diff options
Diffstat (limited to 'drivers/scsi/aic7xxx/aiclib.h')
| -rw-r--r-- | drivers/scsi/aic7xxx/aiclib.h | 868 |
1 files changed, 0 insertions, 868 deletions
diff --git a/drivers/scsi/aic7xxx/aiclib.h b/drivers/scsi/aic7xxx/aiclib.h index bfe6f954d3c..e7d94cbaf2a 100644 --- a/drivers/scsi/aic7xxx/aiclib.h +++ b/drivers/scsi/aic7xxx/aiclib.h @@ -57,121 +57,6 @@ #ifndef _AICLIB_H #define _AICLIB_H -/* - * Linux Interrupt Support. - */ -#ifndef IRQ_RETVAL -typedef void irqreturn_t; -#define IRQ_RETVAL(x) -#endif - -/* - * SCSI command format - */ - -/* - * Define dome bits that are in ALL (or a lot of) scsi commands - */ -#define SCSI_CTL_LINK 0x01 -#define SCSI_CTL_FLAG 0x02 -#define SCSI_CTL_VENDOR 0xC0 -#define SCSI_CMD_LUN 0xA0 /* these two should not be needed */ -#define SCSI_CMD_LUN_SHIFT 5 /* LUN in the cmd is no longer SCSI */ - -#define SCSI_MAX_CDBLEN 16 /* - * 16 byte commands are in the - * SCSI-3 spec - */ -/* 6byte CDBs special case 0 length to be 256 */ -#define SCSI_CDB6_LEN(len) ((len) == 0 ? 256 : len) - -/* - * This type defines actions to be taken when a particular sense code is - * received. Right now, these flags are only defined to take up 16 bits, - * but can be expanded in the future if necessary. - */ -typedef enum { - SS_NOP = 0x000000, /* Do nothing */ - SS_RETRY = 0x010000, /* Retry the command */ - SS_FAIL = 0x020000, /* Bail out */ - SS_START = 0x030000, /* Send a Start Unit command to the device, - * then retry the original command. - */ - SS_TUR = 0x040000, /* Send a Test Unit Ready command to the - * device, then retry the original command. - */ - SS_REQSENSE = 0x050000, /* Send a RequestSense command to the - * device, then retry the original command. - */ - SS_INQ_REFRESH = 0x060000, - SS_MASK = 0xff0000 -} aic_sense_action; - -typedef enum { - SSQ_NONE = 0x0000, - SSQ_DECREMENT_COUNT = 0x0100, /* Decrement the retry count */ - SSQ_MANY = 0x0200, /* send lots of recovery commands */ - SSQ_RANGE = 0x0400, /* - * This table entry represents the - * end of a range of ASCQs that - * have identical error actions - * and text. - */ - SSQ_PRINT_SENSE = 0x0800, - SSQ_DELAY = 0x1000, /* Delay before retry. */ - SSQ_DELAY_RANDOM = 0x2000, /* Randomized delay before retry. */ - SSQ_FALLBACK = 0x4000, /* Do a speed fallback to recover */ - SSQ_MASK = 0xff00 -} aic_sense_action_qualifier; - -/* Mask for error status values */ -#define SS_ERRMASK 0xff - -/* The default, retyable, error action */ -#define SS_RDEF SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE|EIO - -/* The retyable, error action, with table specified error code */ -#define SS_RET SS_RETRY|SSQ_DECREMENT_COUNT|SSQ_PRINT_SENSE - -/* Fatal error action, with table specified error code */ -#define SS_FATAL SS_FAIL|SSQ_PRINT_SENSE - -struct scsi_generic -{ - uint8_t opcode; - uint8_t bytes[11]; -}; - -struct scsi_request_sense -{ - uint8_t opcode; - uint8_t byte2; - uint8_t unused[2]; - uint8_t length; - uint8_t control; -}; - -struct scsi_test_unit_ready -{ - uint8_t opcode; - uint8_t byte2; - uint8_t unused[3]; - uint8_t control; -}; - -struct scsi_send_diag -{ - uint8_t opcode; - uint8_t byte2; -#define SSD_UOL 