diff options
Diffstat (limited to 'drivers/leds')
| -rw-r--r-- | drivers/leds/Kconfig | 9 | ||||
| -rw-r--r-- | drivers/leds/Makefile | 1 | ||||
| -rw-r--r-- | drivers/leds/leds-ss4200.c | 552 |
3 files changed, 562 insertions, 0 deletions
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig index e4f599f20e3..e481d3c52a5 100644 --- a/drivers/leds/Kconfig +++ b/drivers/leds/Kconfig @@ -236,6 +236,15 @@ config LEDS_BD2802 This option enables support for BD2802GU RGB LED driver chips accessed via the I2C bus. +config LEDS_INTEL_SS4200 + tristate "LED driver for Intel NAS SS4200 series" + depends on LEDS_CLASS && PCI && DMI + help + This option enables support for the Intel SS4200 series of + Network Attached Storage servers. You may control the hard + drive or power LEDs on the front panel. Using this driver + can stop the front LED from blinking after startup. + comment "LED Triggers" config LEDS_TRIGGERS diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile index 46d72704d60..12b7a20fcfe 100644 --- a/drivers/leds/Makefile +++ b/drivers/leds/Makefile @@ -29,6 +29,7 @@ obj-$(CONFIG_LEDS_DA903X) += leds-da903x.o obj-$(CONFIG_LEDS_WM831X_STATUS) += leds-wm831x-status.o obj-$(CONFIG_LEDS_WM8350) += leds-wm8350.o obj-$(CONFIG_LEDS_PWM) += leds-pwm.o +obj-$(CONFIG_LEDS_INTEL_SS4200) += leds-ss4200.o # LED SPI Drivers obj-$(CONFIG_LEDS_DAC124S085) += leds-dac124s085.o diff --git a/drivers/leds/leds-ss4200.c b/drivers/leds/leds-ss4200.c new file mode 100644 index 00000000000..0ec4ec3bc82 --- /dev/null +++ b/drivers/leds/leds-ss4200.c @@ -0,0 +1,552 @@ +/* + * SS4200-E Hardware API + * Copyright (c) 2009, Intel Corporation. + * Copyright IBM Corporation, 2009 + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + * + * Author: Dave Hansen <dave@sr71.net> + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/dmi.h> +#include <linux/init.h> +#include <linux/ioport.h> +#include <linux/kernel.h> +#include <linux/leds.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/types.h> +#include <linux/uaccess.h> + +MODULE_AUTHOR("Rodney Girod <rgirod@confocus.com>, Dave Hansen <dave@sr71.net>"); +MODULE_DESCRIPTION("Intel NAS/Home Server ICH7 GPIO Driver"); +MODULE_LICENSE("GPL"); + +/* + * ICH7 LPC/GPIO PCI Config register offsets + */ +#define PMBASE 0x040 +#define GPIO_BASE 0x048 +#define GPIO_CTRL 0x04c +#define GPIO_EN 0x010 + +/* + * The ICH7 GPIO register block is 64 bytes in size. + */ +#define ICH7_GPIO_SIZE 64 + +/* + * Define register offsets within the ICH7 register block. + */ +#define GPIO_USE_SEL 0x000 +#define GP_IO_SEL 0x004 +#define GP_LVL 0x00c +#define GPO_BLINK 0x018 +#define GPI_INV 0x030 +#define GPIO_USE_SEL2 0x034 +#define GP_IO_SEL2 0x038 +#define GP_LVL2 0x03c + +/* + * PCI ID of the Intel ICH7 LPC Device within which the GPIO block lives. + */ +static struct pci_device_id ich7_lpc_pci_id[] = +{ + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_0) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_1) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH7_30) }, + { } /* NULL entry */ +}; + +MODULE_DEVICE_TABLE(pci, ich7_lpc_pci_id); + +static int __init ss4200_led_dmi_callback(const struct dmi_system_id *id) +{ + pr_info("detected '%s'\n", id->ident); + return 1; +} + +static unsigned int __initdata nodetect; +module_param_named(nodetect, nodetect, bool, 0); +MODULE_PARM_DESC(nodetect, "Skip DMI-based hardware detection"); + +/* + * struct nas_led_whitelist - List of known good models + * + * Contains the known good models this driver is compatible with. + * When adding a new model try to be as strict as possible. This + * makes it possible to keep the false positives (the model is + * detected as working, but in reality it is not) as low as + * possible. + */ +static struct dmi_system_id __initdata nas_led_whitelist[] = { + { + .callback = ss4200_led_dmi_callback, + .ident = "Intel SS4200-E", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Intel"), + DMI_MATCH(DMI_PRODUCT_NAME, "SS4200-E"), + DMI_MATCH(DMI_PRODUCT_VERSION, "1.00.00") + } + }, +}; + +/* + * Base