freq.fclk); + s3c_cpufreq_updateclk(clk_hclk, cpu_new.freq.hclk); + s3c_cpufreq_updateclk(clk_pclk, cpu_new.freq.pclk); + + /* start the frequency change */ + + if (policy) + cpufreq_notify_transition(&freqs.freqs, CPUFREQ_PRECHANGE); + + /* If hclk is staying the same, then we do not need to + * re-write the IO or the refresh timings whilst we are changing + * speed. */ + + local_irq_save(flags); + + /* is our memory clock slowing down? */ + if (cpu_new.freq.hclk < cpu_cur.freq.hclk) { + s3c_cpufreq_setrefresh(&cpu_new); + s3c_cpufreq_setio(&cpu_new); + } + + if (cpu_new.freq.fclk == cpu_cur.freq.fclk) { + /* not changing PLL, just set the divisors */ + + s3c_cpufreq_setdivs(&cpu_new); + } else { + if (cpu_new.freq.fclk < cpu_cur.freq.fclk) { + /* slow the cpu down, then set divisors */ + + s3c_cpufreq_setfvco(&cpu_new); + s3c_cpufreq_setdivs(&cpu_new); + } else { + /* set the divisors, then speed up */ + + s3c_cpufreq_setdivs(&cpu_new); + s3c_cpufreq_setfvco(&cpu_new); + } + } + + /* did our memory clock speed up */ + if (cpu_new.freq.hclk > cpu_cur.freq.hclk) { + s3c_cpufreq_setrefresh(&cpu_new); + s3c_cpufreq_setio(&cpu_new); + } + + /* update our current settings */ + cpu_cur = cpu_new; + + local_irq_restore(flags); + + /* notify everyone we've done this */ + if (policy) + cpufreq_notify_transition(&freqs.freqs, CPUFREQ_POSTCHANGE); + + s3c_freq_dbg("%s: finished\n", __func__); + return 0; + + err_notpossible: + printk(KERN_ERR "no compatible settings for %d\n", target_freq); + return -EINVAL; +} + +/* s3c_cpufreq_target + * + * called by the cpufreq core to adjust the frequency that the CPU + * is currently running at. + */ + +static int s3c_cpufreq_target(struct cpufreq_policy *policy, + unsigned int target_freq, + unsigned int relation) +{ + struct cpufreq_frequency_table *pll; + unsigned int index; + + /* avoid repeated calls which cause a needless amout of duplicated + * logging output (and CPU time as the calculation process is + * done) */ + if (target_freq == last_target) + return 0; + + last_target = target_freq; + + s3c_freq_dbg("%s: policy %p, target %u, relation %u\n", + __func__, policy, target_freq, relation); + + if (ftab) { + if (cpufreq_frequency_table_target(policy, ftab, + target_freq, relation, + &index)) { + s3c_freq_dbg("%s: table failed\n", __func__); + return -EINVAL; + } + + s3c_freq_dbg("%s: adjust %d to entry %d (%u)\n", __func__, + target_freq, index, ftab[index].frequency); + target_freq = ftab[index].frequency; + } + + target_freq *= 1000; /* convert target to Hz */ + + /* find the settings for our new frequency */ + + if (!pll_reg || cpu_cur.lock_pll) { + /* either we've not got any PLL values, or we've locked + * to the current one. */ + pll = NULL; + } else { + struct cpufreq_policy tmp_policy; + int ret; + + /* we keep the cpu pll table in Hz, to ensure we get an + * accurate value for the PLL output. */ + + tmp_policy.min = policy->min * 1000; + tmp_policy.max = policy->max * 1000; + tmp_policy.cpu = policy->cpu; + + /* cpufreq_frequency_table_target uses a pointer to 'index' + * which is the number of the table entry, not the value of + * the table entry's index field. */ + + ret = cpufreq_frequency_table_target(&tmp_policy, pll_reg, + target_freq, relation, + &index); + + if (ret < 0) { + printk(KERN_ERR "%s: no PLL available\n", __func__); + goto err_notpossible; + } + + pll = pll_reg + index; + + s3c_freq_dbg("%s: target %u => %u\n", + __func__, target_freq, pll->frequency); + + target_freq = pll->frequency; + } + + return s3c_cpufreq_settarget(policy, target_freq, pll); + + err_notpossible: + printk(KERN_ERR "no compatible settings for %d\n", target_freq); + return -EINVAL; +} + +static unsigned int s3c_cpufreq_get(unsigned int cpu) +{ + return clk_get_rate(clk_arm) / 1000; +} + +struct clk *s3c_cpufreq_clk_get(struct device *dev, const char *name) +{ + struct clk *clk; + + clk = clk_get(dev, name); + if (IS_ERR(clk)) + printk(KERN_ERR "cpufreq: failed to get clock '%s'\n", name); + + return clk; +} + +static int s3c_cpufreq_init(struct cpufreq_policy *policy) +{ + printk(KERN_INFO "%s: initialising policy %p\n", __func__, policy); + + if (policy->cpu != 0) + return -EINVAL; + + policy->cur = s3c_cpufreq_get(0); + policy->min = policy->cpuinfo.min_freq = 0; + policy->max = policy->cpuinfo.max_freq = cpu_cur.info->max.fclk / 1000; + policy->governor = CPUFREQ_DEFAULT_GOVERNOR; + + /* feed the latency information from the cpu driver */ + policy->cpuinfo.transition_latency = cpu_cur.info->latency; + + if (ftab) + cpufreq_frequency_table_cpuinfo(policy, ftab); + + return 0; +} + +static __init int s3c_cpufreq_initclks(void) +{ + _clk_mpll = s3c_cpufreq_clk_get(NULL, "mpll"); + _clk_xtal = s3c_cpufreq_clk_get(NULL, "xtal"); + clk_fclk = s3c_cpufreq_clk_get(NULL, "fclk"); + clk_hclk = s3c_cpufreq_clk_get(NULL, "hclk"); + clk_pclk = s3c_cpufreq_clk_get(NULL, "pclk"); + clk_arm = s3c_cpufreq_clk_get(NULL, "armclk"); + + if (IS_ERR(clk_fclk) || IS_ERR(clk_hclk) || IS_ERR(clk_pclk) || + IS_ERR(_clk_mpll) || IS_ERR(clk_arm) || IS_ERR(_clk_xtal)) { + printk(KERN_ERR "%s: could not get clock(s)\n", __func__); + return -ENOENT; + } + + printk(KERN_INFO "%s: clocks f=%lu,h=%lu,p=%lu,a=%lu\n", __func__, + clk_get_rate(clk_fclk) / 1000, + clk_get_rate(clk_hclk) / 1000, + clk_get_rate(clk_pclk) / 1000, + clk_get_rate(clk_arm) / 1000); + + return 0; +} + +static int s3c_cpufreq_verify(struct cpufreq_policy *policy) +{ + if (policy->cpu != 0) + return -EINVAL; + + return 0; +} + +#ifdef CONFIG_PM +static struct cpufreq_frequency_table suspend_pll; +static unsigned int suspend_freq; + +static int s3c_cpufreq_suspend(struct cpufreq_policy *policy, pm_message_t pmsg) +{ + suspend_pll.frequency = clk_get_rate(_clk_mpll); + suspend_pll.index = __raw_readl(S3C2410_MPLLCON); + suspend_freq = s3c_cpufreq_get(0) * 1000; + + return 0; +} + +static int s3c_cpufreq_resume(struct cpufreq_policy *policy) +{ + int ret; + + s3c_freq_dbg("%s: resuming with policy %p\n", __func__, policy); + + last_target = ~0; /* invalidate last_target setting */ + + /* first, find out what speed we resumed at. */ + s3c_cpufreq_resume_clocks(); + + /* whilst we will be called later on, we try and re-set the + * cpu frequencies as soon as possible so that we do not end + * up resuming devices and then immediatley having to re-set + * a number of settings once these devices have restarted. + * + * as a note, it is expected devices are not used until they + * have been un-suspended and at that time they should have + * used the updated clock settings. + */ + + ret = s3c_cpufreq_settarget(NULL, suspend_freq, &suspend_pll); + if (ret) { + printk(KERN_ERR "%s: failed to reset pll/freq\n", __func__); + return ret; + } + + return 0; +} +#else +#define s3c_cpufreq_resume NULL +#define s3c_cpufreq_suspend NULL +#endif + +static struct cpufreq_driver s3c24xx_driver = { + .flags = CPUFREQ_STICKY, + .verify = s3c_cpufreq_verify, + .target = s3c_cpufreq_target, + .get = s3c_cpufreq_get, + .init = s3c_cpufreq_init, + .suspend = s3c_cpufreq_suspend, + .resume = s3c_cpufreq_resume, + .name = "s3c24xx", +}; + + +int __init s3c_cpufreq_register(struct s3c_cpufreq_info *info) +{ + if (!info || !info->name) { + printk(KERN_ERR "%s: failed to pass valid information\n", + __func__); + return -EINVAL; + } + + printk(KERN_INFO "S3C24XX CPU Frequency driver, %s cpu support\n", + info->name); + + /* check our driver info has valid data */ + + BUG_ON(info->set_refresh == NULL); + BUG_ON(info->set_divs == NULL); + BUG_ON(info->calc_divs == NULL); + + /* info->set_fvco is optional, depending on whether there + * is a need to set the clock