0x01 -#define SSD_DOL 0x02 -#define SSD_SELFTEST 0x04 -#define SSD_PF 0x10 - uint8_t unused[1]; - uint8_t paramlen[2]; - uint8_t control; -}; - struct scsi_sense { uint8_t opcode; @@ -181,537 +66,12 @@ struct scsi_sense uint8_t control; }; -struct scsi_inquiry -{ - uint8_t opcode; - uint8_t byte2; -#define SI_EVPD 0x01 - uint8_t page_code; - uint8_t reserved; - uint8_t length; - uint8_t control; -}; - -struct scsi_mode_sense_6 -{ - uint8_t opcode; - uint8_t byte2; -#define SMS_DBD 0x08 - uint8_t page; -#define SMS_PAGE_CODE 0x3F -#define SMS_VENDOR_SPECIFIC_PAGE 0x00 -#define SMS_DISCONNECT_RECONNECT_PAGE 0x02 -#define SMS_PERIPHERAL_DEVICE_PAGE 0x09 -#define SMS_CONTROL_MODE_PAGE 0x0A -#define SMS_ALL_PAGES_PAGE 0x3F -#define SMS_PAGE_CTRL_MASK 0xC0 -#define SMS_PAGE_CTRL_CURRENT 0x00 -#define SMS_PAGE_CTRL_CHANGEABLE 0x40 -#define SMS_PAGE_CTRL_DEFAULT 0x80 -#define SMS_PAGE_CTRL_SAVED 0xC0 - uint8_t unused; - uint8_t length; - uint8_t control; -}; - -struct scsi_mode_sense_10 -{ - uint8_t opcode; - uint8_t byte2; /* same bits as small version */ - uint8_t page; /* same bits as small version */ - uint8_t unused[4]; - uint8_t length[2]; - uint8_t control; -}; - -struct scsi_mode_select_6 -{ - uint8_t opcode; - uint8_t byte2; -#define SMS_SP 0x01 -#define SMS_PF 0x10 - uint8_t unused[2]; - uint8_t length; - uint8_t control; -}; - -struct scsi_mode_select_10 -{ - uint8_t opcode; - uint8_t byte2; /* same bits as small version */ - uint8_t unused[5]; - uint8_t length[2]; - uint8_t control; -}; - -/* - * When sending a mode select to a tape drive, the medium type must be 0. - */ -struct scsi_mode_hdr_6 -{ - uint8_t datalen; - uint8_t medium_type; - uint8_t dev_specific; - uint8_t block_descr_len; -}; - -struct scsi_mode_hdr_10 -{ - uint8_t datalen[2]; - uint8_t medium_type; - uint8_t dev_specific; - uint8_t reserved[2]; - uint8_t block_descr_len[2]; -}; - -struct scsi_mode_block_descr -{ - uint8_t density_code; - uint8_t num_blocks[3]; - uint8_t reserved; - uint8_t block_len[3]; -}; - -struct scsi_log_sense -{ - uint8_t opcode; - uint8_t byte2; -#define SLS_SP 0x01 -#define SLS_PPC 0x02 - uint8_t page; -#define SLS_PAGE_CODE 0x3F -#define SLS_ALL_PAGES_PAGE 0x00 -#define SLS_OVERRUN_PAGE 0x01 -#define SLS_ERROR_WRITE_PAGE 0x02 -#define SLS_ERROR_READ_PAGE 0x03 -#define SLS_ERROR_READREVERSE_PAGE 0x04 -#define SLS_ERROR_VERIFY_PAGE 0x05 -#define SLS_ERROR_NONMEDIUM_PAGE 0x06 -#define SLS_ERROR_LASTN_PAGE 0x07 -#define SLS_PAGE_CTRL_MASK 0xC0 -#define SLS_PAGE_CTRL_THRESHOLD 0x00 -#define SLS_PAGE_CTRL_CUMULATIVE 0x40 -#define SLS_PAGE_CTRL_THRESH_DEFAULT 0x80 -#define SLS_PAGE_CTRL_CUMUL_DEFAULT 0xC0 - uint8_t reserved[2]; - uint8_t paramptr[2]; - uint8_t length[2]; - uint8_t control; -}; - -struct scsi_log_select -{ - uint8_t opcode; - uint8_t byte2; -/* SLS_SP 0x01 */ -#define SLS_PCR 0x02 - uint8_t page; -/* SLS_PAGE_CTRL_MASK 0xC0 */ -/* SLS_PAGE_CTRL_THRESHOLD 0x00 */ -/* SLS_PAGE_CTRL_CUMULATIVE 0x40 */ -/* SLS_PAGE_CTRL_THRESH_DEFAULT 0x80 */ -/* SLS_PAGE_CTRL_CUMUL_DEFAULT 0xC0 */ - uint8_t reserved[4]; - uint8_t length[2]; - uint8_t control; -}; - -struct scsi_log_header -{ - uint8_t page; - uint8_t