I/O address assigned to the Power Management register block + */ +static u32 g_pm_io_base; + +/* + * Base I/O address assigned to the ICH7 GPIO register block + */ +static u32 nas_gpio_io_base; + +/* + * When we successfully register a region, we are returned a resource. + * We use these to identify which regions we need to release on our way + * back out. + */ +static struct resource *gp_gpio_resource; + +struct nasgpio_led { + char *name; + u32 gpio_bit; + struct led_classdev led_cdev; +}; + +/* + * gpio_bit(s) are the ICH7 GPIO bit assignments + */ +static struct nasgpio_led nasgpio_leds[] = { + { .name = "hdd1:blue:sata", .gpio_bit = 0 }, + { .name = "hdd1:amber:sata", .gpio_bit = 1 }, + { .name = "hdd2:blue:sata", .gpio_bit = 2 }, + { .name = "hdd2:amber:sata", .gpio_bit = 3 }, + { .name = "hdd3:blue:sata", .gpio_bit = 4 }, + { .name = "hdd3:amber:sata", .gpio_bit = 5 }, + { .name = "hdd4:blue:sata", .gpio_bit = 6 }, + { .name = "hdd4:amber:sata", .gpio_bit = 7 }, + { .name = "power:blue:power", .gpio_bit = 27}, + { .name = "power:amber:power", .gpio_bit = 28}, +}; + +#define NAS_RECOVERY 0x00000400 /* GPIO10 */ + +static struct nasgpio_led * +led_classdev_to_nasgpio_led(struct led_classdev *led_cdev) +{ + return container_of(led_cdev, struct nasgpio_led, led_cdev); +} + +static struct nasgpio_led *get_led_named(char *name) +{ + int i; + for (i = 0; i < ARRAY_SIZE(nasgpio_leds); i++) { + if (strcmp(nasgpio_leds[i].name, name)) + continue; + return &nasgpio_leds[i]; + } + return NULL; +} + +/* + * This protects access to the gpio ports. + */ +static DEFINE_SPINLOCK(nasgpio_gpio_lock); + +/* + * There are two gpio ports, one for blinking and the other + * for power. @port tells us if we're doing blinking or + * power control. + * + * Caller must hold nasgpio_gpio_lock + */ +static void __nasgpio_led_set_attr(struct led_classdev *led_cdev, + u32 port, u32 value) +{ + struct nasgpio_led *led = led_classdev_to_nasgpio_led(led_cdev); + u32 gpio_out; + + gpio_out = inl(nas_gpio_io_base + port); + if (value) + gpio_out |= (1<<led->gpio_bit); + else + gpio_out &= ~(1<<led->gpio_bit); + + outl(gpio_out, nas_gpio_io_base + port); +} + +static void nasgpio_led_set_attr(struct led_classdev *led_cdev, + u32 port, u32 value) +{ + spin_lock(&nasgpio_gpio_lock); + __nasgpio_led_set_attr(led_cdev, port, value); + spin_unlock(&nasgpio_gpio_lock); +} + +u32 nasgpio_led_get_attr(struct led_classdev *led_cdev, u32 port) +{ + struct nasgpio_led *led = led_classdev_to_nasgpio_led(led_cdev); + u32 gpio_in; + + spin_lock(&nasgpio_gpio_lock); + gpio_in = inl(nas_gpio_io_base + port); + spin_unlock(&nasgpio_gpio_lock); + if (gpio_in & (1<<led->gpio_bit)) + return 1; + return 0; +} + +/* + * There is actual brightness control in the hardware, + * but it is via smbus commands and not implemented + * in this driver. + */ +static void nasgpio_led_set_brightness(struct led_classdev *led_cdev, + enum led_brightness brightness) +{ + u32 setting = 0; + if (brightness >= LED_HALF) + setting = 1; + /* + * Hold the lock across both operations. This ensures + * consistency so that both the "turn off blinking" + * and "turn light off" operations complete as a set. + */ + spin_lock(&nasgpio_gpio_lock); + /* + * LED class documentation asks that past blink state + * be disabled when brightness is turned to zero. + */ + if (brightness == 0) + __nasgpio_led_set_attr(led_cdev, GPO_BLINK, 0); + __nasgpio_led_set_attr(led_cdev, GP_LVL, setting); + spin_unlock(&nasgpio_gpio_lock); +} + +static int nasgpio_led_set_blink(struct led_classdev *led_cdev, + unsigned long *delay_on, + unsigned long *delay_off) +{ + u32 setting = 1; + if (!(*delay_on == 0 && *delay_off == 0) && + !