code. */ + + cpu_cur.info = info; + + /* Note, driver registering should probably update locktime */ + + return 0; +} + +int __init s3c_cpufreq_setboard(struct s3c_cpufreq_board *board) +{ + struct s3c_cpufreq_board *ours; + + if (!board) { + printk(KERN_INFO "%s: no board data\n", __func__); + return -EINVAL; + } + + /* Copy the board information so that each board can make this + * initdata. */ + + ours = kzalloc(sizeof(struct s3c_cpufreq_board), GFP_KERNEL); + if (ours == NULL) { + printk(KERN_ERR "%s: no memory\n", __func__); + return -ENOMEM; + } + + *ours = *board; + cpu_cur.board = ours; + + return 0; +} + +int __init s3c_cpufreq_auto_io(void) +{ + int ret; + + if (!cpu_cur.info->get_iotiming) { + printk(KERN_ERR "%s: get_iotiming undefined\n", __func__); + return -ENOENT; + } + + printk(KERN_INFO "%s: working out IO settings\n", __func__); + + ret = (cpu_cur.info->get_iotiming)(&cpu_cur, &s3c24xx_iotiming); + if (ret) + printk(KERN_ERR "%s: failed to get timings\n", __func__); + + return ret; +} + +/* if one or is zero, then return the other, otherwise return the min */ +#define do_min(_a, _b) ((_a) == 0 ? (_b) : (_b) == 0 ? (_a) : min(_a, _b)) + +/** + * s3c_cpufreq_freq_min - find the minimum settings for the given freq. + * @dst: The destination structure + * @a: One argument. + * @b: The other argument. + * + * Create a minimum of each frequency entry in the 'struct s3c_freq', + * unless the entry is zero when it is ignored and the non-zero argument + * used. + */ +static void s3c_cpufreq_freq_min(struct s3c_freq *dst, + struct s3c_freq *a, struct s3c_freq *b) +{ + dst->fclk = do_min(a->fclk, b->fclk); + dst->hclk = do_min(a->hclk, b->hclk); + dst->pclk = do_min(a->pclk, b->pclk); + dst->armclk = do_min(a->armclk, b->armclk); +} + +static inline u32 calc_locktime(u32 freq, u32 time_us) +{ + u32 result; + + result = freq * time_us; + result = DIV_ROUND_UP(result, 1000 * 1000); + + return result; +} + +static void s3c_cpufreq_update_loctkime(void) +{ + unsigned int bits = cpu_cur.info->locktime_bits; + u32 rate = (u32)clk_get_rate(_clk_xtal); + u32 val; + + if (bits == 0) { + WARN_ON(1); + return; + } + + val = calc_locktime(rate, cpu_cur.info->locktime_u) << bits; + val |= calc_locktime(rate, cpu_cur.info->locktime_m); + + printk(KERN_INFO "%s: new locktime is 0x%08x\n", __func__, val); + __raw_writel(val, S3C2410_LOCKTIME); +} + +static int s3c_cpufreq_build_freq(void) +{ + int size, ret; + + if (!cpu_cur.info->calc_freqtable) + return -EINVAL; + + kfree(ftab); + ftab = NULL; + + size = cpu_cur.info->calc_freqtable(&cpu_cur, NULL, 0); + size++; + + ftab = kmalloc(sizeof(struct cpufreq_frequency_table) * size, GFP_KERNEL); + if (!ftab) { + printk(KERN_ERR "%s: no memory for tables\n", __func__); + return -ENOMEM; + } + + ftab_size = size; + + ret = cpu_cur.info->calc_freqtable(&cpu_cur, ftab, size); + s3c_cpufreq_addfreq(ftab, ret, size, CPUFREQ_TABLE_END); + + return 0; +} + +static int __init s3c_cpufreq_initcall(void) +{ + int ret = 0; + + if (cpu_cur.info && cpu_cur.board) { + ret = s3c_cpufreq_initclks(); + if (ret) + goto out; + + /* get current settings */ + s3c_cpufreq_getcur(&cpu_cur); + s3c_cpufreq_show("cur", &cpu_cur); + + if (cpu_cur.board->auto_io) { + ret = s3c_cpufreq_auto_io(); + if (ret) { + printk(KERN_ERR "%s: failed to get io timing\n", + __func__); + goto out; + } + } + + if (cpu_cur.board->need_io && !cpu_cur.info->set_iotiming) { + printk(KERN_ERR "%s: no IO support registered\n", + __func__); + ret = -EINVAL; + goto out; + } + + if (!cpu_cur.info->need_pll) + cpu_cur.lock_pll = 1; + + s3c_cpufreq_update_loctkime(); + + s3c_cpufreq_freq_min(&cpu_cur.max, &cpu_cur.board->max, + &cpu_cur.info->max); + + if (cpu_cur.info->calc_freqtable) + s3c_cpufreq_build_freq(); + + ret = cpufreq_register_driver(&s3c24xx_driver); + } + + out: + return ret; +} + +late_initcall(s3c_cpufreq_initcall); + +/** + * s3c_plltab_register - register CPU PLL table. + * @plls: The list of PLL entries. + * @plls_no: The size of the PLL entries @plls. + * + * Register the given set of PLLs with the system. + */ +int __init s3c_plltab_register(struct cpufreq_frequency_table *plls, + unsigned int plls_no) +{ + struct cpufreq_frequency_table *vals; + unsigned int size; + + size = sizeof(struct cpufreq_frequency_table) * (plls_no + 1); + + vals = kmalloc(size, GFP_KERNEL); + if (vals) { + memcpy(vals, plls, size); + pll_reg = vals; + + /* write a terminating entry, we don't store it in the + * table that is stored in the kernel */ + vals += plls_no; + vals->frequency = CPUFREQ_TABLE_END; + + printk(KERN_INFO "cpufreq: %d PLL entries\n", plls_no); + } else + printk(KERN_ERR "cpufreq: no memory for PLL tables\n"); + + return vals ? 0 : -ENOMEM; +} diff --git a/arch/arm/plat-s3c24xx/cpu.c b/arch/arm/plat-s3c24xx/cpu.c index 1932b7e0da1..5447e60f393 100644 --- a/arch/arm/plat-s3c24xx/cpu.c +++ b/arch/arm/plat-s3c24xx/cpu.c @@ -81,7 +81,7 @@ static struct cpu_table cpu_ids[] __initdata = { .map_io = s3c2410_map_io, .init_clocks = s3c2410_init_clocks, .init_uarts = s3c2410_init_uarts, - .init = s3c2410_init, + .init = s3c2410a_init, .name = name_s3c2410a }, { diff --git a/arch/arm/plat-s3c24xx/include/plat/cpu-freq-core.h b/arch/arm/plat-s3c24xx/include/plat/cpu-freq-core.h new file mode 100644 index 00000000000..efeb025affc --- /dev/null +++ b/arch/arm/plat-s3c24xx/include/plat/cpu-freq-core.h @@ -0,0 +1,282 @@ +/* arch/arm/plat-s3c/include/plat/cpu-freq.h + * + * Copyright (c) 2006,2007,2009 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C CPU frequency scaling support - core support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <plat/cpu-freq.h> + +struct seq_file; + +#define MAX_BANKS (8) +#define S3C2412_MAX_IO (8) + +/** + * struct s3c2410_iobank_timing - IO bank timings for S3C2410 style timings + * @bankcon: The cached version of settings in this structure. + * @tacp: + * @tacs: Time from address valid to nCS asserted. + * @tcos: Time from nCS asserted to nOE or nWE asserted. + * @tacc: Time that nOE or nWE is asserted. + * @tcoh: Time nCS is held after nOE or nWE are released. + * @tcah: Time address is held for after + * @nwait_en: Whether nWAIT is enabled for this bank. + * + * This structure represents the IO timings for a S3C2410 style IO bank + * used by the CPU frequency support if it needs to change the settings + * of the IO. + */ +struct s3c2410_iobank_timing { + unsigned long bankcon; + unsigned int tacp; + unsigned int tacs; + unsigned int tcos; + unsigned int tacc; + unsigned int tcoh; /* nCS hold afrer nOE/nWE */ + unsigned int tcah; /* Address hold after nCS */ + unsigned char nwait_en; /* nWait enabled for bank. */ +}; + +/** + * struct s3c2412_iobank_timing - io timings for PL092 (S3C2412) style IO + * @idcy: The idle cycle time between transactions. + * @wstrd: nCS release to end of read cycle. + * @wstwr: nCS release to end of write cycle. + * @wstoen: nCS assertion to nOE assertion time. + * @wstwen: nCS assertion to nWE assertion time. + * @wstbrd: Burst ready delay. + * @smbidcyr: Register cache for smbidcyr value. + * @smbwstrd: Register cache for smbwstrd value. + * @smbwstwr: Register cache for smbwstwr value. + * @smbwstoen: Register cache for smbwstoen value. + * @smbwstwen: Register cache for smbwstwen value. + * @smbwstbrd: Register cache for smbwstbrd value. + * + * Timing information for a IO bank on an S3C2412 or similar system which + * uses a PL093 block. + */ +struct s3c2412_iobank_timing { + unsigned int idcy; + unsigned int wstrd; + unsigned int wstwr; + unsigned int wstoen; + unsigned int wstwen; + unsigned int wstbrd; + + /* register cache */ + unsigned