reserved; - uint8_t datalen[2]; -}; - -struct scsi_log_param_header { - uint8_t param_code[2]; - uint8_t param_control; -#define SLP_LP 0x01 -#define SLP_LBIN 0x02 -#define SLP_TMC_MASK 0x0C -#define SLP_TMC_ALWAYS 0x00 -#define SLP_TMC_EQUAL 0x04 -#define SLP_TMC_NOTEQUAL 0x08 -#define SLP_TMC_GREATER 0x0C -#define SLP_ETC 0x10 -#define SLP_TSD 0x20 -#define SLP_DS 0x40 -#define SLP_DU 0x80 - uint8_t param_len; -}; - -struct scsi_control_page { - uint8_t page_code; - uint8_t page_length; - uint8_t rlec; -#define SCB_RLEC 0x01 /*Report Log Exception Cond*/ - uint8_t queue_flags; -#define SCP_QUEUE_ALG_MASK 0xF0 -#define SCP_QUEUE_ALG_RESTRICTED 0x00 -#define SCP_QUEUE_ALG_UNRESTRICTED 0x10 -#define SCP_QUEUE_ERR 0x02 /*Queued I/O aborted for CACs*/ -#define SCP_QUEUE_DQUE 0x01 /*Queued I/O disabled*/ - uint8_t eca_and_aen; -#define SCP_EECA 0x80 /*Enable Extended CA*/ -#define SCP_RAENP 0x04 /*Ready AEN Permission*/ -#define SCP_UAAENP 0x02 /*UA AEN Permission*/ -#define SCP_EAENP 0x01 /*Error AEN Permission*/ - uint8_t reserved; - uint8_t aen_holdoff_period[2]; -}; - -struct scsi_reserve -{ - uint8_t opcode; - uint8_t byte2; - uint8_t unused[2]; - uint8_t length; - uint8_t control; -}; - -struct scsi_release -{ - uint8_t opcode; - uint8_t byte2; - uint8_t unused[2]; - uint8_t length; - uint8_t control; -}; - -struct scsi_prevent -{ - uint8_t opcode; - uint8_t byte2; - uint8_t unused[2]; - uint8_t how; - uint8_t control; -}; -#define PR_PREVENT 0x01 -#define PR_ALLOW 0x00 - -struct scsi_sync_cache -{ - uint8_t opcode; - uint8_t byte2; - uint8_t begin_lba[4]; - uint8_t reserved; - uint8_t lb_count[2]; - uint8_t control; -}; - - -struct scsi_changedef -{ - uint8_t opcode; - uint8_t byte2; - uint8_t unused1; - uint8_t how; - uint8_t unused[4]; - uint8_t datalen; - uint8_t control; -}; - -struct scsi_read_buffer -{ - uint8_t opcode; - uint8_t byte2; -#define RWB_MODE 0x07 -#define RWB_MODE_HDR_DATA 0x00 -#define RWB_MODE_DATA 0x02 -#define RWB_MODE_DOWNLOAD 0x04 -#define RWB_MODE_DOWNLOAD_SAVE 0x05 - uint8_t buffer_id; - uint8_t offset[3]; - uint8_t length[3]; - uint8_t control; -}; - -struct scsi_write_buffer -{ - uint8_t opcode; - uint8_t byte2; - uint8_t buffer_id; - uint8_t offset[3]; - uint8_t length[3]; - uint8_t control; -}; - -struct scsi_rw_6 -{ - uint8_t opcode; - uint8_t addr[3]; -/* only 5 bits are valid in the MSB address byte */ -#define SRW_TOPADDR 0x1F - uint8_t length; - uint8_t control; -}; - -struct scsi_rw_10 -{ - uint8_t opcode; -#define SRW10_RELADDR 0x01 -#define SRW10_FUA 0x08 -#define SRW10_DPO 0x10 - uint8_t byte2; - uint8_t addr[4]; - uint8_t reserved; - uint8_t length[2]; - uint8_t control; -}; - -struct scsi_rw_12 -{ - uint8_t opcode; -#define SRW12_RELADDR 0x01 -#define SRW12_FUA 0x08 -#define SRW12_DPO 0x10 - uint8_t byte2; - uint8_t addr[4]; - uint8_t length[4]; - uint8_t reserved; - uint8_t control; -}; - -struct scsi_start_stop_unit -{ - uint8_t opcode; - uint8_t byte2; -#define SSS_IMMED 0x01 - uint8_t reserved[2]; - uint8_t how; -#define SSS_START 0x01 -#define SSS_LOEJ 0x02 - uint8_t control; -}; - -#define SC_SCSI_1 0x01 -#define SC_SCSI_2 0x03 - -/* - * Opcodes - */ - -#define