diff options
Diffstat (limited to 'drivers/misc/c2port/core.c')
| -rw-r--r-- | drivers/misc/c2port/core.c | 1003 |
1 files changed, 1003 insertions, 0 deletions
diff --git a/drivers/misc/c2port/core.c b/drivers/misc/c2port/core.c new file mode 100644 index 00000000000..0207dd59090 --- /dev/null +++ b/drivers/misc/c2port/core.c @@ -0,0 +1,1003 @@ +/* + * Silicon Labs C2 port core Linux support + * + * Copyright (c) 2007 Rodolfo Giometti <giometti@linux.it> + * Copyright (c) 2007 Eurotech S.p.A. <info@eurotech.it> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/errno.h> +#include <linux/err.h> +#include <linux/kernel.h> +#include <linux/ctype.h> +#include <linux/delay.h> +#include <linux/idr.h> +#include <linux/sched.h> + +#include <linux/c2port.h> + +#define DRIVER_NAME "c2port" +#define DRIVER_VERSION "0.51.0" + +static DEFINE_SPINLOCK(c2port_idr_lock); +static DEFINE_IDR(c2port_idr); + +/* + * Local variables + */ + +static struct class *c2port_class; + +/* + * C2 registers & commands defines + */ + +/* C2 registers */ +#define C2PORT_DEVICEID 0x00 +#define C2PORT_REVID 0x01 +#define C2PORT_FPCTL 0x02 +#define C2PORT_FPDAT 0xB4 + +/* C2 interface commands */ +#define C2PORT_GET_VERSION 0x01 +#define C2PORT_DEVICE_ERASE 0x03 +#define C2PORT_BLOCK_READ 0x06 +#define C2PORT_BLOCK_WRITE 0x07 +#define C2PORT_PAGE_ERASE 0x08 + +/* C2 status return codes */ +#define C2PORT_INVALID_COMMAND 0x00 +#define C2PORT_COMMAND_FAILED 0x02 +#define C2PORT_COMMAND_OK 0x0d + +/* + * C2 port low level signal managements + */ + +static void c2port_reset(struct c2port_device *dev) +{ + struct c2port_ops *ops = dev->ops; + + /* To reset the device we have to keep clock line low for at least + * 20us. + */ + local_irq_disable(); + ops->c2ck_set(dev, 0); + udelay(25); + ops->c2ck_set(dev, 1); + local_irq_enable(); + + udelay(1); +} + +static void c2port_strobe_ck(struct c2port_device *dev) +{ + struct c2port_ops *ops = dev->ops; + + /* During hi-low-hi transition we disable local IRQs to avoid + * interructions since C2 port specification says that it must be + * shorter than 5us, otherwise the microcontroller may consider + * it as a reset signal! + */ + local_irq_disable(); + ops->c2ck_set(dev, 0); + udelay(1); + ops->c2ck_set(dev, 1); + local_irq_enable(); + + udelay(1); +} + +/* + * C2 port basic functions + */ + +static void c2port_write_ar(struct c2port_device *dev, u8 addr) +{ + struct c2port_ops *ops = dev->ops; + int i; + + /* START field */ + c2port_strobe_ck(dev); + + /* INS field (11b, LSB first) */ + ops->c2d_dir(dev, 0); + ops->c2d_set(dev, 1); + c2port_strobe_ck(dev); + ops->c2d_set(dev, 1); + c2port_strobe_ck(dev); + + /* ADDRESS field */ + for (i = 0; i < 8; i++) { + ops->c2d_set(dev, addr & 0x01); + c2port_strobe_ck(dev); + + addr >>= 1; + } + + /* STOP field */ + ops->c2d_dir(dev, 1); + c2port_strobe_ck(dev); +} + +static int c2port_read_ar(struct c2port_device *dev, u8 *addr) +{ + struct c2port_ops *ops = dev->ops; + int i; + + /* START field */ + c2port_strobe_ck(dev); + + /* INS field (10b, LSB first) */ + ops->c2d_dir(dev, 0); + ops->c2d_set(dev, 0); + c2port_strobe_ck(dev); + ops->c2d_set(dev, 1); + c2port_strobe_ck(dev); + + /* ADDRESS field */ + ops->c2d_dir(dev, 1); + *addr = 0; + for (i = 0; i < 8; i++) { + *addr >>= 1; /* shift in 8-bit ADDRESS field LSB first */ + + c2port_strobe_ck(dev); + if (ops->c2d_get(dev)) + *addr |= 0x80; + } + + /* STOP field */ + c2port_strobe_ck(dev); + + return 0; +} + +static int c2port_write_dr(struct c2port_device *dev, u8 data) +{ + struct c2port_ops *ops = dev->ops; + int timeout, i; + + /* START field */ + c2port_strobe_ck(dev); + + /* INS field (01b, LSB first) */ + ops->c2d_dir(dev, 0); + ops->c2d_set(dev, 1); + c2port_strobe_ck(dev); + ops->c2d_set(dev, 0); + c2port_strobe_ck(dev); + + /* LENGTH field (00b, LSB first -> 1 byte) */ + ops->c2d_set(dev, 0); + c2port_strobe_ck(dev); + ops->c2d_set(dev, 0); + c2port_strobe_ck(dev); + + /* DATA field */ + for (i = 0; i < 8; i++) { + ops->c2d_set(dev, data & 0x01); + c2port_strobe_ck(dev); + + data >>= 1; + } + + /* WAIT field */ + ops->c2d_dir(dev, 1); + timeout = 20; + do { + c2port_strobe_ck(dev); + if (ops->c2d_get(dev)) + break; + + udelay(1); + } while (--timeout > 0); + if (timeout == 0) + return -EIO; + + /* STOP field */ + c2port_strobe_ck(dev); + + return 0; +} + +static int c2port_read_dr(struct c2port_device *dev, u8 *data) +{ + struct c2port_ops *ops = dev->ops; + int timeout, i; + + /* START field */ + c2port_strobe_ck(dev); + + /* INS field (00b, LSB first) */ + ops->c2d_dir(dev, 0); + ops->c2d_set(dev, 0); + c2port_strobe_ck(dev); + ops->c2d_set(dev, 0); + c2port_strobe_ck(dev); + + /* LENGTH field (00b, LSB first -> 1 byte) */ + ops->c2d_set(dev, 0); + c2port_strobe_ck(dev); + ops->c2d_set(dev, 0); + c2port_strobe_ck(dev); + + /* WAIT field */ + ops->c2d_dir(dev, 1); + timeout = 20; + do { + c2port_strobe_ck(dev); + if (ops->c2d_get(dev)) + break; + + udelay(1); + } while (--timeout > 0); + if (timeout == 0) + return -EIO; + + /* DATA field */ + *data = 0; + for (i = 0; i < 8; i++) { + *data >>= 1; /* shift in 8-bit DATA field LSB first */ + + c2port_strobe_ck(dev); + if (ops->c2d_get(dev)) + *data |= 0x80; + } + + /* STOP field */ + c2port_strobe_ck(dev); + + return 0; +} + +static int c2port_poll_in_busy(struct c2port_device *dev) +{ + u8 addr; + int ret, timeout = 20; + + do { + ret = (c2port_read_ar(dev, &addr)); + if (ret < 0) + return -EIO; + + if (!(addr & 0x02)) + break; + + udelay(1); + } while (--timeout > 0); + if (timeout == 0) + return -EIO; + + return 0; +} + +static int c2port_poll_out_ready(struct c2port_device *dev) +{ + u8 addr; + int ret, timeout = 10000; /* erase flash needs long time... */ + + do { + ret = (c2port_read_ar(dev, &addr)); + if (ret < 0) + return -EIO; + + if (addr & 0x01) + break; + + udelay(1); + } while (--timeout > 0); + if (timeout == 0) + return -EIO; + + return 0; +} + +/* + * sysfs methods + */ + +static ssize_t c2port_show_name(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + + return sprintf(buf, "%s\n", c2dev->name); +} + +static ssize_t c2port_show_flash_blocks_num(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + struct c2port_ops *ops = c2dev->ops; + + return sprintf(buf, "%d\n", ops->blocks_num); +} + +static ssize_t c2port_show_flash_block_size(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + struct c2port_ops *ops = c2dev->ops; + + return sprintf(buf, "%d\n", ops->block_size); +} + +static ssize_t c2port_show_flash_size(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + struct c2port_ops *ops = c2dev->ops; + + return sprintf(buf, "%d\n", ops->blocks_num * ops->block_size); +} + +static ssize_t c2port_show_access(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + + return sprintf(buf, "%d\n", c2dev->access); +} + +static ssize_t c2port_store_access(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + struct c2port_ops *ops = c2dev->ops; + int status, ret; + + ret = sscanf(buf, "%d", &status); + if (ret != 1) + return -EINVAL; + + mutex_lock(&c2dev->mutex); + + c2dev->access = !!status; + + /* If access is "on" clock should be HIGH _before_ setting the line + * as output and data line should be set as INPUT anyway */ + if (c2dev->access) + ops->c2ck_set(c2dev, 