diff options
Diffstat (limited to 'drivers/mtd/nand/Kconfig')
| -rw-r--r-- | drivers/mtd/nand/Kconfig | 41 |
1 files changed, 27 insertions, 14 deletions
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 5076faf9ca6..02f9cc30d77 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -1,5 +1,4 @@ # drivers/mtd/nand/Kconfig -# $Id: Kconfig,v 1.35 2005/11/07 11:14:30 gleixner Exp $ menuconfig MTD_NAND tristate "NAND Device Support" @@ -105,11 +104,24 @@ config MTD_NAND_BF5XX config MTD_NAND_BF5XX_HWECC bool "BF5XX NAND Hardware ECC" + default y depends on MTD_NAND_BF5XX help Enable the use of the BF5XX's internal ECC generator when using NAND. +config MTD_NAND_BF5XX_BOOTROM_ECC + bool "Use Blackfin BootROM ECC Layout" + default n + depends on MTD_NAND_BF5XX_HWECC + help + If you wish to modify NAND pages and allow the Blackfin on-chip + BootROM to boot from them, say Y here. This is only necessary + if you are booting U-Boot out of NAND and you wish to update + U-Boot from Linux' userspace. Otherwise, you should say N here. + + If unsure, say N. + config MTD_NAND_RTC_FROM4 tristate "Renesas Flash ROM 4-slot interface board (FROM_BOARD4)" depends on SH_SOLUTION_ENGINE @@ -272,22 +284,23 @@ config MTD_NAND_CS553X If you say "m", the module will be called "cs553x_nand.ko". -config MTD_NAND_AT91 - bool "Support for NAND Flash / SmartMedia on AT91" - depends on ARCH_AT91 +config MTD_NAND_ATMEL + tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32" + depends on ARCH_AT91 || AVR32 help Enables support for NAND Flash / Smart Media Card interface - on Atmel AT91 processors. + on Atmel AT91 and AVR32 processors. choice - prompt "ECC management for NAND Flash / SmartMedia on AT91" - depends on MTD_NAND_AT91 + prompt "ECC management for NAND Flash / SmartMedia on AT91 / AVR32" + depends on MTD_NAND_ATMEL -config MTD_NAND_AT91_ECC_HW +config MTD_NAND_ATMEL_ECC_HW bool "Hardware ECC" - depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9260 + depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9260 || AVR32 help - Uses hardware ECC provided by the at91sam9260/at91sam9263 chip - instead of software ECC. + Use hardware ECC instead of software ECC when the chip + supports it. + The hardware ECC controller is capable of single bit error correction and 2-bit random detection per page. @@ -297,16 +310,16 @@ config MTD_NAND_AT91_ECC_HW If unsure, say Y -config MTD_NAND_AT91_ECC_SOFT +config MTD_NAND_ATMEL_ECC_SOFT bool "Software ECC" help - Uses software ECC. + Use software ECC. NB : hardware and software ECC schemes are incompatible. If you switch from one to another, you'll have to erase your mtd partition. -config MTD_NAND_AT91_ECC_NONE +config MTD_NAND_ATMEL_ECC_NONE bool "No ECC (testing only, DANGEROUS)" depends on DEBUG_KERNEL help |