diff options
Diffstat (limited to 'drivers/net/wireless/ath/ath5k/reset.c')
| -rw-r--r-- | drivers/net/wireless/ath/ath5k/reset.c | 33 |
1 files changed, 11 insertions, 22 deletions
diff --git a/drivers/net/wireless/ath/ath5k/reset.c b/drivers/net/wireless/ath/ath5k/reset.c index 34e13c70084..62954fc7786 100644 --- a/drivers/net/wireless/ath/ath5k/reset.c +++ b/drivers/net/wireless/ath/ath5k/reset.c @@ -25,6 +25,8 @@ Reset functions and helpers \*****************************/ +#include <asm/unaligned.h> + #include <linux/pci.h> /* To determine if a card is pci-e */ #include <linux/log2.h> #include "ath5k.h" @@ -870,6 +872,7 @@ static void ath5k_hw_commit_eeprom_settings(struct ath5k_hw *ah, int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, struct ieee80211_channel *channel, bool change_channel) { + struct ath_common *common = ath5k_hw_common(ah); u32 s_seq[10], s_ant, s_led[3], staid1_flags, tsf_up, tsf_lo; u32 phy_tst1; u8 mode, freq, ee_mode, ant[2]; @@ -1171,10 +1174,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, ath5k_hw_reg_write(ah, s_led[2], AR5K_GPIODO); /* Restore sta_id flags and preserve our mac address*/ - ath5k_hw_reg_write(ah, AR5K_LOW_ID(ah->ah_sta_id), - AR5K_STA_ID0); - ath5k_hw_reg_write(ah, staid1_flags | AR5K_HIGH_ID(ah->ah_sta_id), - AR5K_STA_ID1); + ath5k_hw_reg_write(ah, + get_unaligned_le32(common->macaddr), + AR5K_STA_ID0); + ath5k_hw_reg_write(ah, + staid1_flags | get_unaligned_le16(common->macaddr + 4), + AR5K_STA_ID1); /* @@ -1182,8 +1187,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, */ /* Restore bssid and bssid mask */ - /* XXX: add ah->aid once mac80211 gives this to us */ - ath5k_hw_set_associd(ah, ah->ah_bssid, 0); + ath5k_hw_set_associd(ah); /* Set PCU config */ ath5k_hw_set_opmode(ah); @@ -1289,7 +1293,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, * out and/or noise floor calibration might timeout. */ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, - AR5K_PHY_AGCCTL_CAL); + AR5K_PHY_AGCCTL_CAL | AR5K_PHY_AGCCTL_NF); /* At the same time start I/Q calibration for QAM constellation * -no need for CCK- */ @@ -1310,21 +1314,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, channel->center_freq); } - /* - * If we run NF calibration before AGC, it always times out. - * Binary HAL starts NF and AGC calibration at the same time - * and only waits for AGC to finish. Also if AGC or NF cal. - * times out, reset doesn't fail on binary HAL. I believe - * that's wrong because since rx path is routed to a detector, - * if cal. doesn't finish we won't have RX. Sam's HAL for AR5210/5211 - * enables noise floor calibration after offset calibration and if noise - * floor calibration fails, reset fails. I believe that's - * a better approach, we just need to find a polling interval - * that suits best, even if reset continues we need to make - * sure that rx path is ready. - */ - ath5k_hw_noise_floor_calibration(ah, channel->center_freq); - /* Restore antenna mode */ ath5k_hw_set_antenna_mode(ah, ah->ah_ant_mode); |