char smbidcyr; + unsigned char smbwstrd; + unsigned char smbwstwr; + unsigned char smbwstoen; + unsigned char smbwstwen; + unsigned char smbwstbrd; +}; + +union s3c_iobank { + struct s3c2410_iobank_timing *io_2410; + struct s3c2412_iobank_timing *io_2412; +}; + +/** + * struct s3c_iotimings - Chip IO timings holder + * @bank: The timings for each IO bank. + */ +struct s3c_iotimings { + union s3c_iobank bank[MAX_BANKS]; +}; + +/** + * struct s3c_plltab - PLL table information. + * @vals: List of PLL values. + * @size: Size of the PLL table @vals. + */ +struct s3c_plltab { + struct s3c_pllval *vals; + int size; +}; + +/** + * struct s3c_cpufreq_config - current cpu frequency configuration + * @freq: The current settings for the core clocks. + * @max: Maxium settings, derived from core, board and user settings. + * @pll: The PLL table entry for the current PLL settings. + * @divs: The divisor settings for the core clocks. + * @info: The current core driver information. + * @board: The information for the board we are running on. + * @lock_pll: Set if the PLL settings cannot be changed. + * + * This is for the core drivers that need to know information about + * the current settings and values. It should not be needed by any + * device drivers. +*/ +struct s3c_cpufreq_config { + struct s3c_freq freq; + struct s3c_freq max; + struct cpufreq_frequency_table pll; + struct s3c_clkdivs divs; + struct s3c_cpufreq_info *info; /* for core, not drivers */ + struct s3c_cpufreq_board *board; + + unsigned int lock_pll:1; +}; + +/** + * struct s3c_cpufreq_info - Information for the CPU frequency driver. + * @name: The name of this implementation. + * @max: The maximum frequencies for the system. + * @latency: Transition latency to give to cpufreq. + * @locktime_m: The lock-time in uS for the MPLL. + * @locktime_u: The lock-time in uS for the UPLL. + * @locttime_bits: The number of bits each LOCKTIME field. + * @need_pll: Set if this driver needs to change the PLL values to acheive + * any frequency changes. This is really only need by devices like the + * S3C2410 where there is no or limited divider between the PLL and the + * ARMCLK. + * @resume_clocks: Update the clocks on resume. + * @get_iotiming: Get the current IO timing data, mainly for use at start. + * @set_iotiming: Update the IO timings from the cached copies calculated + * from the @calc_iotiming entry when changing the frequency. + * @calc_iotiming: Calculate and update the cached copies of the IO timings + * from the newly calculated frequencies. + * @calc_freqtable: Calculate (fill in) the given frequency table from the + * current frequency configuration. If the table passed in is NULL, + * then the return is the number of elements to be filled for allocation + * of the table. + * @set_refresh: Set the memory refresh configuration. + * @set_fvco: Set the PLL frequencies. + * @set_divs: Update the clock divisors. + * @calc_divs: Calculate the clock divisors. + */ +struct s3c_cpufreq_info { + const char *name; + struct s3c_freq max; + + unsigned int latency; + + unsigned int locktime_m; + unsigned int locktime_u; + unsigned char locktime_bits; + + unsigned int need_pll:1; + + /* driver routines */ + + void (*resume_clocks)(void); + + int (*get_iotiming)(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + + void (*set_iotiming)(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + + int (*calc_iotiming)(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + + int (*calc_freqtable)(struct s3c_cpufreq_config *cfg, + struct cpufreq_frequency_table *t, + size_t table_size); + + void (*debug_io_show)(struct seq_file *seq, + struct s3c_cpufreq_config *cfg, + union s3c_iobank *iob); + + void (*set_refresh)(struct s3c_cpufreq_config *cfg); + void (*set_fvco)(struct s3c_cpufreq_config *cfg); + void (*set_divs)(struct s3c_cpufreq_config *cfg); + int (*calc_divs)(struct s3c_cpufreq_config *cfg); +}; + +extern int s3c_cpufreq_register(struct s3c_cpufreq_info *info); + +extern int s3c_plltab_register(struct cpufreq_frequency_table *plls, unsigned int plls_no); + +/* exports and utilities for debugfs */ +extern struct s3c_cpufreq_config *s3c_cpufreq_getconfig(void); +extern struct s3c_iotimings *s3c_cpufreq_getiotimings(void); + +extern void s3c2410_iotiming_debugfs(struct seq_file *seq, + struct s3c_cpufreq_config *cfg, + union s3c_iobank *iob); + +extern void s3c2412_iotiming_debugfs(struct seq_file *seq, + struct s3c_cpufreq_config *cfg, + union s3c_iobank *iob); + +#ifdef CONFIG_CPU_FREQ_S3C24XX_DEBUGFS +#define s3c_cpufreq_debugfs_call(x) x +#else +#define s3c_cpufreq_debugfs_call(x) NULL +#endif + +/* Useful utility functions. */ + +extern struct clk *s3c_cpufreq_clk_get(struct device *, const char *); + +/* S3C2410 and compatible exported functions */ + +extern void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg); + +extern int s3c2410_iotiming_calc(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot); + +extern int s3c2410_iotiming_get(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + +extern void s3c2410_iotiming_set(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot); + +extern void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg); + +/* S3C2412 compatible routines */ + +extern int s3c2412_iotiming_get(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + +extern int s3c2412_iotiming_get(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings); + +extern int s3c2412_iotiming_calc(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot); + +extern void s3c2412_iotiming_set(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot); + +#ifdef CONFIG_CPU_FREQ_S3C24XX_DEBUG +#define s3c_freq_dbg(x...) printk(KERN_INFO x) +#else +#define s3c_freq_dbg(x...) do { if (0) printk(x); } while (0) +#endif /* CONFIG_CPU_FREQ_S3C24XX_DEBUG */ + +#ifdef CONFIG_CPU_FREQ_S3C24XX_IODEBUG +#define s3c_freq_iodbg(x...) printk(KERN_INFO x) +#else +#define s3c_freq_iodbg(x...) do { if (0) printk(x); } while (0) +#endif /* CONFIG_CPU_FREQ_S3C24XX_IODEBUG */ + +static inline int s3c_cpufreq_addfreq(struct cpufreq_frequency_table *table, + int index, size_t table_size, + unsigned int freq) +{ + if (index < 0) + return index; + + if (table) { + if (index >= table_size) + return -ENOMEM; + + s3c_freq_dbg("%s: { %d = %u kHz }\n", + __func__, index, freq); + + table[index].index = index; + table[index].frequency = freq; + } + + return index + 1; +} diff --git a/arch/arm/plat-s3c24xx/include/plat/s3c2410.h b/arch/arm/plat-s3c24xx/include/plat/s3c2410.h index a9ac9e29759..b6deeef8f66 100644 --- a/arch/arm/plat-s3c24xx/include/plat/s3c2410.h +++ b/arch/arm/plat-s3c24xx/include/plat/s3c2410.h @@ -14,6 +14,7 @@ #ifdef CONFIG_CPU_S3C2410 extern int s3c2410_init(void); +extern int s3c2410a_init(void); extern void s3c2410_map_io(void); diff --git a/arch/arm/plat-s3c24xx/s3c2410-cpufreq-utils.c b/arch/arm/plat-s3c24xx/s3c2410-cpufreq-utils.c new file mode 100644 index 00000000000..43ea80190d8 --- /dev/null +++ b/arch/arm/plat-s3c24xx/s3c2410-cpufreq-utils.c @@ -0,0 +1,64 @@ +/* linux/arch/arm/plat-s3c24xx/s3c2410-cpufreq-utils.c + * + * Copyright (c) 2009 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C24XX CPU Frequency scaling - utils for S3C2410/S3C2440/S3C2442 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/cpufreq.h> +#include <linux/io.h> + +#include <mach/map.h> +#include <mach/regs-mem.h> +#include <mach/regs-clock.h> + +#include <plat/cpu-freq-core.h> + +/** + * s3c2410_cpufreq_setrefresh - set SDRAM refresh value + * @cfg: The frequency configuration + * + * Set the SDRAM refresh value appropriately for the configured + * frequency. + */ +void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg) +{ + struct s3c_cpufreq_board *board = cfg->board; + unsigned long refresh; + unsigned long refval; + + /* Reduce both the refresh time (in ns) and the frequency (in MHz) + * down to ensure that we do not overflow 32 bit numbers. + * + * This should work for HCLK up to 133MHz and refresh period up + * to 30usec. + */ + + refresh = (cfg->freq.hclk / 100) * (board->refresh / 10); + refresh = DIV_ROUND_UP(refresh, (1000 * 1000)); /* apply scale */ + refresh = (1 << 11) + 1 - refresh; + + s3c_freq_dbg("%s: refresh value %lu\n", __func__, refresh); + + refval = __raw_readl(S3C2410_REFRESH); + refval &= ~((1 << 12) - 1); + refval |= refresh; + __raw_writel(refval, S3C2410_REFRESH); +} + +/** + * s3c2410_set_fvco - set the PLL value + * @cfg: The frequency configuration + */ +void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg) +{ + __raw_writel(cfg->pll.index, S3C2410_MPLLCON); +} diff --git a/arch/arm/plat-s3c24xx/s3c2410-iotiming.c b/arch/arm/plat-s3c24xx/s3c2410-iotiming.c new file mode 100644 index 00000000000..d0a3a145cd4 --- /dev/null +++ b/arch/arm/plat-s3c24xx/s3c2410-iotiming.c @@ -0,0 +1,477 @@ +/* linux/arch/arm/plat-s3c24xx/s3c2410-iotiming.c + * + * Copyright (c) 2006,2008,2009 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C24XX CPU Frequency scaling - IO timing for S3C2410/S3C2440/S3C2442 + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/cpufreq.h> +#include <linux/seq_file.h> +#include <linux/io.h> + +#include <mach/map.h> +#include <mach/regs-mem.h> +#include <mach/regs-clock.h> + +#include <plat/cpu-freq-core.h> + +#define print_ns(x) ((x) / 10), ((x) % 10) + +/** + * s3c2410_print_timing - print bank timing data for debug purposes + * @pfx: The prefix to put on the output + * @timings: The timing inforamtion to print. +*/ +static void s3c2410_print_timing(const char *pfx, + struct s3c_iotimings *timings) +{ + struct s3c2410_iobank_timing *bt; + int bank; + + for (bank = 0; bank < MAX_BANKS; bank++) { + bt = timings->bank[bank].io_2410; + if (!bt) + continue; + + printk(KERN_DEBUG "%s %d: Tacs=%d.%d, Tcos=%d.%d, Tacc=%d.%d, " + "Tcoh=%d.%d, Tcah=%d.%d\n", pfx, bank, + print_ns(bt->tacs), + print_ns(bt->tcos), + print_ns(bt->tacc), + print_ns(bt->tcoh), + print_ns(bt->tcah)); + } +} + +/** + * bank_reg - convert bank number to pointer to the control register. + * @bank: The IO bank number. + */ +static inline void __iomem *bank_reg(unsigned int bank) +{ + return S3C2410_BANKCON0 + (bank << 2); +} + +/** + * bank_is_io - test whether bank is used for IO + * @bankcon: The bank control register. + * + * This is a simplistic test to see if any BANKCON[x] is not an IO + * bank. It currently does not take into account whether BWSCON has + * an illegal width-setting in it, or if the pin connected to nCS[x] + * is actually being handled as a chip-select. + */ +static inline int bank_is_io(unsigned long bankcon) +{ + return !(bankcon & S3C2410_BANKCON_SDRAM); +} + +/** + * to_div - convert cycle time to divisor + * @cyc: The cycle time, in 10ths of nanoseconds. + * @hclk_tns: The cycle time for HCLK, in 10ths of nanoseconds. + * + * Convert the given cycle time into the divisor to use to obtain it from + * HCLK. +*/ +static inline unsigned int to_div(unsigned int cyc, unsigned int hclk_tns) +{ + if (cyc == 0) + return 0; + + return DIV_ROUND_UP(cyc, hclk_tns); +} + +/** + * calc_0124 - calculate divisor control for divisors that do /0, /1. /2 and /4 + * @cyc: The cycle time, in 10ths of nanoseconds. + * @hclk_tns: The cycle time for HCLK, in 10ths of nanoseconds. + * @v: Pointer to register to alter. + * @shift: The shift to get to the control bits. + * + * Calculate the divisor, and turn it into the correct control bits to + * set in the result, @v. + */ +static unsigned int calc_0124(unsigned int cyc, unsigned long hclk_tns, + unsigned long *v, int shift) +{ + unsigned int div = to_div(cyc, hclk_tns); + unsigned long val; + + s3c_freq_iodbg("%s: cyc=%d, hclk=%lu, shift=%d => div %d\n", + __func__, cyc, hclk_tns, shift, div); + + switch (div) { + case 0: + val = 0; + break; + case 1: + val = 1; + break; + case 2: + val = 2; + break; + case 3: + case 4: + val = 3; + break; + default: + return -1; + } + + *v |= val << shift; + return 0; +} + +int calc_tacp(unsigned int cyc, unsigned long hclk, unsigned long *v) +{ + /* Currently no support for Tacp calculations. */ + return 0; +} + +/** + * calc_tacc - calculate divisor control for tacc. + * @cyc: The cycle time, in 10ths of nanoseconds. + * @nwait_en: IS nWAIT enabled for this bank. + * @hclk_tns: The cycle time for HCLK, in 10ths of nanoseconds. + * @v: Pointer to register to alter. + * + * Calculate the divisor control for tACC, taking into account whether + * the bank has nWAIT enabled. The result is used to modify the value + * pointed to by @v. +*/ +static int calc_tacc(unsigned int cyc, int nwait_en, + unsigned long hclk_tns, unsigned long *v) +{ + unsigned int div = to_div(cyc, hclk_tns); + unsigned long val; + + s3c_freq_iodbg("%s: cyc=%u, nwait=%d, hclk=%lu => div=%u\n", + __func__, cyc, nwait_en, hclk_tns, div); + + /* if nWait enabled on an bank, Tacc must be at-least 4 cycles. */ + if (nwait_en && div < 4) + div = 4; + + switch (div) { + case 0: + val = 0; + break; + + case 1: + case 2: + case 3: + case 4: + val = div - 1; + break; + + case 5: + case 6: + val = 4; + break; + + case 7: + case 8: + val = 5; + break; + + case 9: + case 10: + val = 6; + break; + + case 11: + case 12: + case 13: + case 14: + val = 7; + break; + + default: + return -1; + } + + *v |= val << 8; + return 0; +} + +/** + * s3c2410_calc_bank - calculate bank timing infromation + * @cfg: The configuration we need to calculate for. + * @bt: The bank timing information. + * + * Given the cycle timine for a bank @bt, calculate the new BANKCON + * setting for the @cfg timing. This updates the timing information + * ready for the cpu frequency change. + */ +static int s3c2410_calc_bank(struct s3c_cpufreq_config *cfg, + struct s3c2410_iobank_timing *bt) +{ + unsigned long hclk = cfg->freq.hclk_tns; + unsigned long res; + int ret; + + res = bt->bankcon; + res &= (S3C2410_BANKCON_SDRAM | S3C2410_BANKCON_PMC16); + + /* tacp: 2,3,4,5 */ + /* tcah: 0,1,2,4 */ + /* tcoh: 0,1,2,4 */ + /* tacc: 1,2,3,4,6,7,10,14 (>4 for nwait) */ + /* tcos: 0,1,2,4 */ + /* tacs: 0,1,2,4 */ + + ret = calc_0124(bt->tacs, hclk, &res, S3C2410_BANKCON_Tacs_SHIFT); + ret |= calc_0124(bt->tcos, hclk, &res, S3C2410_BANKCON_Tcos_SHIFT); + ret |= calc_0124(bt->tcah, hclk, &res, S3C2410_BANKCON_Tcah_SHIFT); + ret |= calc_0124(bt->tcoh, hclk, &res, S3C2410_BANKCON_Tcoh_SHIFT); + + if (ret) + return -EINVAL; + + ret |= calc_tacp(bt->tacp, hclk, &res); + ret |= calc_tacc(bt->tacc, bt->nwait_en, hclk, &res); + + if (ret) + return -EINVAL; + + bt->bankcon = res; + return 0; +} + +static unsigned int tacc_tab[] = { + [0] = 1, + [1] = 2, + [2] = 3, + [3] = 4, + [4] = 6, + [5] = 9, + [6] = 10, + [7] = 14, +}; + +/** + * get_tacc - turn tACC value into cycle time + * @hclk_tns: The cycle time for HCLK, in 10ths of nanoseconds. + * @val: The bank timing register value, shifed down. + */ +static unsigned int get_tacc(unsigned long hclk_tns, + unsigned long val) +{ + val &= 7; + return hclk_tns * tacc_tab[val]; +} + +/** + * get_0124 - turn 0/1/2/4 divider into cycle time + * @hclk_tns: The cycle time for HCLK, in 10ths of nanoseconds. + * @val: The bank timing register value, shifed down. + */ +static unsigned int get_0124(unsigned long hclk_tns, + unsigned long val) +{ + val &= 3; + return hclk_tns * ((val == 3) ? 