diff options
Diffstat (limited to 'drivers/scsi/isci/probe_roms.h')
| -rw-r--r-- | drivers/scsi/isci/probe_roms.h | 249 |
1 files changed, 249 insertions, 0 deletions
diff --git a/drivers/scsi/isci/probe_roms.h b/drivers/scsi/isci/probe_roms.h new file mode 100644 index 00000000000..dc007e692f4 --- /dev/null +++ b/drivers/scsi/isci/probe_roms.h @@ -0,0 +1,249 @@ +/* + * This file is provided under a dual BSD/GPLv2 license. When using or + * redistributing this file, you may do so under either license. + * + * GPL LICENSE SUMMARY + * + * Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of version 2 of the GNU General Public License as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + * The full GNU General Public License is included in this distribution + * in the file called LICENSE.GPL. + * + * BSD LICENSE + * + * Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Intel Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ +#ifndef _ISCI_PROBE_ROMS_H_ +#define _ISCI_PROBE_ROMS_H_ + +#ifdef __KERNEL__ +#include <linux/firmware.h> +#include <linux/pci.h> +#include <linux/efi.h> +#include "isci.h" + +#define SCIC_SDS_PARM_NO_SPEED 0 + +/* generation 1 (i.e. 1.5 Gb/s) */ +#define SCIC_SDS_PARM_GEN1_SPEED 1 + +/* generation 2 (i.e. 3.0 Gb/s) */ +#define SCIC_SDS_PARM_GEN2_SPEED 2 + +/* generation 3 (i.e. 6.0 Gb/s) */ +#define SCIC_SDS_PARM_GEN3_SPEED 3 +#define SCIC_SDS_PARM_MAX_SPEED SCIC_SDS_PARM_GEN3_SPEED + +/* parameters that can be set by module parameters */ +struct sci_user_parameters { + struct sci_phy_user_params { + /** + * This field specifies the NOTIFY (ENABLE SPIN UP) primitive + * insertion frequency for this phy index. + */ + u32 notify_enable_spin_up_insertion_frequency; + + /** + * This method specifies the number of transmitted DWORDs within which + * to transmit a single ALIGN primitive. This value applies regardless + * of what type of device is attached or connection state. A value of + * 0 indicates that no ALIGN primitives will be inserted. + */ + u16 align_insertion_frequency; + + /** + * This method specifies the number of transmitted DWORDs within which + * to transmit 2 ALIGN primitives. This applies for SAS connections + * only. A minimum value of 3 is required for this field. + */ + u16 in_connection_align_insertion_frequency; + + /** + * This field indicates the maximum speed generation to be utilized + * by phys in the supplied port. + * - A value of 1 indicates generation 1 (i.e. 1.5 Gb/s). + * - A value of 2 indicates generation 2 (i.e. 3.0 Gb/s). + * - A value of 3 indicates generation 3 (i.e. 6.0 Gb/s). + */ + u8 max_speed_generation; + + } phys[SCI_MAX_PHYS]; + + /** + * This field specifies the maximum number of direct attached devices + * that can have power supplied to them simultaneously. + */ + u8 max_number_concurrent_device_spin_up; + + /** + * This field specifies the number of seconds to allow a phy to consume + * power before yielding to another phy. + * + */ + u8 phy_spin_up_delay_interval; + + /** + * These timer values specifies how long a link will remain open with no + * activity in increments of a microsecond, it can be in increments of + * 100 microseconds if the upper most bit is set. + * + */ + u16 stp_inactivity_timeout; + u16 