TEST_UNIT_READY 0x00 -#define REQUEST_SENSE 0x03 -#define READ_6 0x08 -#define WRITE_6 0x0a -#define INQUIRY 0x12 -#define MODE_SELECT_6 0x15 -#define MODE_SENSE_6 0x1a -#define START_STOP_UNIT 0x1b -#define START_STOP 0x1b -#define RESERVE 0x16 -#define RELEASE 0x17 -#define RECEIVE_DIAGNOSTIC 0x1c -#define SEND_DIAGNOSTIC 0x1d -#define PREVENT_ALLOW 0x1e -#define READ_CAPACITY 0x25 -#define READ_10 0x28 -#define WRITE_10 0x2a -#define POSITION_TO_ELEMENT 0x2b -#define SYNCHRONIZE_CACHE 0x35 -#define WRITE_BUFFER 0x3b -#define READ_BUFFER 0x3c -#define CHANGE_DEFINITION 0x40 -#define LOG_SELECT 0x4c -#define LOG_SENSE 0x4d -#ifdef XXXCAM -#define MODE_SENSE_10 0x5A -#endif -#define MODE_SELECT_10 0x55 -#define MOVE_MEDIUM 0xa5 -#define READ_12 0xa8 -#define WRITE_12 0xaa -#define READ_ELEMENT_STATUS 0xb8 - - -/* - * Device Types - */ -#define T_DIRECT 0x00 -#define T_SEQUENTIAL 0x01 -#define T_PRINTER 0x02 -#define T_PROCESSOR 0x03 -#define T_WORM 0x04 -#define T_CDROM 0x05 -#define T_SCANNER 0x06 -#define T_OPTICAL 0x07 -#define T_CHANGER 0x08 -#define T_COMM 0x09 -#define T_ASC0 0x0a -#define T_ASC1 0x0b -#define T_STORARRAY 0x0c -#define T_ENCLOSURE 0x0d -#define T_RBC 0x0e -#define T_OCRW 0x0f -#define T_NODEVICE 0x1F -#define T_ANY 0xFF /* Used in Quirk table matches */ - -#define T_REMOV 1 -#define T_FIXED 0 - -/* - * This length is the initial inquiry length used by the probe code, as - * well as the legnth necessary for aic_print_inquiry() to function - * correctly. If either use requires a different length in the future, - * the two values should be de-coupled. - */ -#define SHORT_INQUIRY_LENGTH 36 - -struct scsi_inquiry_data -{ - uint8_t device; -#define SID_TYPE(inq_data) ((inq_data)->device & 0x1f) -#define SID_QUAL(inq_data) (((inq_data)->device & 0xE0) >> 5) -#define SID_QUAL_LU_CONNECTED 0x00 /* - * The specified peripheral device - * type is currently connected to - * logical unit. If the target cannot - * determine whether or not a physical - * device is currently connected, it - * shall also use this peripheral - * qualifier when returning the INQUIRY - * data. This peripheral qualifier - * does not mean that the device is - * ready for access by the initiator. - */ -#define SID_QUAL_LU_OFFLINE 0x01 /* - * The target is capable of supporting - * the specified peripheral device type - * on this logical unit; however, the - * physical device is not currently - * connected to this logical unit. - */ -#define SID_QUAL_RSVD 0x02 -#define SID_QUAL_BAD_LU 0x03 /* - * The target is not capable of - * supporting a physical device on - * this logical unit. For this - * peripheral qualifier the peripheral - * device type shall be set to 1Fh to - * provide compatibility with previous - * versions of SCSI. All other - * peripheral device type values are - * reserved for this peripheral - * qualifier. - */ -#define SID_QUAL_IS_VENDOR_UNIQUE(inq_data) ((SID_QUAL(inq_data) & 0x08) != 0) - uint8_t dev_qual2; -#define SID_QUAL2 0x7F -#define SID_IS_REMOVABLE(inq_data) (((inq_data)->dev_qual2 & 0x80) != 0) - uint8_t version; -#define SID_ANSI_REV(inq_data) ((inq_data)->version & 0x07) #define SCSI_REV_0 0 #define