4 : val); +} + +/** + * s3c2410_iotiming_getbank - turn BANKCON into cycle time information + * @cfg: The frequency configuration + * @bt: The bank timing to fill in (uses cached BANKCON) + * + * Given the BANKCON setting in @bt and the current frequency settings + * in @cfg, update the cycle timing information. + */ +void s3c2410_iotiming_getbank(struct s3c_cpufreq_config *cfg, + struct s3c2410_iobank_timing *bt) +{ + unsigned long bankcon = bt->bankcon; + unsigned long hclk = cfg->freq.hclk_tns; + + bt->tcah = get_0124(hclk, bankcon >> S3C2410_BANKCON_Tcah_SHIFT); + bt->tcoh = get_0124(hclk, bankcon >> S3C2410_BANKCON_Tcoh_SHIFT); + bt->tcos = get_0124(hclk, bankcon >> S3C2410_BANKCON_Tcos_SHIFT); + bt->tacs = get_0124(hclk, bankcon >> S3C2410_BANKCON_Tacs_SHIFT); + bt->tacc = get_tacc(hclk, bankcon >> S3C2410_BANKCON_Tacc_SHIFT); +} + +/** + * s3c2410_iotiming_debugfs - debugfs show io bank timing information + * @seq: The seq_file to write output to using seq_printf(). + * @cfg: The current configuration. + * @iob: The IO bank information to decode. + */ +void s3c2410_iotiming_debugfs(struct seq_file *seq, + struct s3c_cpufreq_config *cfg, + union s3c_iobank *iob) +{ + struct s3c2410_iobank_timing *bt = iob->io_2410; + unsigned long bankcon = bt->bankcon; + unsigned long hclk = cfg->freq.hclk_tns; + unsigned int tacs; + unsigned int tcos; + unsigned int tacc; + unsigned int tcoh; + unsigned int tcah; + + seq_printf(seq, "BANKCON=0x%08lx\n", bankcon); + + tcah = get_0124(hclk, bankcon >> S3C2410_BANKCON_Tcah_SHIFT); + tcoh = get_0124(hclk, bankcon >> S3C2410_BANKCON_Tcoh_SHIFT); + tcos = get_0124(hclk, bankcon >> S3C2410_BANKCON_Tcos_SHIFT); + tacs = get_0124(hclk, bankcon >> S3C2410_BANKCON_Tacs_SHIFT); + tacc = get_tacc(hclk, bankcon >> S3C2410_BANKCON_Tacc_SHIFT); + + seq_printf(seq, + "\tRead: Tacs=%d.%d, Tcos=%d.%d, Tacc=%d.%d, Tcoh=%d.%d, Tcah=%d.%d\n", + print_ns(bt->tacs), + print_ns(bt->tcos), + print_ns(bt->tacc), + print_ns(bt->tcoh), + print_ns(bt->tcah)); + + seq_printf(seq, + "\t Set: Tacs=%d.%d, Tcos=%d.%d, Tacc=%d.%d, Tcoh=%d.%d, Tcah=%d.%d\n", + print_ns(tacs), + print_ns(tcos), + print_ns(tacc), + print_ns(tcoh), + print_ns(tcah)); +} + +/** + * s3c2410_iotiming_calc - Calculate bank timing for frequency change. + * @cfg: The frequency configuration + * @iot: The IO timing information to fill out. + * + * Calculate the new values for the banks in @iot based on the new + * frequency information in @cfg. This is then used by s3c2410_iotiming_set() + * to update the timing when necessary. + */ +int s3c2410_iotiming_calc(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot) +{ + struct s3c2410_iobank_timing *bt; + unsigned long bankcon; + int bank; + int ret; + + for (bank = 0; bank < MAX_BANKS; bank++) { + bankcon = __raw_readl(bank_reg(bank)); + bt = iot->bank[bank].io_2410; + + if (!bt) + continue; + + bt->bankcon = bankcon; + + ret = s3c2410_calc_bank(cfg, bt); + if (ret) { + printk(KERN_ERR "%s: cannot calculate bank %d io\n", + __func__, bank); + goto err; + } + + s3c_freq_iodbg("%s: bank %d: con=%08lx\n", + __func__, bank, bt->bankcon); + } + + return 0; + err: + return ret; +} + +/** + * s3c2410_iotiming_set - set the IO timings from the given setup. + * @cfg: The frequency configuration + * @iot: The IO timing information to use. + * + * Set all the currently used IO bank timing information generated + * by s3c2410_iotiming_calc() once the core has validated that all + * the new values are within permitted bounds. + */ +void s3c2410_iotiming_set(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot) +{ + struct s3c2410_iobank_timing *bt; + int bank; + + /* set the io timings from the specifier */ + + for (bank = 0; bank < MAX_BANKS; bank++) { + bt = iot->bank[bank].io_2410; + if (!bt) + continue; + + __raw_writel(bt->bankcon, bank_reg(bank)); + } +} + +/** + * s3c2410_iotiming_get - Get the timing information from current registers. + * @cfg: The frequency configuration + * @timings: The IO timing information to fill out. + * + * Calculate the @timings timing information from the current frequency + * information in @cfg, and the new frequency configur + * through all the IO banks, reading the state and then updating @iot + * as necessary. + * + * This is used at the moment on initialisation to get the current + * configuration so that boards do not have to carry their own setup + * if the timings are correct on initialisation. + */ + +int s3c2410_iotiming_get(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings) +{ + struct s3c2410_iobank_timing *bt; + unsigned long bankcon; + unsigned long bwscon; + int bank; + + bwscon = __raw_readl(S3C2410_BWSCON); + + /* look through all banks to see what is currently set. */ + + for (bank = 0; bank < MAX_BANKS; bank++) { + bankcon = __raw_readl(bank_reg(bank)); + + if (!bank_is_io(bankcon)) + continue; + + s3c_freq_iodbg("%s: bank %d: con %08lx\n", + __func__, bank, bankcon); + + bt = kzalloc(sizeof(struct s3c2410_iobank_timing), GFP_KERNEL); + if (!bt) { + printk(KERN_ERR "%s: no memory for bank\n", __func__); + return -ENOMEM; + } + + /* find out in nWait is enabled for bank. */ + + if (bank != 0) { + unsigned long tmp = S3C2410_BWSCON_GET(bwscon, bank); + if (tmp & S3C2410_BWSCON_WS) + bt->nwait_en = 1; + } + + timings->bank[bank].io_2410 = bt; + bt->bankcon = bankcon; + + s3c2410_iotiming_getbank(cfg, bt); + } + + s3c2410_print_timing("get", timings); + return 0; +} diff --git a/arch/arm/plat-s3c24xx/s3c2412-iotiming.c b/arch/arm/plat-s3c24xx/s3c2412-iotiming.c new file mode 100644 index 00000000000..fd45e47facb --- /dev/null +++ b/arch/arm/plat-s3c24xx/s3c2412-iotiming.c @@ -0,0 +1,285 @@ +/* linux/arch/arm/plat-s3c24xx/s3c2412-iotiming.c + * + * Copyright (c) 2006,2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * + * S3C2412/S3C2443 (PL093 based) IO timing support + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/cpufreq.h> +#include <linux/seq_file.h> +#include <linux/sysdev.h> +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/err.h> + +#include <linux/amba/pl093.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <mach/regs-s3c2412-mem.h> + +#include <plat/cpu.h> +#include <plat/cpu-freq-core.h> +#include <plat/clock.h> + +#define print_ns(x) ((x) / 10), ((x) % 10) + +/** + * s3c2412_print_timing - print timing infromation via printk. + * @pfx: The prefix to print each line with. + * @iot: The IO timing information + */ +static void s3c2412_print_timing(const char *pfx, struct s3c_iotimings *iot) +{ + struct s3c2412_iobank_timing *bt; + unsigned int bank; + + for (bank = 0; bank < MAX_BANKS; bank++) { + bt = iot->bank[bank].io_2412; + if (!bt) + continue; + + printk(KERN_DEBUG "%s: %d: idcy=%d.%d wstrd=%d.%d wstwr=%d,%d" + "wstoen=%d.%d wstwen=%d.%d wstbrd=%d.