1); + ops->access(c2dev, c2dev->access); + if (c2dev->access) + ops->c2d_dir(c2dev, 1); + + mutex_unlock(&c2dev->mutex); + + return count; +} + +static ssize_t c2port_store_reset(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + + /* Check the device access status */ + if (!c2dev->access) + return -EBUSY; + + mutex_lock(&c2dev->mutex); + + c2port_reset(c2dev); + c2dev->flash_access = 0; + + mutex_unlock(&c2dev->mutex); + + return count; +} + +static ssize_t __c2port_show_dev_id(struct c2port_device *dev, char *buf) +{ + u8 data; + int ret; + + /* Select DEVICEID register for C2 data register accesses */ + c2port_write_ar(dev, C2PORT_DEVICEID); + + /* Read and return the device ID register */ + ret = c2port_read_dr(dev, &data); + if (ret < 0) + return ret; + + return sprintf(buf, "%d\n", data); +} + +static ssize_t c2port_show_dev_id(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + ssize_t ret; + + /* Check the device access status */ + if (!c2dev->access) + return -EBUSY; + + mutex_lock(&c2dev->mutex); + ret = __c2port_show_dev_id(c2dev, buf); + mutex_unlock(&c2dev->mutex); + + if (ret < 0) + dev_err(dev, "cannot read from %s\n", c2dev->name); + + return ret; +} + +static ssize_t __c2port_show_rev_id(struct c2port_device *dev, char *buf) +{ + u8 data; + int ret; + + /* Select REVID register for C2 data register accesses */ + c2port_write_ar(dev, C2PORT_REVID); + + /* Read and return the revision ID register */ + ret = c2port_read_dr(dev, &data); + if (ret < 0) + return ret; + + return sprintf(buf, "%d\n", data); +} + +static ssize_t c2port_show_rev_id(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + ssize_t ret; + + /* Check the device access status */ + if (!c2dev->access) + return -EBUSY; + + mutex_lock(&c2dev->mutex); + ret = __c2port_show_rev_id(c2dev, buf); + mutex_unlock(&c2dev->mutex); + + if (ret < 0) + dev_err(c2dev->dev, "cannot read from %s\n", c2dev->name); + + return ret; +} + +static ssize_t c2port_show_flash_access(struct device *dev, + struct device_attribute *attr, char *buf) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + + return sprintf(buf, "%d\n", c2dev->flash_access); +} + +static ssize_t __c2port_store_flash_access(struct c2port_device *dev, + int status) +{ + int ret; + + /* Check the device access status */ + if (!dev->access) + return -EBUSY; + + dev->flash_access = !!status; + + /* If flash_access is off we have nothing to do... */ + if (dev->flash_access == 0) + return 0; + + /* Target the C2 flash programming control register for C2 data + * register access */ + c2port_write_ar(dev, C2PORT_FPCTL); + + /* Write the first keycode to enable C2 Flash programming */ + ret = c2port_write_dr(dev, 0x02); + if (ret < 0) + return ret; + + /* Write the second keycode to enable C2 Flash programming */ + ret = c2port_write_dr(dev, 0x01); + if (ret < 0) + return ret; + + /* Delay for at least 20ms to ensure the target is ready for + * C2 flash programming */ + mdelay(25); + + return 0; +} + +static ssize_t c2port_store_flash_access(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + int status; + ssize_t ret; + + ret = sscanf(buf, "%d", &status); + if (ret != 1) + return -EINVAL; + + mutex_lock(&c2dev->mutex); + ret = __c2port_store_flash_access(c2dev, status); + mutex_unlock(&c2dev->mutex); + + if (ret < 0) { + dev_err(c2dev->dev, "cannot enable %s flash programming\n", + c2dev->name); + return ret; + } + + return count; +} + +static ssize_t __c2port_write_flash_erase(struct c2port_device *dev) +{ + u8 status; + int ret; + + /* Target the C2 flash programming data register for C2 data register + * access. + */ + c2port_write_ar(dev, C2PORT_FPDAT); + + /* Send device erase command */ + c2port_write_dr(dev, C2PORT_DEVICE_ERASE); + + /* Wait for input acknowledge */ + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + /* Should check status before starting FLASH access sequence */ + + /* Wait for status information */ + ret = c2port_poll_out_ready(dev); + if (ret < 0) + return ret; + + /* Read flash programming interface status */ + ret = c2port_read_dr(dev, &status); + if (ret < 0) + return ret; + if (status != C2PORT_COMMAND_OK) + return -EBUSY; + + /* Send a three-byte arming sequence to enable the device erase. + * If the sequence is not received correctly, the command will be + * ignored. + * Sequence is: 0xde, 0xad, 0xa5. + */ + c2port_write_dr(dev, 0xde); + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + c2port_write_dr(dev, 0xad); + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + c2port_write_dr(dev, 0xa5); + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + ret = c2port_poll_out_ready(dev); + if (ret < 0) + return ret; + + return 0; +} + +static ssize_t c2port_store_flash_erase(struct device *dev, + struct device_attribute *attr, + const char *buf, size_t count) +{ + struct c2port_device *c2dev = dev_get_drvdata(dev); + int ret; + + /* Check the device and flash access status */ + if (!c2dev->access || !c2dev->flash_access) + return -EBUSY; + + mutex_lock(&c2dev->mutex); + ret = __c2port_write_flash_erase(c2dev); + mutex_unlock(&c2dev->mutex); + + if (ret < 0) { + dev_err(c2dev->dev, "cannot erase %s flash\n", c2dev->name); + return ret; + } + + return count; +} + +static ssize_t __c2port_read_flash_data(struct c2port_device *dev, + char *buffer, loff_t offset, size_t count) +{ + struct c2port_ops *ops = dev->ops; + u8 status, nread = 128; + int i, ret; + + /* Check for flash end */ + if (offset >= ops->block_size * ops->blocks_num) + return 0; + + if (ops->block_size * ops->blocks_num - offset < nread) + nread = ops->block_size * ops->blocks_num - offset; + if (count < nread) + nread = count; + if (nread == 0) + return nread; + + /* Target the C2 flash programming data register for C2 data register + * access */ + c2port_write_ar(dev, C2PORT_FPDAT); + + /* Send flash block read command */ + c2port_write_dr(dev, C2PORT_BLOCK_READ); + + /* Wait for input acknowledge */ + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + /* Should check status before starting FLASH access sequence */ + + /* Wait for status information */ + ret = c2port_poll_out_ready(dev); + if (ret < 0) + return ret; + + /* Read flash programming interface status */ + ret = c2port_read_dr(dev, &status); + if (ret < 0) + return ret; + if (status != C2PORT_COMMAND_OK) + return -EBUSY; + + /* Send address high byte */ + c2port_write_dr(dev, offset >> 8); + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + /* Send address low byte */ + c2port_write_dr(dev, offset & 0x00ff); + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + /* Send address block size */ + c2port_write_dr(dev, nread); + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + /* Should check status before reading FLASH block */ + + /* Wait for status information */ + ret = c2port_poll_out_ready(dev); + if (ret < 0) + return ret; + + /* Read flash programming interface status */ + ret = c2port_read_dr(dev, &status); + if (ret < 0) + return ret; + if (status != C2PORT_COMMAND_OK) + return -EBUSY; + + /* Read flash block */ + for (i = 0; i < nread; i++) { + ret = c2port_poll_out_ready(dev); + if (ret < 0) + return ret; + + ret = c2port_read_dr(dev, buffer+i); + if (ret < 0) + return ret; + } + + return nread; +} + +static