SCSI_REV_CCS 1 #define SCSI_REV_2 2 #define SCSI_REV_SPC 3 #define SCSI_REV_SPC2 4 -#define SID_ECMA 0x38 -#define SID_ISO 0xC0 - uint8_t response_format; -#define SID_AENC 0x80 -#define SID_TrmIOP 0x40 - uint8_t additional_length; - uint8_t reserved[2]; - uint8_t flags; -#define SID_SftRe 0x01 -#define SID_CmdQue 0x02 -#define SID_Linked 0x08 -#define SID_Sync 0x10 -#define SID_WBus16 0x20 -#define SID_WBus32 0x40 -#define SID_RelAdr 0x80 -#define SID_VENDOR_SIZE 8 - char vendor[SID_VENDOR_SIZE]; -#define SID_PRODUCT_SIZE 16 - char product[SID_PRODUCT_SIZE]; -#define SID_REVISION_SIZE 4 - char revision[SID_REVISION_SIZE]; - /* - * The following fields were taken from SCSI Primary Commands - 2 - * (SPC-2) Revision 14, Dated 11 November 1999 - */ -#define SID_VENDOR_SPECIFIC_0_SIZE 20 - uint8_t vendor_specific0[SID_VENDOR_SPECIFIC_0_SIZE]; - /* - * An extension of SCSI Parallel Specific Values - */ -#define SID_SPI_IUS 0x01 -#define SID_SPI_QAS 0x02 -#define SID_SPI_CLOCK_ST 0x00 -#define SID_SPI_CLOCK_DT 0x04 -#define SID_SPI_CLOCK_DT_ST 0x0C -#define SID_SPI_MASK 0x0F - uint8_t spi3data; - uint8_t reserved2; - /* - * Version Descriptors, stored 2 byte values. - */ - uint8_t version1[2]; - uint8_t version2[2]; - uint8_t version3[2]; - uint8_t version4[2]; - uint8_t version5[2]; - uint8_t version6[2]; - uint8_t version7[2]; - uint8_t version8[2]; - - uint8_t reserved3[22]; - -#define SID_VENDOR_SPECIFIC_1_SIZE 160 - uint8_t vendor_specific1[SID_VENDOR_SPECIFIC_1_SIZE]; -}; - -struct scsi_vpd_unit_serial_number -{ - uint8_t device; - uint8_t page_code; -#define SVPD_UNIT_SERIAL_NUMBER 0x80 - uint8_t reserved; - uint8_t length; /* serial number length */ -#define SVPD_SERIAL_NUM_SIZE 251 - uint8_t serial_num[SVPD_SERIAL_NUM_SIZE]; -}; - -struct scsi_read_capacity -{ - uint8_t opcode; - uint8_t byte2; - uint8_t addr[4]; - uint8_t unused[3]; - uint8_t control; -}; - -struct scsi_read_capacity_data -{ - uint8_t addr[4]; - uint8_t length[4]; -}; - -struct scsi_report_luns -{ - uint8_t opcode; - uint8_t byte2; - uint8_t unused[3]; - uint8_t addr[4]; - uint8_t control; -}; - -struct scsi_report_luns_data { - uint8_t length[4]; /* length of LUN inventory, in bytes */ - uint8_t reserved[4]; /* unused */ - /* - * LUN inventory- we only support the type zero form for now. - */ - struct { - uint8_t lundata[8]; - } luns[1]; -}; -#define RPL_LUNDATA_ATYP_MASK 0xc0 /* MBZ for type 0 lun */ -#define RPL_LUNDATA_T0LUN 1 /* @ lundata[1] */ - - struct scsi_sense_data { uint8_t error_code; @@ -757,41 +117,6 @@ struct scsi_sense_data #define SSD_FULL_SIZE sizeof(struct scsi_sense_data) }; -struct scsi_mode_header_6 -{ - uint8_t data_length; /* Sense data length */ - uint8_t medium_type; - uint8_t dev_spec; - uint8_t blk_desc_len; -}; - -struct scsi_mode_header_10 -{ - uint8_t data_length[2];/* Sense data length */ - uint8_t medium_type; - uint8_t dev_spec; - uint8_t unused[2]; - uint8_t blk_desc_len[2]; -}; - -struct scsi_mode_page_header -{ - uint8_t page_code; - uint8_t page_length; -}; - -struct scsi_mode_blk_desc -{ - uint8_t density; - uint8_t nblocks[3]; - uint8_t reserved; - uint8_t blklen[3]; -}; - -#define SCSI_DEFAULT_DENSITY 