diff options
Diffstat (limited to 'drivers/memstick/host/r592.h')
| -rw-r--r-- | drivers/memstick/host/r592.h | 175 |
1 files changed, 175 insertions, 0 deletions
diff --git a/drivers/memstick/host/r592.h b/drivers/memstick/host/r592.h new file mode 100644 index 00000000000..c5726c1e883 --- /dev/null +++ b/drivers/memstick/host/r592.h @@ -0,0 +1,175 @@ +/* + * Copyright (C) 2010 - Maxim Levitsky + * driver for Ricoh memstick readers + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef R592_H + +#include <linux/memstick.h> +#include <linux/spinlock.h> +#include <linux/interrupt.h> +#include <linux/workqueue.h> +#include <linux/kfifo.h> +#include <linux/ctype.h> + +/* write to this reg (number,len) triggers TPC execution */ +#define R592_TPC_EXEC 0x00 +#define R592_TPC_EXEC_LEN_SHIFT 16 /* Bits 16..25 are TPC len */ +#define R592_TPC_EXEC_BIG_FIFO (1 << 26) /* If bit 26 is set, large fifo is used (reg 48) */ +#define R592_TPC_EXEC_TPC_SHIFT 28 /* Bits 28..31 are the TPC number */ + + +/* Window for small TPC fifo (big endian)*/ +/* reads and writes always are done in 8 byte chunks */ +/* Not used in driver, because large fifo does better job */ +#define R592_SFIFO 0x08 + + +/* Status register (ms int, small fifo, IO)*/ +#define R592_STATUS 0x10 + /* Parallel INT bits */ +#define R592_STATUS_P_CMDNACK (1 << 16) /* INT reg: NACK (parallel mode) */ +#define R592_STATUS_P_BREQ (1 << 17) /* INT reg: card ready (parallel mode)*/ +#define R592_STATUS_P_INTERR (1 << 18) /* INT reg: int error (parallel mode)*/ +#define R592_STATUS_P_CED (1 << 19) /* INT reg: command done (parallel mode) */ + + /* Fifo status */ +#define R592_STATUS_SFIFO_FULL (1 << 20) /* Small Fifo almost full (last chunk is written) */ +#define R592_STATUS_SFIFO_EMPTY (1 << 21) /* Small Fifo empty */ + + /* Error detection via CRC */ +#define R592_STATUS_SEND_ERR (1 << 24) /* Send failed */ +#define R592_STATUS_RECV_ERR (1 << 25) /* Receive failed */ + + /* Card state */ +#define R592_STATUS_RDY (1 << 28) /* RDY signal received */ +#define R592_STATUS_CED (1 << 29) /* INT: Command done (serial mode)*/ +#define R592_STATUS_SFIFO_INPUT (1 << 30) /* Small fifo received data*/ + +#define R592_SFIFO_SIZE 32 /* total size of small fifo is 32 bytes */ +#define R592_SFIFO_PACKET 8 /* packet size of small fifo */ + +/* IO control */ +#define R592_IO 0x18 +#define R592_IO_16 (1 << 16) /* Set by default, can be cleared */ +#define R592_IO_18 (1 << 18) /* Set by default, can be cleared */ +#define R592_IO_SERIAL1 (1 << 20) /* Set by default, can be cleared, (cleared on parallel) */ +#define R592_IO_22 (1 << 22) /* Set by default, can be cleared */ +#define R592_IO_DIRECTION (1 << 24) /* TPC direction (1 write 0 read) */ +#define R592_IO_26 (1 << 26) /* Set by default, can be cleared */ +#define R592_IO_SERIAL2 (1 << 30) /* Set by default, can be cleared (cleared on parallel), serial doesn't work if unset */ +#define R592_IO_RESET (1 << 31) /* Reset, sets defaults*/ + + +/* Turns hardware on/off */ +#define R592_POWER 0x20 /* bits 0-7 writeable */ +#define R592_POWER_0 (1 << 0) /* set on start, cleared on stop - must be set*/ +#define R592_POWER_1 (1 << 1) /* set on start, cleared on stop - must be set*/ +#define R592_POWER_3 (1 << 3) /* must be clear */ +#define R592_POWER_20 (1 << 5) /* set before