(*delay_on == 500 && *delay_off == 500)) + return -EINVAL; + /* + * These are very approximate. + */ + *delay_on = 500; + *delay_off = 500; + + nasgpio_led_set_attr(led_cdev, GPO_BLINK, setting); + + return 0; +} + + +/* + * Initialize the ICH7 GPIO registers for NAS usage. The BIOS should have + * already taken care of this, but we will do so in a non destructive manner + * so that we have what we need whether the BIOS did it or not. + */ +static int __devinit ich7_gpio_init(struct device *dev) +{ + int i; + u32 config_data = 0; + u32 all_nas_led = 0; + + for (i = 0; i < ARRAY_SIZE(nasgpio_leds); i++) + all_nas_led |= (1<<nasgpio_leds[i].gpio_bit); + + spin_lock(&nasgpio_gpio_lock); + /* + * We need to enable all of the GPIO lines used by the NAS box, + * so we will read the current Use Selection and add our usage + * to it. This should be benign with regard to the original + * BIOS configuration. + */ + config_data = inl(nas_gpio_io_base + GPIO_USE_SEL); + dev_dbg(dev, ": Data read from GPIO_USE_SEL = 0x%08x\n", config_data); + config_data |= all_nas_led + NAS_RECOVERY; + outl(config_data, nas_gpio_io_base + GPIO_USE_SEL); + config_data = inl(nas_gpio_io_base + GPIO_USE_SEL); + dev_dbg(dev, ": GPIO_USE_SEL = 0x%08x\n\n", config_data); + + /* + * The LED GPIO outputs need to be configured for output, so we + * will ensure that all LED lines are cleared for output and the + * RECOVERY line ready for input. This too should be benign with + * regard to BIOS configuration. + */ + config_data = inl(nas_gpio_io_base + GP_IO_SEL); + dev_dbg(dev, ": Data read from GP_IO_SEL = 0x%08x\n", + config_data); + config_data &= ~all_nas_led; + config_data |= NAS_RECOVERY; + outl(config_data, nas_gpio_io_base + GP_IO_SEL); + config_data = inl(nas_gpio_io_base + GP_IO_SEL); + dev_dbg(dev, ": GP_IO_SEL = 0x%08x\n", config_data); + + /* + * In our final system, the BIOS will initialize the state of all + * of the LEDs. For now, we turn them all off (or Low). + */ + config_data = inl(nas_gpio_io_base + GP_LVL); + dev_dbg(dev, ": Data read from GP_LVL = 0x%08x\n", config_data); + /* + * In our final system, the BIOS will initialize the blink state of all + * of the LEDs. For now, we turn blink off for all of them. + */ + config_data = inl(nas_gpio_io_base + GPO_BLINK); + dev_dbg(dev, ": Data read from GPO_BLINK = 0x%08x\n", config_data); + + /* + * At this moment, I am unsure if anything needs to happen with GPI_INV + */ + config_data = inl(nas_gpio_io_base + GPI_INV); + dev_dbg(dev, ": Data read from GPI_INV = 0x%08x\n", config_data); + + spin_unlock(&nasgpio_gpio_lock); + return 0; +} + +static void ich7_lpc_cleanup(struct device *dev) +{ + /* + * If we were given exclusive use of the GPIO + * I/O Address range, we must return it. + */ + if (gp_gpio_resource) { + dev_dbg(dev, ": Releasing GPIO I/O addresses\n"); + release_region(nas_gpio_io_base, ICH7_GPIO_SIZE); + gp_gpio_resource = NULL; + } +} + +/* + * The OS has determined that the LPC of the Intel ICH7 Southbridge is present + * so we can retrive the required operational information and prepare the GPIO. + */ +static struct pci_dev *nas_gpio_pci_dev; +static int __devinit ich7_lpc_probe(struct pci_dev *dev, + const struct pci_device_id *id) +{ + int status = 0; + u32 gc = 0; + + pci_enable_device(dev); + + nas_gpio_pci_dev = dev; + status = pci_read_config_dword(dev, PMBASE, &g_pm_io_base); + if (status) + goto out; + g_pm_io_base &= 0x00000ff80; + + status = pci_read_config_dword(dev, GPIO_CTRL, &gc); + if (!(GPIO_EN & gc)) { + status = -EEXIST; + dev_info(&dev->dev, + "ERROR: The LPC GPIO Block has not been enabled.\n"); + goto out; + } + + status = pci_read_config_dword(dev, GPIO_BASE, &nas_gpio_io_base); + if (0 > status) { + dev_info(&dev->dev, "Unable to read GPIOBASE.\n"); + goto out; + } + dev_dbg(&dev->dev, ": GPIOBASE = 0x%08x\n", nas_gpio_io_base); + nas_gpio_io_base &= 0x00000ffc0; + + /* + * Insure that we have exclusive access to the GPIO I/O address range. + */ + gp_gpio_resource = request_region(nas_gpio_io_base, ICH7_GPIO_SIZE, + KBUILD_MODNAME); + if (NULL == gp_gpio_resource) { + dev_info(&dev->dev, + "ERROR Unable to register GPIO I/O addresses.