0x00 /* use 'default' density */ -#define SCSI_SAME_DENSITY 0x7f /* use 'same' density- >= SCSI-2 only */ - - /* * Status Byte */ @@ -807,76 +132,7 @@ struct scsi_mode_blk_desc #define SCSI_STATUS_ACA_ACTIVE 0x30 #define SCSI_STATUS_TASK_ABORTED 0x40 -struct scsi_inquiry_pattern { - uint8_t type; - uint8_t media_type; -#define SIP_MEDIA_REMOVABLE 0x01 -#define SIP_MEDIA_FIXED 0x02 - const char *vendor; - const char *product; - const char *revision; -}; - -struct scsi_static_inquiry_pattern { - uint8_t type; - uint8_t media_type; - char vendor[SID_VENDOR_SIZE+1]; - char product[SID_PRODUCT_SIZE+1]; - char revision[SID_REVISION_SIZE+1]; -}; - -struct scsi_sense_quirk_entry { - struct scsi_inquiry_pattern inq_pat; - int num_sense_keys; - int num_ascs; - struct sense_key_table_entry *sense_key_info; - struct asc_table_entry *asc_info; -}; - -struct sense_key_table_entry { - uint8_t sense_key; - uint32_t action; - const char *desc; -}; - -struct asc_table_entry { - uint8_t asc; - uint8_t ascq; - uint32_t action; - const char *desc; -}; - -struct op_table_entry { - uint8_t opcode; - uint16_t opmask; - const char *desc; -}; - -struct scsi_op_quirk_entry { - struct scsi_inquiry_pattern inq_pat; - int num_ops; - struct op_table_entry *op_table; -}; - -typedef enum { - SSS_FLAG_NONE = 0x00, - SSS_FLAG_PRINT_COMMAND = 0x01 -} scsi_sense_string_flags; - -extern const char *scsi_sense_key_text[]; - /************************* Large Disk Handling ********************************/ -#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,0) -static __inline int aic_sector_div(u_long capacity, int heads, int sectors); - -static __inline int -aic_sector_div(u_long capacity, int heads, int sectors) -{ - return (capacity / (heads * sectors)); -} -#else -static __inline int aic_sector_div(sector_t capacity, int heads, int sectors); - static __inline int aic_sector_div(sector_t capacity, int heads, int sectors) { @@ -884,7 +140,6 @@ aic_sector_div(sector_t capacity, int heads, int sectors) sector_div(capacity, (heads * sectors)); return (int)capacity; } -#endif /**************************** Module Library Hack *****************************/ /* @@ -899,138 +154,15 @@ aic_sector_div(sector_t capacity, int heads, int sectors) #define AIC_LIB_ENTRY_EXPAND(x, prefix) AIC_LIB_ENTRY_CONCAT(x, prefix) #define AIC_LIB_ENTRY(x) AIC_LIB_ENTRY_EXPAND(x, AIC_LIB_PREFIX) -#define aic_sense_desc AIC_LIB_ENTRY(_sense_desc) -#define aic_sense_error_action AIC_LIB_ENTRY(_sense_error_action) -#define aic_error_action AIC_LIB_ENTRY(_error_action) -#define aic_op_desc AIC_LIB_ENTRY(_op_desc) -#define aic_cdb_string AIC_LIB_ENTRY(_cdb_string) -#define aic_print_inquiry AIC_LIB_ENTRY(_print_inquiry) #define aic_calc_syncsrate AIC_LIB_ENTRY(_calc_syncrate) -#define aic_calc_syncparam AIC_LIB_ENTRY(_calc_syncparam) -#define aic_calc_speed AIC_LIB_ENTRY(_calc_speed) -#define aic_inquiry_match AIC_LIB_ENTRY(_inquiry_match) -#define aic_static_inquiry_match AIC_LIB_ENTRY(_static_inquiry_match) -#define aic_parse_brace_option AIC_LIB_ENTRY(_parse_brace_option) - -/******************************************************************************/ - -void