switch to parallel */ + +/* IO mode*/ +#define R592_IO_MODE 0x24 +#define R592_IO_MODE_SERIAL 1 +#define R592_IO_MODE_PARALLEL 3 + + +/* IRQ,card detection,large fifo (first word irq status, second enable) */ +/* IRQs are ACKed by clearing the bits */ +#define R592_REG_MSC 0x28 +#define R592_REG_MSC_PRSNT (1 << 1) /* card present (only status)*/ +#define R592_REG_MSC_IRQ_INSERT (1 << 8) /* detect insert / card insered */ +#define R592_REG_MSC_IRQ_REMOVE (1 << 9) /* detect removal / card removed */ +#define R592_REG_MSC_FIFO_EMPTY (1 << 10) /* fifo is empty */ +#define R592_REG_MSC_FIFO_DMA_DONE (1 << 11) /* dma enable / dma done */ + +#define R592_REG_MSC_FIFO_USER_ORN (1 << 12) /* set if software reads empty fifo (if R592_REG_MSC_FIFO_EMPTY is set) */ +#define R592_REG_MSC_FIFO_MISMATH (1 << 13) /* set if amount of data in fifo doesn't match amount in TPC */ +#define R592_REG_MSC_FIFO_DMA_ERR (1 << 14) /* IO failure */ +#define R592_REG_MSC_LED (1 << 15) /* clear to turn led off (only status)*/ + +#define DMA_IRQ_ACK_MASK \ + (R592_REG_MSC_FIFO_DMA_DONE | R592_REG_MSC_FIFO_DMA_ERR) + +#define DMA_IRQ_EN_MASK (DMA_IRQ_ACK_MASK << 16) + +#define IRQ_ALL_ACK_MASK 0x00007F00 +#define IRQ_ALL_EN_MASK (IRQ_ALL_ACK_MASK << 16) + +/* DMA address for large FIFO read/writes*/ +#define R592_FIFO_DMA 0x2C + +/* PIO access to large FIFO (512 bytes) (big endian)*/ +#define R592_FIFO_PIO 0x30 +#define R592_LFIFO_SIZE 512 /* large fifo size */ + + +/* large FIFO DMA settings */ +#define R592_FIFO_DMA_SETTINGS 0x34 +#define R592_FIFO_DMA_SETTINGS_EN (1 << 0) /* DMA enabled */ +#define R592_FIFO_DMA_SETTINGS_DIR (1 << 1) /* Dma direction (1 read, 0 write) */ +#define R592_FIFO_DMA_SETTINGS_CAP (1 << 24) /* Dma is aviable */ + +/* Maybe just an delay */ +/* Bits 17..19 are just number */ +/* bit 16 is set, then bit 20 is waited */ +/* time to wait is about 50 spins * 2 ^ (bits 17..19) */ +/* seems to be possible just to ignore */ +/* Probably debug register */ +#define R592_REG38 0x38 +#define R592_REG38_CHANGE (1 << 16) /* Start bit */ +#define R592_REG38_DONE (1 << 20) /* HW set this after the delay */ +#define R592_REG38_SHIFT 17 + +/* Debug register, written (0xABCDEF00) when error happens - not used*/ +#define R592_REG_3C 0x3C + +struct r592_device { + struct pci_dev *pci_dev; + struct memstick_host *host; /* host backpointer */ + struct memstick_request *req; /* current request */ + + /* Registers, IRQ */ + void __iomem *mmio; + int irq; + spinlock_t irq_lock; + spinlock_t io_thread_lock; + struct timer_list detect_timer; + + struct task_struct *io_thread; + bool parallel_mode; + + DECLARE_KFIFO(pio_fifo, u8, sizeof(u32)); + + /* DMA area */ + int dma_capable; + int dma_error; + struct completion dma_done; + void *dummy_dma_page; + dma_addr_t dummy_dma_page_physical_address; + +}; + +#define DRV_NAME "r592" + + +#define message(format, ...) \ + printk(KERN_INFO DRV_NAME ": " format "\n", ## __VA_ARGS__) + +#define __dbg(level, format, ...) \ + do { \ + if (debug >= level) \ + printk(KERN_DEBUG DRV_NAME \ + ": " format "\n", ## __VA_ARGS__); \ + } while (0) + + +#define dbg(format, ...) __dbg(1, format, ## __VA_ARGS__) +#define dbg_verbose(format, ...) __dbg(2, format, ## __VA_ARGS__) +#define dbg_reg(format, ...) __dbg(3, format, ## __VA_ARGS__) + +#endif |