summaryrefslogtreecommitdiffstats
path: root/drivers/tty/serial/sunsu.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/sunsu.c')
-rw-r--r--drivers/tty/serial/sunsu.c1608
1 files changed, 1608 insertions, 0 deletions
diff --git a/drivers/tty/serial/sunsu.c b/drivers/tty/serial/sunsu.c
new file mode 100644
index 00000000000..551ebfe3ccb
--- /dev/null
+++ b/drivers/tty/serial/sunsu.c
@@ -0,0 +1,1608 @@
+/*
+ * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI
+ *
+ * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be)
+ * Copyright (C) 1998-1999 Pete Zaitcev (zaitcev@yahoo.com)
+ *
+ * This is mainly a variation of 8250.c, credits go to authors mentioned
+ * therein. In fact this driver should be merged into the generic 8250.c
+ * infrastructure perhaps using a 8250_sparc.c module.
+ *
+ * Fixed to use tty_get_baud_rate().
+ * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12
+ *
+ * Converted to new 2.5.x UART layer.
+ * David S. Miller (davem@davemloft.net), 2002-Jul-29
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/errno.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/major.h>
+#include <linux/string.h>
+#include <linux/ptrace.h>
+#include <linux/ioport.h>
+#include <linux/circ_buf.h>
+#include <linux/serial.h>
+#include <linux/sysrq.h>
+#include <linux/console.h>
+#include <linux/slab.h>
+#ifdef CONFIG_SERIO
+#include <linux/serio.h>
+#endif
+#include <linux/serial_reg.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/of_device.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/prom.h>
+
+#if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/serial_core.h>
+
+#include "suncore.h"
+
+/* We are on a NS PC87303 clocked with 24.0 MHz, which results
+ * in a UART clock of 1.8462 MHz.
+ */
+#define SU_BASE_BAUD (1846200 / 16)
+
+enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT };
+static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" };
+
+/*
+ * Here we define the default xmit fifo size used for each type of UART.
+ */
+static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
+ { "unknown", 1, 0 },
+ { "8250", 1, 0 },
+ { "16450", 1, 0 },
+ { "16550", 1, 0 },
+ { "16550A", 16, UART_CLEAR_FIFO | UART_USE_FIFO },
+ { "Cirrus", 1, 0 },
+ { "ST16650", 1, UART_CLEAR_FIFO | UART_STARTECH },
+ { "ST16650V2", 32, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
+ { "TI16750", 64, UART_CLEAR_FIFO | UART_USE_FIFO },
+ { "Startech", 1, 0 },
+ { "16C950/954", 128, UART_CLEAR_FIFO | UART_USE_FIFO },
+ { "ST16654", 64, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
+ { "XR16850", 128, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
+ { "RSA", 2048, UART_CLEAR_FIFO | UART_USE_FIFO }
+};
+
+struct uart_sunsu_port {
+ struct uart_port port;
+ unsigned char acr;
+ unsigned char ier;
+ unsigned short rev;
+ unsigned char lcr;
+ unsigned int lsr_break_flag;
+ unsigned int cflag;
+
+ /* Probing information. */
+ enum su_type su_type;
+ unsigned int type_probed; /* XXX Stupid */
+ unsigned long reg_size;
+
+#ifdef CONFIG_SERIO
+ struct serio serio;
+ int serio_open;
+#endif
+};
+
+static unsigned int serial_in(struct uart_sunsu_port *up, int offset)
+{
+ offset <<= up->port.regshift;
+
+ switch (up->port.iotype) {
+ case UPIO_HUB6:
+ outb(up->port.hub6 - 1 + offset, up->port.iobase);
+ return inb(up->port.iobase + 1);
+
+ case UPIO_MEM:
+ return readb(up->port.membase + offset);
+
+ default:
+ return inb(up->port.iobase + offset);
+ }
+}
+
+static void serial_out(struct uart_sunsu_port *up, int offset, int value)
+{
+#ifndef CONFIG_SPARC64
+ /*
+ * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are
+ * connected with a gate then go to SlavIO. When IRQ4 goes tristated
+ * gate outputs a logical one. Since we use level triggered interrupts
+ * we have lockup and watchdog reset. We cannot mask IRQ because
+ * keyboard shares IRQ with us (Word has it as Bob Smelik's design).
+ * This problem is similar to what Alpha people suffer, see serial.c.