\n"); + status = -1; + goto out; + } + + /* + * Initialize the GPIO for NAS/Home Server Use + */ + ich7_gpio_init(&dev->dev); + +out: + if (status) { + ich7_lpc_cleanup(&dev->dev); + pci_disable_device(dev); + } + return status; +} + +static void ich7_lpc_remove(struct pci_dev *dev) +{ + ich7_lpc_cleanup(&dev->dev); + pci_disable_device(dev); +} + +/* + * pci_driver structure passed to the PCI modules + */ +static struct pci_driver nas_gpio_pci_driver = { + .name = KBUILD_MODNAME, + .id_table = ich7_lpc_pci_id, + .probe = ich7_lpc_probe, + .remove = ich7_lpc_remove, +}; + +static struct led_classdev *get_classdev_for_led_nr(int nr) +{ + struct nasgpio_led *nas_led = &nasgpio_leds[nr]; + struct led_classdev *led = &nas_led->led_cdev; + return led; +} + + +static void set_power_light_amber_noblink(void) +{ + struct nasgpio_led *amber = get_led_named("power:amber:power"); + struct nasgpio_led *blue = get_led_named("power:blue:power"); + + if (!amber || !blue) + return; + /* + * LED_OFF implies disabling future blinking + */ + pr_debug("setting blue off and amber on\n"); + + nasgpio_led_set_brightness(&blue->led_cdev, LED_OFF); + nasgpio_led_set_brightness(&amber->led_cdev, LED_FULL); +} + +static ssize_t nas_led_blink_show(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct led_classdev *led = dev_get_drvdata(dev); + int blinking = 0; + if (nasgpio_led_get_attr(led, GPO_BLINK)) + blinking = 1; + return sprintf(buf, "%u\n", blinking); +} + +static ssize_t nas_led_blink_store(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t size) +{ + int ret; + struct led_classdev *led = dev_get_drvdata(dev); + unsigned long blink_state; + + ret = strict_strtoul(buf, 10, &blink_state); + if (ret) + return ret; + + nasgpio_led_set_attr(led, GPO_BLINK, blink_state); + + return size; +} + +static DEVICE_ATTR(blink, 0644, nas_led_blink_show, nas_led_blink_store); + +static int register_nasgpio_led(int led_nr) +{ + int ret; + struct nasgpio_led *nas_led = &nasgpio_leds[led_nr]; + struct led_classdev *led = get_classdev_for_led_nr(led_nr); + + led->name = nas_led->name; + led->brightness = LED_OFF; + if (nasgpio_led_get_attr(led, GP_LVL)) + led->brightness = LED_FULL; + led->brightness_set = nasgpio_led_set_brightness; + led->blink_set = nasgpio_led_set_blink; + ret = led_classdev_register(&nas_gpio_pci_dev->dev, led); + if (ret) + return ret; + ret = device_create_file(led->dev, &dev_attr_blink); + if (ret) + led_classdev_unregister(led); + return ret; +} + +static void unregister_nasgpio_led(int led_nr) +{ + struct led_classdev *led = get_classdev_for_led_nr(led_nr); + led_classdev_unregister(led); + device_remove_file(led->dev, &dev_attr_blink); +} +/* + * module load/initialization + */ +static int __init nas_gpio_init(void) +{ + int i; + int ret = 0; + int nr_devices = 0; + + nr_devices = dmi_check_system(nas_led_whitelist); + if (nodetect) { + pr_info("skipping hardware autodetection\n"); + pr_info("Please send 'dmidecode' output to dave@sr71.net\n"); + nr_devices++; + } + + if (nr_devices <= 0) { + pr_info("no LED devices found\n"); + return -ENODEV; + } + + pr_info("registering PCI driver\n"); + ret = pci_register_driver(&nas_gpio_pci_driver); + if (ret) + return ret; + for (i = 0; i < ARRAY_SIZE(nasgpio_leds); i++) { + ret = register_nasgpio_led(i); + if (ret) + goto out_err; + } + /* + * When the system powers on, the BIOS leaves the power + * light blue and blinking. This will turn it solid + * amber once the driver is loaded. + */ + set_power_light_amber_noblink(); + return 0; +out_err: + for (; i >= 0; i--) + unregister_nasgpio_led(i); + pci_unregister_driver(&nas_gpio_pci_driver); + return ret; +} + +/* + * module unload + */ +static void __exit nas_gpio_exit(void) +{ + int i; + pr_info("Unregistering driver\n"); + for (i = 0; i < ARRAY_SIZE(nasgpio_leds); i++) + unregister_nasgpio_led(i); + pci_unregister_driver(&nas_gpio_pci_driver); +} + +module_init(nas_gpio_init); +module_exit(nas_gpio_exit); |