ssize_t c2port_read_flash_data(struct kobject *kobj, + struct bin_attribute *attr, + char *buffer, loff_t offset, size_t count) +{ + struct c2port_device *c2dev = + dev_get_drvdata(container_of(kobj, + struct device, kobj)); + ssize_t ret; + + /* Check the device and flash access status */ + if (!c2dev->access || !c2dev->flash_access) + return -EBUSY; + + mutex_lock(&c2dev->mutex); + ret = __c2port_read_flash_data(c2dev, buffer, offset, count); + mutex_unlock(&c2dev->mutex); + + if (ret < 0) + dev_err(c2dev->dev, "cannot read %s flash\n", c2dev->name); + + return ret; +} + +static ssize_t __c2port_write_flash_data(struct c2port_device *dev, + char *buffer, loff_t offset, size_t count) +{ + struct c2port_ops *ops = dev->ops; + u8 status, nwrite = 128; + int i, ret; + + if (nwrite > count) + nwrite = count; + if (ops->block_size * ops->blocks_num - offset < nwrite) + nwrite = ops->block_size * ops->blocks_num - offset; + + /* Check for flash end */ + if (offset >= ops->block_size * ops->blocks_num) + return -EINVAL; + + /* Target the C2 flash programming data register for C2 data register + * access */ + c2port_write_ar(dev, C2PORT_FPDAT); + + /* Send flash block write command */ + c2port_write_dr(dev, C2PORT_BLOCK_WRITE); + + /* Wait for input acknowledge */ + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + /* Should check status before starting FLASH access sequence */ + + /* Wait for status information */ + ret = c2port_poll_out_ready(dev); + if (ret < 0) + return ret; + + /* Read flash programming interface status */ + ret = c2port_read_dr(dev, &status); + if (ret < 0) + return ret; + if (status != C2PORT_COMMAND_OK) + return -EBUSY; + + /* Send address high byte */ + c2port_write_dr(dev, offset >> 8); + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + /* Send address low byte */ + c2port_write_dr(dev, offset & 0x00ff); + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + /* Send address block size */ + c2port_write_dr(dev, nwrite); + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + /* Should check status before writing FLASH block */ + + /* Wait for status information */ + ret = c2port_poll_out_ready(dev); + if (ret < 0) + return ret; + + /* Read flash programming interface status */ + ret = c2port_read_dr(dev, &status); + if (ret < 0) + return ret; + if (status != C2PORT_COMMAND_OK) + return -EBUSY; + + /* Write flash block */ + for (i = 0; i < nwrite; i++) { + ret = c2port_write_dr(dev, *(buffer+i)); + if (ret < 0) + return ret; + + ret = c2port_poll_in_busy(dev); + if (ret < 0) + return ret; + + } + + /* Wait for last flash write to complete */ + ret = c2port_poll_out_ready(dev); + if (ret < 0) + return ret; + + return nwrite; +} + +static ssize_t c2port_write_flash_data(struct kobject *kobj, + struct bin_attribute *attr, + char *buffer, loff_t offset, size_t count) +{ + struct c2port_device *c2dev = + dev_get_drvdata(container_of(kobj, + struct device, kobj)); + int ret; + + /* Check the device access status */ + if (!c2dev->access || !c2dev->flash_access) + return -EBUSY; + + mutex_lock(&c2dev->mutex); + ret = __c2port_write_flash_data(c2dev, buffer, offset, count); + mutex_unlock(&c2dev->mutex); + + if (ret < 0) + dev_err(c2dev->dev, "cannot write %s flash\n", c2dev->name); + + return ret; +} + +/* + * Class attributes + */ + +static struct device_attribute c2port_attrs[] = { + __ATTR(name, 0444, c2port_show_name, NULL), + __ATTR(flash_blocks_num, 0444, c2port_show_flash_blocks_num, NULL), + __ATTR(flash_block_size, 0444, c2port_show_flash_block_size, NULL), + __ATTR(flash_size, 0444, c2port_show_flash_size, NULL), + __ATTR(access, 