diff options
Diffstat (limited to 'drivers/scsi/lpfc/lpfc_init.c')
| -rw-r--r-- | drivers/scsi/lpfc/lpfc_init.c | 41 |
1 files changed, 28 insertions, 13 deletions
diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c index 35665cfb568..e6ebe516cfb 100644 --- a/drivers/scsi/lpfc/lpfc_init.c +++ b/drivers/scsi/lpfc/lpfc_init.c @@ -1,7 +1,7 @@ /******************************************************************* * This file is part of the Emulex Linux Device Driver for * * Fibre Channel Host Bus Adapters. * - * Copyright (C) 2004-2010 Emulex. All rights reserved. * + * Copyright (C) 2004-2011 Emulex. All rights reserved. * * EMULEX and SLI are trademarks of Emulex. * * www.emulex.com * * Portions Copyright (C) 2004-2005 Christoph Hellwig * @@ -507,7 +507,10 @@ lpfc_config_port_post(struct lpfc_hba *phba) phba->hba_flag &= ~HBA_ERATT_HANDLED; /* Enable appropriate host interrupts */ - status = readl(phba->HCregaddr); + if (lpfc_readl(phba->HCregaddr, &status)) { + spin_unlock_irq(&phba->hbalock); + return -EIO; + } status |= HC_MBINT_ENA | HC_ERINT_ENA | HC_LAINT_ENA; if (psli->num_rings > 0) status |= HC_R0INT_ENA; @@ -1222,7 +1225,10 @@ lpfc_handle_deferred_eratt(struct lpfc_hba *phba) /* Wait for the ER1 bit to clear.*/ while (phba->work_hs & HS_FFER1) { msleep(100); - phba->work_hs = readl(phba->HSregaddr); + if (lpfc_readl(phba->HSregaddr, &phba->work_hs)) { + phba->work_hs = UNPLUG_ERR ; + break; + } /* If driver is unloading let the worker thread continue */ if (phba->pport->load_flag & FC_UNLOADING) { phba->work_hs = 0; @@ -4474,6 +4480,7 @@ lpfc_init_api_table_setup(struct lpfc_hba *phba, uint8_t dev_grp) { phba->lpfc_hba_init_link = lpfc_hba_init_link; phba->lpfc_hba_down_link = lpfc_hba_down_link; + phba->lpfc_selective_reset = lpfc_selective_reset; switch (dev_grp) { case LPFC_PCI_DEV_LP: phba->lpfc_hba_down_post = lpfc_hba_down_post_s3; @@ -5385,13 +5392,16 @@ lpfc_sli4_post_status_check(struct lpfc_hba *phba) int i, port_error = 0; uint32_t if_type; + memset(&portsmphr_reg, 0, sizeof(portsmphr_reg)); + memset(®_data, 0, sizeof(reg_data)); if (!phba->sli4_hba.PSMPHRregaddr) return -ENODEV; /* Wait up to 30 seconds for the SLI Port POST done and ready */ for (i = 0; i < 3000; i++) { - portsmphr_reg.word0 = readl(phba->sli4_hba.PSMPHRregaddr); - if (bf_get(lpfc_port_smphr_perr, &portsmphr_reg)) { + if (lpfc_readl(phba->sli4_hba.PSMPHRregaddr, + &portsmphr_reg.word0) || + (bf_get(lpfc_port_smphr_perr, &portsmphr_reg))) { /* Port has a fatal POST error, break out */ port_error = -ENODEV; break; @@ -5472,9 +5482,9 @@ lpfc_sli4_post_status_check(struct lpfc_hba *phba) break; case LPFC_SLI_INTF_IF_TYPE_2: /* Final checks. The port status should be clean. */ - reg_data.word0 = - readl(phba->sli4_hba.u.if_type2.STATUSregaddr); - if (bf_get(lpfc_sliport_status_err, ®_data)) { + if (lpfc_readl(phba->sli4_hba.u.if_type2.STATUSregaddr, + ®_data.word0) || + bf_get(lpfc_sliport_status_err, ®_data)) { phba->work_status[0] = readl(phba->sli4_hba.u.if_type2. ERR1regaddr); @@ -6760,9 +6770,11 @@ lpfc_pci_function_reset(struct lpfc_hba *phba) * the loop again. */ for (rdy_chk = 0; rdy_chk < 1000; rdy_chk++) { - reg_data.word0 = - readl(phba->sli4_hba.u.if_type2. - STATUSregaddr); + if (lpfc_readl(phba->sli4_hba.u.if_type2. + STATUSregaddr, ®_data.word0)) { + rc = -ENODEV; + break; + } if (bf_get(lpfc_sliport_status_rdy, ®_data)) break; if (bf_get(lpfc_sliport_status_rn, ®_data)) { @@ -6783,8 +6795,11 @@ lpfc_pci_function_reset(struct lpfc_hba *phba) } /* Detect any port errors. */ - reg_data.word0 = readl(phba->sli4_hba.u.if_type2. - STATUSregaddr); + if (lpfc_readl(phba->sli4_hba.u.if_type2.STATUSregaddr, + ®_data.word0)) { + rc = -ENODEV; + break; + } if ((bf_get(lpfc_sliport_status_err, ®_data)) || (rdy_chk >= 1000)) { phba->work_status[0] = readl( |