+ */
+ if (offset == UART_MCR)
+ value |= UART_MCR_OUT2;
+#endif
+ offset <<= up->port.regshift;
+
+ switch (up->port.iotype) {
+ case UPIO_HUB6:
+ outb(up->port.hub6 - 1 + offset, up->port.iobase);
+ outb(value, up->port.iobase + 1);
+ break;
+
+ case UPIO_MEM:
+ writeb(value, up->port.membase + offset);
+ break;
+
+ default:
+ outb(value, up->port.iobase + offset);
+ }
+}
+
+/*
+ * We used to support using pause I/O for certain machines. We
+ * haven't supported this for a while, but just in case it's badly
+ * needed for certain old 386 machines, I've left these #define's
+ * in....
+ */
+#define serial_inp(up, offset) serial_in(up, offset)
+#define serial_outp(up, offset, value) serial_out(up, offset, value)
+
+
+/*
+ * For the 16C950
+ */
+static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value)
+{
+ serial_out(up, UART_SCR, offset);
+ serial_out(up, UART_ICR, value);
+}
+
+#if 0 /* Unused currently */
+static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset)
+{
+ unsigned int value;
+
+ serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
+ serial_out(up, UART_SCR, offset);
+ value = serial_in(up, UART_ICR);
+ serial_icr_write(up, UART_ACR, up->acr);
+
+ return value;
+}
+#endif
+
+#ifdef CONFIG_SERIAL_8250_RSA
+/*
+ * Attempts to turn on the RSA FIFO. Returns zero on failure.
+ * We set the port uart clock rate if we succeed.
+ */
+static int __enable_rsa(struct uart_sunsu_port *up)
+{
+ unsigned char mode;
+ int result;
+
+ mode = serial_inp(up, UART_RSA_MSR);
+ result = mode & UART_RSA_MSR_FIFO;
+
+ if (!result) {
+ serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
+ mode = serial_inp(up, UART_RSA_MSR);
+ result = mode & UART_RSA_MSR_FIFO;
+ }
+
+ if (result)
+ up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
+
+ return result;
+}
+
+static void enable_rsa(struct uart_sunsu_port *up)
+{
+ if (up->port.type == PORT_RSA) {
+ if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
+ spin_lock_irq(&up->port.lock);
+ __enable_rsa(up);
+ spin_unlock_irq(&up->port.lock);
+ }
+ if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
+ serial_outp(up, UART_RSA_FRR, 0);
+ }
+}
+
+/*
+ * Attempts to turn off the RSA FIFO. Returns zero on failure.
+ * It is unknown why interrupts were disabled in here. However,
+ * the caller is expected to preserve this behaviour by grabbing
+ * the spinlock before calling this function.
+ */
+static void disable_rsa(struct uart_sunsu_port *up)
+{
+ unsigned char mode;
+ int result;
+
+ if (up->port.type == PORT_RSA &&
+ up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
+ spin_lock_irq(&up->port.lock);
+
+ mode = serial_inp(up, UART_RSA_MSR);
+ result = !(mode & UART_RSA_MSR_FIFO);
+
+ if (!result) {
+ serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
+ mode = serial_inp(up, UART_RSA_MSR);
+ result = !(mode & UART_RSA_MSR_FIFO);
+ }
+
+ if (result)
+ up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
+ spin_unlock_irq(&up->port.lock);
+ }
+}
+#endif /* CONFIG_SERIAL_8250_RSA */
+
+static inline void __stop_tx(struct uart_sunsu_port *p)
+{
+ if (p->ier & UART_IER_THRI) {
+ p->ier &= ~UART_IER_THRI;
+ serial_out(p, UART_IER, p->ier);
+ }
+}
+
+static void sunsu_stop_tx(struct uart_port *port)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+
+ __stop_tx(up);
+
+ /*
+ * We really want to stop the transmitter from sending.
+ */
+ if (up->port.type == PORT_16C950) {
+ up->acr |= UART_ACR_TXDIS;
+ serial_icr_write(up, UART_ACR, up->acr);
+ }
+}
+
+static void sunsu_start_tx(struct uart_port *port)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+
+ if (!(up->ier & UART_IER_THRI)) {
+ up->ier |= UART_IER_THRI;
+ serial_out(up, UART_IER, up->ier);
+ }
+
+ /*
+ * Re-enable the transmitter if we disabled it.