0644, c2port_show_access, c2port_store_access), + __ATTR(reset, 0200, NULL, c2port_store_reset), + __ATTR(dev_id, 0444, c2port_show_dev_id, NULL), + __ATTR(rev_id, 0444, c2port_show_rev_id, NULL), + + __ATTR(flash_access, 0644, c2port_show_flash_access, + c2port_store_flash_access), + __ATTR(flash_erase, 0200, NULL, c2port_store_flash_erase), + __ATTR_NULL, +}; + +static struct bin_attribute c2port_bin_attrs = { + .attr = { + .name = "flash_data", + .mode = 0644 + }, + .read = c2port_read_flash_data, + .write = c2port_write_flash_data, + /* .size is computed at run-time */ +}; + +/* + * Exported functions + */ + +struct c2port_device *c2port_device_register(char *name, + struct c2port_ops *ops, void *devdata) +{ + struct c2port_device *c2dev; + int id, ret; + + if (unlikely(!ops) || unlikely(!ops->access) || \ + unlikely(!ops->c2d_dir) || unlikely(!ops->c2ck_set) || \ + unlikely(!ops->c2d_get) || unlikely(!ops->c2d_set)) + return ERR_PTR(-EINVAL); + + c2dev = kmalloc(sizeof(struct c2port_device), GFP_KERNEL); + if (unlikely(!c2dev)) + return ERR_PTR(-ENOMEM); + + ret = idr_pre_get(&c2port_idr, GFP_KERNEL); + if (!ret) { + ret = -ENOMEM; + goto error_idr_get_new; + } + + spin_lock_irq(&c2port_idr_lock); + ret = idr_get_new(&c2port_idr, c2dev, &id); + spin_unlock_irq(&c2port_idr_lock); + + if (ret < 0) + goto error_idr_get_new; + c2dev->id = id; + + c2dev->dev = device_create(c2port_class, NULL, 0, c2dev, + "c2port%d", id); + if (unlikely(!c2dev->dev)) { + ret = -ENOMEM; + goto error_device_create; + } + dev_set_drvdata(c2dev->dev, c2dev); + + strncpy(c2dev->name, name, C2PORT_NAME_LEN); + c2dev->ops = ops; + mutex_init(&c2dev->mutex); + + /* Create binary file */ + c2port_bin_attrs.size = ops->blocks_num * ops->block_size; + ret = device_create_bin_file(c2dev->dev, &c2port_bin_attrs); + if (unlikely(ret)) + goto error_device_create_bin_file; + + /* By default C2 port access is off */ + c2dev->access = c2dev->flash_access = 0; + ops->access(c2dev, 0); + + dev_info(c2dev->dev, "C2 port %s added\n", name); + dev_info(c2dev->dev, "%s flash has %d blocks x %d bytes " + "(%d bytes total)\n", + name, ops->blocks_num, ops->block_size, + ops->blocks_num * ops->block_size); + + return c2dev; + +error_device_create_bin_file: + device_destroy(c2port_class, 0); + +error_device_create: + spin_lock_irq(&c2port_idr_lock); + idr_remove(&c2port_idr, id); + spin_unlock_irq(&c2port_idr_lock); + +error_idr_get_new: + kfree(c2dev); + + return ERR_PTR(ret); +} +EXPORT_SYMBOL(c2port_device_register); + +void c2port_device_unregister(struct c2port_device *c2dev) +{ + if (!c2dev) + return; + + dev_info(c2dev->dev, "C2 port %s removed\n", c2dev->name); + + device_remove_bin_file(c2dev->dev, &c2port_bin_attrs); + spin_lock_irq(&c2port_idr_lock); + idr_remove(&c2port_idr, c2dev->id); + spin_unlock_irq(&c2port_idr_lock); + + device_destroy(c2port_class, c2dev->id); + + kfree(c2dev); +} +EXPORT_SYMBOL(c2port_device_unregister); + +/* + * Module stuff + */ + +static int __init c2port_init(void) +{ + printk(KERN_INFO "Silicon Labs C2 port support v. " DRIVER_VERSION + " - (C) 2007 Rodolfo Giometti\n"); + + c2port_class = class_create(THIS_MODULE, "c2port"); + if (!c2port_class) { + printk(KERN_ERR "c2port: failed to allocate class\n"); + return -ENOMEM; + } + c2port_class->dev_attrs = c2port_attrs; + + return 0; +} + +static void __exit c2port_exit(void) +{ + class_destroy(c2port_class); +} + +module_init(c2port_init); +module_exit(c2port_exit); + +MODULE_AUTHOR("Rodolfo Giometti <giometti@linux.it>"); +MODULE_DESCRIPTION("Silicon Labs C2 port support v. " DRIVER_VERSION); +MODULE_LICENSE("GPL"); |