ssp_inactivity_timeout; + + /** + * These timer values specifies how long a link will remain open in increments + * of 100 microseconds. + * + */ + u16 stp_max_occupancy_timeout; + u16 ssp_max_occupancy_timeout; + + /** + * This timer value specifies how long a link will remain open with no + * outbound traffic in increments of a microsecond. + * + */ + u8 no_outbound_task_timeout; + +}; + +#define SCIC_SDS_PARM_PHY_MASK_MIN 0x0 +#define SCIC_SDS_PARM_PHY_MASK_MAX 0xF +#define MAX_CONCURRENT_DEVICE_SPIN_UP_COUNT 4 + +struct sci_oem_params; +int sci_oem_parameters_validate(struct sci_oem_params *oem); + +struct isci_orom; +struct isci_orom *isci_request_oprom(struct pci_dev *pdev); +enum sci_status isci_parse_oem_parameters(struct sci_oem_params *oem, + struct isci_orom *orom, int scu_index); +struct isci_orom *isci_request_firmware(struct pci_dev *pdev, const struct firmware *fw); +struct isci_orom *isci_get_efi_var(struct pci_dev *pdev); + +struct isci_oem_hdr { + u8 sig[4]; + u8 rev_major; + u8 rev_minor; + u16 len; + u8 checksum; + u8 reserved1; + u16 reserved2; +} __attribute__ ((packed)); + +#else +#define SCI_MAX_PORTS 4 +#define SCI_MAX_PHYS 4 +#define SCI_MAX_CONTROLLERS 2 +#endif + +#define ISCI_FW_NAME "isci/isci_firmware.bin" + +#define ROMSIGNATURE 0xaa55 + +#define ISCI_OEM_SIG "$OEM" +#define ISCI_OEM_SIG_SIZE 4 +#define ISCI_ROM_SIG "ISCUOEMB" +#define ISCI_ROM_SIG_SIZE 8 + +#define ISCI_EFI_VENDOR_GUID \ + EFI_GUID(0x193dfefa, 0xa445, 0x4302, 0x99, 0xd8, 0xef, 0x3a, 0xad, \ + 0x1a, 0x04, 0xc6) +#define ISCI_EFI_VAR_NAME "RstScuO" + +/* Allowed PORT configuration modes APC Automatic PORT configuration mode is + * defined by the OEM configuration parameters providing no PHY_MASK parameters + * for any PORT. i.e. There are no phys assigned to any of the ports at start. + * MPC Manual PORT configuration mode is defined by the OEM configuration + * parameters providing a PHY_MASK value for any PORT. It is assumed that any + * PORT with no PHY_MASK is an invalid port and not all PHYs must be assigned. + * A PORT_PHY mask that assigns just a single PHY to a port and no other PHYs + * being assigned is sufficient to declare manual PORT configuration. + */ +enum sci_port_configuration_mode { + SCIC_PORT_MANUAL_CONFIGURATION_MODE = 0, + SCIC_PORT_AUTOMATIC_CONFIGURATION_MODE = 1 +}; + +struct sci_bios_oem_param_block_hdr { + uint8_t signature[ISCI_ROM_SIG_SIZE]; + uint16_t total_block_length; + uint8_t hdr_length; + uint8_t version; + uint8_t preboot_source; + uint8_t num_elements; + uint16_t element_length; + uint8_t reserved[8]; +} __attribute__ ((packed)); + +struct sci_oem_params { + struct { + uint8_t mode_type; + uint8_t max_concurrent_dev_spin_up; + uint8_t do_enable_ssc; + uint8_t reserved; + } controller; + + struct { + uint8_t phy_mask; + } ports[SCI_MAX_PORTS]; + + struct sci_phy_oem_params { + struct { + uint32_t high; + uint32_t low; + } sas_address; + + uint32_t afe_tx_amp_control0; + uint32_t afe_tx_amp_control1; + uint32_t afe_tx_amp_control2; + uint32_t afe_tx_amp_control3; + } phys[SCI_MAX_PHYS]; +} __attribute__ ((packed)); + +struct isci_orom { + struct sci_bios_oem_param_block_hdr hdr; + struct sci_oem_params ctrl[SCI_MAX_CONTROLLERS]; +} __attribute__ ((packed)); + +#endif |