diff options
Diffstat (limited to 'drivers/net/wireless/ath/ath5k/phy.c')
| -rw-r--r-- | drivers/net/wireless/ath/ath5k/phy.c | 18 |
1 files changed, 9 insertions, 9 deletions
diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c index 7e2867689e1..e00ab5a6694 100644 --- a/drivers/net/wireless/ath/ath5k/phy.c +++ b/drivers/net/wireless/ath/ath5k/phy.c @@ -363,7 +363,7 @@ int ath5k_hw_rfgain_opt_init(struct ath5k_hw *ah) return 0; } -/* Schedule a gain probe check on the next transmited packet. +/* Schedule a gain probe check on the next transmitted packet. * That means our next packet is going to be sent with lower * tx power and a Peak to Average Power Detector (PAPD) will try * to measure the gain. @@ -620,7 +620,7 @@ enum ath5k_rfgain ath5k_hw_gainf_calibrate(struct ath5k_hw *ah) /* Check if measurement is ok and if we need * to adjust gain, schedule a gain adjustment, - * else switch back to the acive state */ + * else switch back to the active state */ if (ath5k_hw_rf_check_gainf_readback(ah) && AR5K_GAIN_CHECK_ADJUST(&ah->ah_gain) && ath5k_hw_rf_gainf_adjust(ah)) { @@ -807,7 +807,7 @@ static int ath5k_hw_rfregs_init(struct ath5k_hw *ah, * use b_OB and b_DB parameters stored * in eeprom on ee->ee_ob[ee_mode][0] * - * For all other chips we use OB/DB for 2Ghz + * For all other chips we use OB/DB for 2GHz * stored in the b/g modal section just like * 802.11a on ee->ee_ob[ee_mode][1] */ if ((ah->ah_radio == AR5K_RF5111) || @@ -1259,7 +1259,7 @@ static int ath5k_hw_channel(struct ath5k_hw *ah, { int ret; /* - * Check bounds supported by the PHY (we don't care about regultory + * Check bounds supported by the PHY (we don't care about regulatory * restrictions at this point). Note: hw_value already has the band * (CHANNEL_2GHZ, or CHANNEL_5GHZ) so we inform ath5k_channel_ok() * of the band by that */ @@ -1815,7 +1815,7 @@ ath5k_hw_set_spur_mitigation_filter(struct ath5k_hw *ah, } else if (ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_SPUR_FILT_EN) { - /* Clean up spur mitigation settings and disable fliter */ + /* Clean up spur mitigation settings and disable filter */ AR5K_REG_WRITE_BITS(ah, AR5K_PHY_BIN_MASK_CTL, AR5K_PHY_BIN_MASK_CTL_RATE, 0); AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_IQ, @@ -2510,8 +2510,8 @@ ath5k_combine_linear_pcdac_curves(struct ath5k_hw *ah, s16* table_min, s16 max_pwr_idx; s16 min_pwr_idx; s16 mid_pwr_idx = 0; - /* Edge flag turs on the 7nth bit on the PCDAC - * to delcare the higher power curve (force values + /* Edge flag turns on the 7nth bit on the PCDAC + * to declare the higher power curve (force values * to be greater than 64). If we only have one curve * we don't need to set this, if we have 2 curves and * fill the table backwards this can also be used to @@ -2568,7 +2568,7 @@ ath5k_combine_linear_pcdac_curves(struct ath5k_hw *ah, s16* table_min, } /* Don't go below 1, extrapolate below if we have - * already swithced to the lower power curve -or + * already switched to the lower power curve -or * we only have one curve and edge_flag is zero * anyway */ if (pcdac_tmp[pwr] < 1 && (edge_flag == 0x00)) { @@ -2805,7 +2805,7 @@ ath5k_write_pwr_to_pdadc_table(struct ath5k_hw *ah, u8 ee_mode) /* * This is the main function that uses all of the above * to set PCDAC/PDADC table on hw for the current channel. - * This table is used for tx power calibration on the basband, + * This table is used for tx power calibration on the baseband, * without it we get weird tx power levels and in some cases * distorted spectral mask */ |