%d\n", pfx, bank, + print_ns(bt->idcy), + print_ns(bt->wstrd), + print_ns(bt->wstwr), + print_ns(bt->wstoen), + print_ns(bt->wstwen), + print_ns(bt->wstbrd)); + } +} + +/** + * to_div - turn a cycle length into a divisor setting. + * @cyc_tns: The cycle time in 10ths of nanoseconds. + * @clk_tns: The clock period in 10ths of nanoseconds. + */ +static inline unsigned int to_div(unsigned int cyc_tns, unsigned int clk_tns) +{ + return cyc_tns ? DIV_ROUND_UP(cyc_tns, clk_tns) : 0; +} + +/** + * calc_timing - calculate timing divisor value and check in range. + * @hwtm: The hardware timing in 10ths of nanoseconds. + * @clk_tns: The clock period in 10ths of nanoseconds. + * @err: Pointer to err variable to update in event of failure. + */ +static unsigned int calc_timing(unsigned int hwtm, unsigned int clk_tns, + unsigned int *err) +{ + unsigned int ret = to_div(hwtm, clk_tns); + + if (ret > 0xf) + *err = -EINVAL; + + return ret; +} + +/** + * s3c2412_calc_bank - calculate the bank divisor settings. + * @cfg: The current frequency configuration. + * @bt: The bank timing. + */ +static int s3c2412_calc_bank(struct s3c_cpufreq_config *cfg, + struct s3c2412_iobank_timing *bt) +{ + unsigned int hclk = cfg->freq.hclk_tns; + int err = 0; + + bt->smbidcyr = calc_timing(bt->idcy, hclk, &err); + bt->smbwstrd = calc_timing(bt->wstrd, hclk, &err); + bt->smbwstwr = calc_timing(bt->wstwr, hclk, &err); + bt->smbwstoen = calc_timing(bt->wstoen, hclk, &err); + bt->smbwstwen = calc_timing(bt->wstwen, hclk, &err); + bt->smbwstbrd = calc_timing(bt->wstbrd, hclk, &err); + + return err; +} + +/** + * s3c2412_iotiming_debugfs - debugfs show io bank timing information + * @seq: The seq_file to write output to using seq_printf(). + * @cfg: The current configuration. + * @iob: The IO bank information to decode. +*/ +void s3c2412_iotiming_debugfs(struct seq_file *seq, + struct s3c_cpufreq_config *cfg, + union s3c_iobank *iob) +{ + struct s3c2412_iobank_timing *bt = iob->io_2412; + + seq_printf(seq, + "\tRead: idcy=%d.%d wstrd=%d.%d wstwr=%d,%d" + "wstoen=%d.%d wstwen=%d.%d wstbrd=%d.%d\n", + print_ns(bt->idcy), + print_ns(bt->wstrd), + print_ns(bt->wstwr), + print_ns(bt->wstoen), + print_ns(bt->wstwen), + print_ns(bt->wstbrd)); +} + +/** + * s3c2412_iotiming_calc - calculate all the bank divisor settings. + * @cfg: The current frequency configuration. + * @iot: The bank timing information. + * + * Calculate the timing information for all the banks that are + * configured as IO, using s3c2412_calc_bank(). + */ +int s3c2412_iotiming_calc(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot) +{ + struct s3c2412_iobank_timing *bt; + int bank; + int ret; + + for (bank = 0; bank < MAX_BANKS; bank++) { + bt = iot->bank[bank].io_2412; + if (!bt) + continue; + + ret = s3c2412_calc_bank(cfg, bt); + if (ret) { + printk(KERN_ERR "%s: cannot calculate bank %d io\n", + __func__, bank); + goto err; + } + } + + return 0; + err: + return ret; +} + +/** + * s3c2412_iotiming_set - set the timing information + * @cfg: The current frequency configuration. + * @iot: The bank timing information. + * + * Set the IO bank information from the details calculated earlier from + * calling s3c2412_iotiming_calc(). + */ +void s3c2412_iotiming_set(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *iot) +{ + struct s3c2412_iobank_timing *bt; + void __iomem *regs; + int bank; + + /* set the io timings from the specifier */ + + for (bank = 0; bank < MAX_BANKS; bank++) { + bt = iot->bank[bank].io_2412; + if (!bt) + continue; + + regs = S3C2412_SSMC_BANK(bank); + + __raw_writel(bt->smbidcyr, regs + SMBIDCYR); + __raw_writel(bt->smbwstrd, regs + SMBWSTRDR); + __raw_writel(bt->smbwstwr, regs + SMBWSTWRR); + __raw_writel(bt->smbwstoen, regs + SMBWSTOENR); + __raw_writel(bt->smbwstwen, regs + SMBWSTWENR); + __raw_writel(bt->smbwstbrd, regs + SMBWSTBRDR); + } +} + +static inline unsigned int s3c2412_decode_timing(unsigned int clock, u32 reg) +{ + return (reg & 0xf) * clock; +} + +static void s3c2412_iotiming_getbank(struct s3c_cpufreq_config *cfg, + struct s3c2412_iobank_timing *bt, + unsigned int bank) +{ + unsigned long clk = cfg->freq.hclk_tns; /* ssmc clock??? */ + void __iomem *regs = S3C2412_SSMC_BANK(bank); + + bt->idcy = s3c2412_decode_timing(clk, __raw_readl(regs + SMBIDCYR)); + bt->wstrd = s3c2412_decode_timing(clk, __raw_readl(regs + SMBWSTRDR)); + bt->wstoen = s3c2412_decode_timing(clk, __raw_readl(regs + SMBWSTOENR)); + bt->wstwen = s3c2412_decode_timing(clk, __raw_readl(regs + SMBWSTWENR)); + bt->wstbrd = s3c2412_decode_timing(clk, __raw_readl(regs + SMBWSTBRDR)); +} + +/** + * bank_is_io - return true if bank is (possibly) IO. + * @bank: The bank number. + * @bankcfg: The value of S3C2412_EBI_BANKCFG. + */ +static inline bool bank_is_io(unsigned int bank, u32 bankcfg) +{ + if (bank < 2) + return true; + + return !(bankcfg & (1 << bank)); +} + +int s3c2412_iotiming_get(struct s3c_cpufreq_config *cfg, + struct s3c_iotimings *timings) +{ + struct s3c2412_iobank_timing *bt; + u32 bankcfg = __raw_readl(S3C2412_EBI_BANKCFG); + unsigned int bank; + + /* look through all banks to see what is currently set. */ + + for (bank = 0; bank < MAX_BANKS; bank++) { + if (!bank_is_io(bank, bankcfg)) + continue; + + bt = kzalloc(sizeof(struct s3c2412_iobank_timing), GFP_KERNEL); + if (!bt) { + printk(KERN_ERR "%s: no memory for bank\n", __func__); + return -ENOMEM; + } + + timings->bank[bank].io_2412 = bt; + s3c2412_iotiming_getbank(cfg, bt, bank); + } + + s3c2412_print_timing("get", timings); + return 0; +} + +/* this is in here as it is so small, it doesn't currently warrant a file + * to itself. We expect that any s3c24xx needing this is going to also + * need the iotiming support. + */ +void s3c2412_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg) +{ + struct s3c_cpufreq_board *board = cfg->board; + u32 refresh; + + WARN_ON(board == NULL); + + /* Reduce both the refresh time (in ns) and the frequency (in MHz) + * down to ensure that we do not overflow 32 bit numbers. + * + * This should work for HCLK up to 133MHz and refresh period up + * to 30usec. + */ + + refresh = (cfg->freq.hclk / 100) * (board->refresh / 10); + refresh = DIV_ROUND_UP(refresh, (1000 * 1000)); /* apply scale */ + refresh &= ((1 << 16) - 1); + + s3c_freq_dbg("%s: refresh value %u\n", __func__, (unsigned int)refresh); + + __raw_writel(refresh, S3C2412_REFRESH); +} diff --git a/arch/arm/plat-s3c24xx/s3c2440-cpufreq.c b/arch/arm/plat-s3c24xx/s3c2440-cpufreq.c new file mode 100644 index 00000000000..ae2e6c604f2 --- /dev/null +++ b/arch/arm/plat-s3c24xx/s3c2440-cpufreq.c @@ -0,0 +1,311 @@ +/* linux/arch/arm/plat-s3c24xx/s3c2440-cpufreq.c + * + * Copyright (c) 2006,2008,2009 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * Vincent Sanders <vince@simtec.co.uk> + * + * S3C2440/S3C2442 CPU Frequency scaling + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/cpufreq.h> +#include <linux/sysdev.h> +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> + +#include <mach/hardware.h> + +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <mach/regs-clock.h> + +#include <plat/cpu.h> +#include <plat/cpu-freq-core.h> +#include <plat/clock.h> + +static struct clk *xtal; +static struct clk *fclk; +static struct clk *hclk; +static struct clk *armclk; + +/* HDIV: 1, 2, 3, 4, 6, 8 */ + +static inline int within_khz(unsigned long a, unsigned long b) +{ + long diff = a - b; + + return (diff >= -1000 && diff <= 1000); +} + +/** + * s3c2440_cpufreq_calcdivs - calculate divider settings + * @cfg: The cpu frequency settings. + * + * Calcualte the divider values for the given frequency settings + * specified in @cfg. The values are stored in @cfg for later use + * by the relevant set routine if the request settings can be reached. + */ +int s3c2440_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg) +{ + unsigned int hdiv, pdiv; + unsigned long hclk, fclk, armclk; + unsigned long hclk_max; + + fclk = cfg->freq.fclk; + armclk = cfg->freq.armclk; + hclk_max = cfg->max.hclk; + + s3c_freq_dbg("%s: fclk is %lu, armclk %lu, max hclk %lu\n", + __func__, fclk, armclk, hclk_max); + + if (armclk > fclk) { + printk(KERN_WARNING "%s: armclk > fclk\n", __func__); + armclk = fclk; + } + + /* if we are in DVS, we need HCLK to be <= ARMCLK */ + if (armclk < fclk && armclk < hclk_max) + hclk_max = armclk; + + for (hdiv = 1; hdiv < 9; hdiv++) { + if (hdiv == 5 || hdiv == 7) + hdiv++; + + hclk = (fclk / hdiv); + if (hclk <= hclk_max || within_khz(hclk, hclk_max)) + break; + } + + s3c_freq_dbg("%s: hclk %lu, div %d\n", __func__, hclk, hdiv); + + if (hdiv > 8) + goto invalid; + + pdiv = (hclk > cfg->max.pclk) ? 