aic_sense_desc(int /*sense_key*/, int /*asc*/, - int /*ascq*/, struct scsi_inquiry_data*, - const char** /*sense_key_desc*/, - const char** /*asc_desc*/); -aic_sense_action aic_sense_error_action(struct scsi_sense_data*, - struct scsi_inquiry_data*, - uint32_t /*sense_flags*/); -uint32_t aic_error_action(struct scsi_cmnd *, - struct scsi_inquiry_data *, - cam_status, u_int); - -#define SF_RETRY_UA 0x01 -#define SF_NO_PRINT 0x02 -#define SF_QUIET_IR 0x04 /* Be quiet about Illegal Request reponses */ -#define SF_PRINT_ALWAYS 0x08 - - -const char * aic_op_desc(uint16_t /*opcode*/, struct scsi_inquiry_data*); -char * aic_cdb_string(uint8_t* /*cdb_ptr*/, char* /*cdb_string*/, - size_t /*len*/); -void aic_print_inquiry(struct scsi_inquiry_data*); u_int aic_calc_syncsrate(u_int /*period_factor*/); -u_int aic_calc_syncparam(u_int /*period*/); -u_int aic_calc_speed(u_int width, u_int period, u_int offset, - u_int min_rate); - -int aic_inquiry_match(caddr_t /*inqbuffer*/, - caddr_t /*table_entry*/); -int aic_static_inquiry_match(caddr_t /*inqbuffer*/, - caddr_t /*table_entry*/); typedef void aic_option_callback_t(u_long, int, int, int32_t); char * aic_parse_brace_option(char *opt_name, char *opt_arg, char *end, int depth, aic_option_callback_t *, u_long); -static __inline void scsi_extract_sense(struct scsi_sense_data *sense, - int *error_code, int *sense_key, - int *asc, int *ascq); -static __inline void scsi_ulto2b(uint32_t val, uint8_t *bytes); -static __inline void scsi_ulto3b(uint32_t val, uint8_t *bytes); -static __inline void scsi_ulto4b(uint32_t val, uint8_t *bytes); -static __inline uint32_t scsi_2btoul(uint8_t *bytes); -static __inline uint32_t scsi_3btoul(uint8_t *bytes); -static __inline int32_t scsi_3btol(uint8_t *bytes); -static __inline uint32_t scsi_4btoul(uint8_t *bytes); - -static __inline void scsi_extract_sense(struct scsi_sense_data *sense, - int *error_code, int *sense_key, - int *asc, int *ascq) -{ - *error_code = sense->error_code & SSD_ERRCODE; - *sense_key = sense->flags & SSD_KEY; - *asc = (sense->extra_len >= 5) ? sense->add_sense_code : 0; - *ascq = (sense->extra_len >= 6) ? sense->add_sense_code_qual : 0; -} - -static __inline void -scsi_ulto2b(uint32_t val, uint8_t *bytes) -{ - - bytes[0] = (val >> 8) & 0xff; - bytes[1] = val & 0xff; -} - -static __inline void -scsi_ulto3b(uint32_t val, uint8_t *bytes) -{ - - bytes[0] = (val >> 16) & 0xff; - bytes[1] = (val >> 8) & 0xff; - bytes[2] = val & 0xff; -} - -static __inline void -scsi_ulto4b(uint32_t val, uint8_t *bytes) -{ - - bytes[0] = (val >> 24) & 0xff; - bytes[1] = (val >> 16) & 0xff; - bytes[2] = (val >> 8) & 0xff; - bytes[3] = val & 0xff; -} - -static __inline uint32_t -scsi_2btoul(uint8_t *bytes) -{ - uint32_t rv; - - rv = (bytes[0] << 8) | - bytes[1]; - return (rv); -} - -static __inline uint32_t -scsi_3btoul(uint8_t *bytes) -{ - uint32_t rv; - - rv = (bytes[0] << 16) | - (bytes[1] << 8) | - bytes[2]; - return (rv); -} - -static __inline int32_t -scsi_3btol(uint8_t *bytes) -{ - uint32_t rc = scsi_3btoul(bytes); - - if (rc & 0x00800000) - rc |= 0xff000000; - - return (int32_t) rc; -} - static __inline uint32_t scsi_4btoul(uint8_t *bytes) { |