2 : 1; + + if ((hclk / pdiv) > cfg->max.pclk) + pdiv++; + + s3c_freq_dbg("%s: pdiv %d\n", __func__, pdiv); + + if (pdiv > 2) + goto invalid; + + pdiv *= hdiv; + + /* calculate a valid armclk */ + + if (armclk < hclk) + armclk = hclk; + + /* if we're running armclk lower than fclk, this really means + * that the system should go into dvs mode, which means that + * armclk is connected to hclk. */ + if (armclk < fclk) { + cfg->divs.dvs = 1; + armclk = hclk; + } else + cfg->divs.dvs = 0; + + cfg->freq.armclk = armclk; + + /* store the result, and then return */ + + cfg->divs.h_divisor = hdiv; + cfg->divs.p_divisor = pdiv; + + return 0; + + invalid: + return -EINVAL; +} + +#define CAMDIVN_HCLK_HALF (S3C2440_CAMDIVN_HCLK3_HALF | \ + S3C2440_CAMDIVN_HCLK4_HALF) + +/** + * s3c2440_cpufreq_setdivs - set the cpu frequency divider settings + * @cfg: The cpu frequency settings. + * + * Set the divisors from the settings in @cfg, which where generated + * during the calculation phase by s3c2440_cpufreq_calcdivs(). + */ +static void s3c2440_cpufreq_setdivs(struct s3c_cpufreq_config *cfg) +{ + unsigned long clkdiv, camdiv; + + s3c_freq_dbg("%s: divsiors: h=%d, p=%d\n", __func__, + cfg->divs.h_divisor, cfg->divs.p_divisor); + + clkdiv = __raw_readl(S3C2410_CLKDIVN); + camdiv = __raw_readl(S3C2440_CAMDIVN); + + clkdiv &= ~(S3C2440_CLKDIVN_HDIVN_MASK | S3C2440_CLKDIVN_PDIVN); + camdiv &= ~CAMDIVN_HCLK_HALF; + + switch (cfg->divs.h_divisor) { + case 1: + clkdiv |= S3C2440_CLKDIVN_HDIVN_1; + break; + + case 2: + clkdiv |= S3C2440_CLKDIVN_HDIVN_2; + break; + + case 6: + camdiv |= S3C2440_CAMDIVN_HCLK3_HALF; + case 3: + clkdiv |= S3C2440_CLKDIVN_HDIVN_3_6; + break; + + case 8: + camdiv |= S3C2440_CAMDIVN_HCLK4_HALF; + case 4: + clkdiv |= S3C2440_CLKDIVN_HDIVN_4_8; + break; + + default: + BUG(); /* we don't expect to get here. */ + } + + if (cfg->divs.p_divisor != cfg->divs.h_divisor) + clkdiv |= S3C2440_CLKDIVN_PDIVN; + + /* todo - set pclk. */ + + /* Write the divisors first with hclk intentionally halved so that + * when we write clkdiv we will under-frequency instead of over. We + * then make a short delay and remove the hclk halving if necessary. + */ + + __raw_writel(camdiv | CAMDIVN_HCLK_HALF, S3C2440_CAMDIVN); + __raw_writel(clkdiv, S3C2410_CLKDIVN); + + ndelay(20); + __raw_writel(camdiv, S3C2440_CAMDIVN); + + clk_set_parent(armclk, cfg->divs.dvs ? hclk : fclk); +} + +static int run_freq_for(unsigned long max_hclk, unsigned long fclk, + int *divs, + struct cpufreq_frequency_table *table, + size_t table_size) +{ + unsigned long freq; + int index = 0; + int div; + + for (div = *divs; div > 0; div = *divs++) { + freq = fclk / div; + + if (freq > max_hclk && div != 1) + continue; + + freq /= 1000; /* table is in kHz */ + index = s3c_cpufreq_addfreq(table, index, table_size, freq); + if (index < 0) + break; + } + + return index; +} + +static int hclk_divs[] = { 1, 2, 3, 4, 6, 8, -1 }; + +static int s3c2440_cpufreq_calctable(struct s3c_cpufreq_config *cfg, + struct cpufreq_frequency_table *table, + size_t table_size) +{ + int ret; + + WARN_ON(cfg->info == NULL); + WARN_ON(cfg->board == NULL); + + ret = run_freq_for(cfg->info->max.hclk, + cfg->info->max.fclk, + hclk_divs, + table, table_size); + + s3c_freq_dbg("%s: returning %d\n", __func__, ret); + + return ret; +} + +struct s3c_cpufreq_info s3c2440_cpufreq_info = { + .max = { + .fclk = 400000000, + .hclk = 133333333, + .pclk = 66666666, + }, + + .locktime_m = 300, + .locktime_u = 300, + .locktime_bits = 16, + + .name = "s3c244x", + .calc_iotiming = s3c2410_iotiming_calc, + .set_iotiming = s3c2410_iotiming_set, + .get_iotiming = s3c2410_iotiming_get, + .set_fvco = s3c2410_set_fvco, + + .set_refresh = s3c2410_cpufreq_setrefresh, + .set_divs = s3c2440_cpufreq_setdivs, + .calc_divs = s3c2440_cpufreq_calcdivs, + .calc_freqtable = s3c2440_cpufreq_calctable, + + .resume_clocks = s3c244x_setup_clocks, + + .debug_io_show = s3c_cpufreq_debugfs_call(s3c2410_iotiming_debugfs), +}; + +static int s3c2440_cpufreq_add(struct sys_device *sysdev) +{ + xtal = s3c_cpufreq_clk_get(NULL, "xtal"); + hclk = s3c_cpufreq_clk_get(NULL, "hclk"); + fclk = s3c_cpufreq_clk_get(NULL, "fclk"); + armclk = s3c_cpufreq_clk_get(NULL, "armclk"); + + if (IS_ERR(xtal) || IS_ERR(hclk) || IS_ERR(fclk) || IS_ERR(armclk)) { + printk(KERN_ERR "%s: failed to get clocks\n", __func__); + return -ENOENT; + } + + return s3c_cpufreq_register(&s3c2440_cpufreq_info); +} + +static struct sysdev_driver s3c2440_cpufreq_driver = { + .add = s3c2440_cpufreq_add, +}; + +static int s3c2440_cpufreq_init(void) +{ + return sysdev_driver_register(&s3c2440_sysclass, + &s3c2440_cpufreq_driver); +} + +/* arch_initcall adds the clocks we need, so use subsys_initcall. */ +subsys_initcall(s3c2440_cpufreq_init); + +static struct sysdev_driver s3c2442_cpufreq_driver = { + .add = s3c2440_cpufreq_add, +}; + +static int s3c2442_cpufreq_init(void) +{ + return sysdev_driver_register(&s3c2442_sysclass, + &s3c2442_cpufreq_driver); +} + +subsys_initcall(s3c2442_cpufreq_init); diff --git a/arch/arm/plat-s3c24xx/s3c2440-pll-12000000.c b/arch/arm/plat-s3c24xx/s3c2440-pll-12000000.c new file mode 100644 index 00000000000..ff9443b233a --- /dev/null +++ b/arch/arm/plat-s3c24xx/s3c2440-pll-12000000.c @@ -0,0 +1,97 @@ +/* arch/arm/plat-s3c24xx/s3c2440-pll-12000000.c + * + * Copyright (c) 2006,2007 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * Vincent Sanders <vince@arm.linux.org.uk> + * + * S3C2440/S3C2442 CPU PLL tables (12MHz Crystal) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/sysdev.h> +#include <linux/clk.h> +#include <linux/err.h> + +#include <plat/cpu.h> +#include <plat/cpu-freq-core.h> + +static struct cpufreq_frequency_table s3c2440_plls_12[] __initdata = { + { .frequency = 75000000, .index = PLLVAL(0x75, 3, 3), }, /* FVco 600.000000 */ + { .frequency = 80000000, .index = PLLVAL(0x98, 4, 3), }, /* FVco 640.000000 */ + { .frequency = 90000000, .index = PLLVAL(0x70, 2, 3), }, /* FVco 720.000000 */ + { .frequency = 100000000, .index = PLLVAL(0x5c, 1, 3), }, /* FVco 800.000000 */ + { .frequency = 110000000, .index = PLLVAL(0x66, 1, 3), }, /* FVco 880.000000 */ + { .frequency = 120000000, .index = PLLVAL(0x70, 1, 3), }, /* FVco 960.000000 */ + { .frequency = 150000000, .index = PLLVAL(0x75, 3, 2), }, /* FVco 600.000000 */ + { .frequency = 160000000, .index = PLLVAL(0x98, 4, 2), }, /* FVco 640.000000 */ + { .frequency = 170000000, .index = PLLVAL(0x4d, 1, 2), }, /* FVco 680.000000 */ + { .frequency = 180000000, .index = PLLVAL(0x70, 2, 2), }, /* FVco 720.000000 */ + { .frequency = 190000000, .index = PLLVAL(0x57, 1, 2), }, /* FVco 760.000000 */ + { .frequency = 200000000, .index = PLLVAL(0x5c, 1, 2), }, /* FVco 800.000000 */ + { .frequency = 210000000, .index = PLLVAL(0x84, 2, 2), }, /* FVco 840.000000 */ + { .frequency = 220000000, .index = PLLVAL(0x66, 1, 2), }, /* FVco 880.000000 */ + { .frequency = 230000000, .index = PLLVAL(0x6b, 1, 2), }, /* FVco 920.000000 */ + { .frequency = 240000000, .index = PLLVAL(0x70, 1, 2), }, /* FVco 960.000000 */ + { .frequency = 300000000, .index = PLLVAL(0x75, 3, 1), }, /* FVco 600.000000 */ + { .frequency = 310000000, .index = PLLVAL(0x93, 4, 1), }, /* FVco 620.000000 */ + { .frequency = 320000000, .index = PLLVAL(0x98, 4, 1), }, /* FVco 640.000000 */ + { .frequency = 330000000, .index = PLLVAL(0x66, 2, 1), }, /* FVco 660.000000 */ + { .frequency = 340000000, .index = PLLVAL(0x4d, 1, 1), }, /* FVco 680.000000 */ + { .frequency = 350000000, .index = PLLVAL(0xa7, 4, 1), }, /* FVco 700.000000 */ + { .frequency = 360000000, .index = PLLVAL(0x70, 2, 1), }, /* FVco 720.000000 */ + { .frequency = 370000000, .index = PLLVAL(0xb1, 4, 1), }, /* FVco 740.000000 */ + { .frequency = 380000000, .index = PLLVAL(0x57, 1, 1), }, /* FVco 760.000000 */ + { .frequency = 390000000, .index = PLLVAL(0x7a, 2, 1), }, /* FVco 780.000000 */ + { .frequency = 400000000, .index = PLLVAL(0x5c, 1, 1), }, /* FVco 800.000000 */ +}; + +static int s3c2440_plls12_add(struct sys_device *dev) +{ + struct clk *xtal_clk; + unsigned long xtal; + + xtal_clk = clk_get(NULL, "xtal"); + if (IS_ERR(xtal_clk)) + return PTR_ERR(xtal_clk); + + xtal = clk_get_rate(xtal_clk); + clk_put(xtal_clk); + + if (xtal == 12000000) { + printk(KERN_INFO "Using PLL table for 12MHz crystal\n"); + return s3c_plltab_register(s3c2440_plls_12, + ARRAY_SIZE(s3c2440_plls_12)); + } + + return 0; +} + +static struct sysdev_driver s3c2440_plls12_drv = { + .add = s3c2440_plls12_add, +}; + +static int __init s3c2440_pll_12mhz(void) +{ + return sysdev_driver_register(&s3c2440_sysclass, &s3c2440_plls12_drv); + +} + +arch_initcall(s3c2440_pll_12mhz); + +static struct sysdev_driver s3c2442_plls12_drv = { + .add = s3c2440_plls12_add, +}; + +static int __init s3c2442_pll_12mhz(void) +{ + return sysdev_driver_register(&s3c2442_sysclass, &s3c2442_plls12_drv); + +} + +arch_initcall(s3c2442_pll_12mhz); diff --git a/arch/arm/plat-s3c24xx/s3c2440-pll-16934400.c b/arch/arm/plat-s3c24xx/s3c2440-pll-16934400.c new file mode 100644 index 00000000000..7679af13a94 --- /dev/null +++ b/arch/arm/plat-s3c24xx/s3c2440-pll-16934400.c @@ -0,0 +1,127 @@ +/* arch/arm/plat-s3c24xx/s3c2440-pll-16934400.c + * + * Copyright (c) 2006-2008 Simtec Electronics + * http://armlinux.simtec.co.uk/ + * Ben Dooks <ben@simtec.co.uk> + * Vincent Sanders <vince@arm.linux.org.uk> + * + * S3C2440/S3C2442 CPU PLL tables (16.93444MHz Crystal) + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include <linux/types.h> +#include <linux/kernel.h> +#include <linux/sysdev.h> +#include <linux/clk.h> +#include <linux/err.h> + +#include <plat/cpu.h> +#include <plat/cpu-freq-core.h> + +static struct cpufreq_frequency_table s3c2440_plls_169344[] __initdata = { + { .frequency = 78019200, .index = PLLVAL(121, 5, 3), }, /* FVco 624.153600 */ + { .frequency = 84067200, .index = PLLVAL(131, 5, 3), }, /* FVco 672.537600 */ + { .frequency = 90115200, .index = PLLVAL(141, 5, 3), }, /* FVco 720.921600 */ + { .frequency = 96163200, .index = PLLVAL(151, 5, 3), }, /* FVco 769.305600 */ + { .frequency = 102135600, .index = PLLVAL(185, 6, 3), }, /* FVco 817.084800 */ + { .frequency = 108259200, .index = PLLVAL(171, 5, 3), }, /* FVco 866.073600 */ + { .frequency = 114307200, .index = PLLVAL(127, 3, 3), }, /* FVco 914.457600 */ + { .frequency = 120234240, .index = PLLVAL(134, 3, 3), }, /* FVco 961.873920 */ + { .frequency = 126161280, .index = PLLVAL(141, 3, 3), }, /* FVco 1009.290240 */ + { .frequency = 132088320, .index = PLLVAL(148, 3, 3), }, /* FVco 1056.706560 */ + { .frequency = 138015360, .index = PLLVAL(155, 3, 3), }, /* FVco 1104.122880 */ + { .frequency = 144789120, .index = PLLVAL(163, 3, 3), }, /* FVco 1158.312960 */ + { .frequency = 150100363, .index = PLLVAL(187, 9, 2), }, /* FVco 600.401454 */ + { .frequency = 156038400, .index = PLLVAL(121, 5, 2), }, /* FVco 624.153600 */ + { .frequency = 162086400, .index = PLLVAL(126, 5, 2), }, /* FVco 648.345600 */ + { .frequency = 168134400, .index = PLLVAL(131, 5, 2), }, /* FVco 672.537600 */ + { .frequency = 174048000, .index = PLLVAL(177, 7, 2), }, /* FVco 696.192000 */ + { .frequency = 180230400, .index = PLLVAL(141, 5, 2), }, /* FVco 720.921600 */ + { .frequency = 186278400, .index = PLLVAL(124, 4, 2), }, /* FVco 745.113600 */ + { .frequency = 192326400, .index = PLLVAL(151, 5, 2), }, /* FVco 769.305600 */ + { .frequency = 198132480, .index = PLLVAL(109, 3, 2), }, /* FVco 792.529920 */ + { .frequency = 204271200, .index = PLLVAL(185, 6, 2), }, /* FVco 817.084800 */ + { .frequency = 210268800, .index = PLLVAL(141, 4, 2), }, /* FVco 841.075200 */ + { .frequency = 216518400, .index = PLLVAL(171, 5, 2), }, /* FVco 866.073600 */ + { .frequency = 222264000, .index = PLLVAL(97, 2, 2), }, /* FVco 889.056000 */ + { .frequency = 228614400, .index = PLLVAL(127, 3, 2), }, /* FVco 914.457600 */ + { .frequency = 234259200, .index = PLLVAL(158, 4, 2), }, /* FVco 937.036800 */ + { .frequency = 240468480, .index = PLLVAL(134, 3, 2), }, /* FVco 961.873920 */ + { .frequency = 246960000, .index = PLLVAL(167, 4, 2), }, /* FVco 987.840000 */ + { .frequency = 252322560, .index = PLLVAL(141, 3, 2), }, /* FVco 1009.290240 */ + { .frequency = 258249600, .index = PLLVAL(114, 2, 2), }, /* FVco 1032.998400 */ + { .frequency = 264176640, .index = PLLVAL(148, 3, 2), }, /* FVco 1056.706560 */ + { .frequency = 270950400, .index = PLLVAL(120, 2, 2), }, /* FVco 1083.801600 */ + { .frequency = 276030720, .index = PLLVAL(155, 3, 2), }, /* FVco 1104.122880 */ + { .frequency = 282240000, .index = PLLVAL(92, 1, 2), }, /* FVco 1128.960000 */ + { .frequency = 289578240, .index = PLLVAL(163, 3, 2), }, /* FVco 1158.312960 */ + { .frequency = 294235200, .index = PLLVAL(131, 2, 2), }, /* FVco 1176.940800 */ + { .frequency = 300200727, .index = PLLVAL(187, 9, 1), }, /* FVco 600.401454 */ + { .frequency = 306358690, .index = PLLVAL(191, 9, 1), }, /* FVco 612.717380 */ + { .frequency = 312076800, .index = PLLVAL(121, 5, 1), }, /* FVco 624.153600 */ + { .frequency = 318366720, .index = PLLVAL(86, 3, 1), }, /* FVco 636.733440 */ + { .frequency = 324172800, .index = PLLVAL(126, 5, 1), }, /* FVco 648.345600 */ + { .frequency = 330220800, .index = PLLVAL(109, 4, 1), }, /* FVco 660.441600 */ + { .frequency = 336268800, .index = PLLVAL(131, 5, 1), }, /* FVco 672.537600 */ + { .frequency = 342074880, .index = PLLVAL(93, 3, 1), }, /* FVco 684.149760 */ + { .frequency = 348096000, .index = PLLVAL(177, 7, 1), }, /* FVco 696.192000 */ + { .frequency = 355622400, .index = PLLVAL(118, 4, 1), }, /* FVco 711.244800 */ + { .frequency = 360460800, .index = PLLVAL(141, 5, 1), }, /* FVco 720.921600 */ + { .frequency = 366206400, .index = PLLVAL(165, 6, 1), }, /* FVco 732.412800 */ + { .frequency = 372556800, .index = PLLVAL(124, 4, 1), }, /* FVco 745.113600 */ + { .frequency = 378201600, .index = PLLVAL(126, 4, 1), }, /* FVco 756.403200 */ + { .frequency = 384652800, .index = PLLVAL(151, 5, 1), }, /* FVco 769.305600 */ + { .frequency = 391608000, .index = PLLVAL(177, 6, 1), }, /* FVco 783.216000 */ + { .frequency = 396264960, .index = PLLVAL(109, 3, 1), }, /* FVco 792.529920 */ + { .frequency = 402192000, .index = PLLVAL(87, 2, 1), }, /* FVco 804.384000 */ +}; + +static int s3c2440_plls169344_add(struct sys_device *dev) +{ + struct clk *xtal_clk; + unsigned long xtal; + + xtal_clk = clk_get(NULL, "xtal"); + if (IS_ERR(xtal_clk)) + return PTR_ERR(xtal_clk); + + xtal = clk_get_rate(xtal_clk); + clk_put(xtal_clk); + + if (xtal == 169344000) { + printk(KERN_INFO "Using PLL table for 16.9344MHz crystal\n"); + return s3c_plltab_register(s3c2440_plls_169344, + ARRAY_SIZE(s3c2440_plls_169344)); + } + + return 0; +} + +static struct sysdev_driver s3c2440_plls169344_drv = { + .add = s3c2440_plls169344_add, +}; + +static int __init s3c2440_pll_16934400(void) +{ + return sysdev_driver_register(&s3c2440_sysclass, + &s3c2440_plls169344_drv); + +} + +arch_initcall(s3c2440_pll_16934400); + +static struct sysdev_driver s3c2442_plls169344_drv = { + .add = s3c2440_plls169344_add, +}; + +static int __init s3c2442_pll_16934400(void) +{ + return sysdev_driver_register(&s3c2442_sysclass, + &s3c2442_plls169344_drv); + +} + +arch_initcall(s3c2442_pll_16934400); |