+ */
+ if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
+ up->acr &= ~UART_ACR_TXDIS;
+ serial_icr_write(up, UART_ACR, up->acr);
+ }
+}
+
+static void sunsu_stop_rx(struct uart_port *port)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+
+ up->ier &= ~UART_IER_RLSI;
+ up->port.read_status_mask &= ~UART_LSR_DR;
+ serial_out(up, UART_IER, up->ier);
+}
+
+static void sunsu_enable_ms(struct uart_port *port)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ up->ier |= UART_IER_MSI;
+ serial_out(up, UART_IER, up->ier);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static struct tty_struct *
+receive_chars(struct uart_sunsu_port *up, unsigned char *status)
+{
+ struct tty_struct *tty = up->port.state->port.tty;
+ unsigned char ch, flag;
+ int max_count = 256;
+ int saw_console_brk = 0;
+
+ do {
+ ch = serial_inp(up, UART_RX);
+ flag = TTY_NORMAL;
+ up->port.icount.rx++;
+
+ if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
+ UART_LSR_FE | UART_LSR_OE))) {
+ /*
+ * For statistics only
+ */
+ if (*status & UART_LSR_BI) {
+ *status &= ~(UART_LSR_FE | UART_LSR_PE);
+ up->port.icount.brk++;
+ if (up->port.cons != NULL &&
+ up->port.line == up->port.cons->index)
+ saw_console_brk = 1;
+ /*
+ * We do the SysRQ and SAK checking
+ * here because otherwise the break
+ * may get masked by ignore_status_mask
+ * or read_status_mask.
+ */
+ if (uart_handle_break(&up->port))
+ goto ignore_char;
+ } else if (*status & UART_LSR_PE)
+ up->port.icount.parity++;
+ else if (*status & UART_LSR_FE)
+ up->port.icount.frame++;
+ if (*status & UART_LSR_OE)
+ up->port.icount.overrun++;
+
+ /*
+ * Mask off conditions which should be ingored.
+ */
+ *status &= up->port.read_status_mask;
+
+ if (up->port.cons != NULL &&
+ up->port.line == up->port.cons->index) {
+ /* Recover the break flag from console xmit */
+ *status |= up->lsr_break_flag;
+ up->lsr_break_flag = 0;
+ }
+
+ if (*status & UART_LSR_BI) {
+ flag = TTY_BREAK;
+ } else if (*status & UART_LSR_PE)
+ flag = TTY_PARITY;
+ else if (*status & UART_LSR_FE)
+ flag = TTY_FRAME;
+ }
+ if (uart_handle_sysrq_char(&up->port, ch))
+ goto ignore_char;
+ if ((*status & up->port.ignore_status_mask) == 0)
+ tty_insert_flip_char(tty, ch, flag);
+ if (*status & UART_LSR_OE)
+ /*
+ * Overrun is special, since it's reported
+ * immediately, and doesn't affect the current
+ * character.
+ */
+ tty_insert_flip_char(tty, 0, TTY_OVERRUN);
+ ignore_char:
+ *status = serial_inp(up, UART_LSR);
+ } while ((*status & UART_LSR_DR) && (max_count-- > 0));
+
+ if (saw_console_brk)
+ sun_do_break();
+
+ return tty;
+}
+
+static void transmit_chars(struct uart_sunsu_port *up)
+{
+ struct circ_buf *xmit = &up->port.state->xmit;
+ int count;
+
+ if (up->port.x_char) {
+ serial_outp(up, UART_TX, up->port.x_char);
+ up->port.icount.tx++;
+ up->port.x_char = 0;
+ return;
+ }
+ if (uart_tx_stopped(&up->port)) {
+ sunsu_stop_tx(&up->port);
+ return;
+ }
+ if (uart_circ_empty(xmit)) {
+ __stop_tx(up);
+ return;
+ }
+
+ count = up->port.fifosize;
+ do {
+ serial_out(up, UART_TX, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ up->port.icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ } while (--count > 0);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&up->port);
+
+ if (uart_circ_empty(xmit))
+ __stop_tx(up);
+}
+
+static void check_modem_status(struct uart_sunsu_port *up)
+{
+ int status;
+
+ status = serial_in(up, UART_MSR);
+
+ if ((status & UART_MSR_ANY_DELTA) == 0)
+ return;
+
+ if (status & UART_MSR_TERI)
+ up->port.icount.rng++;
+ if (status & UART_MSR_DDSR)
+ up->port.icount.dsr++;
+ if (status & UART_MSR_DDCD)
+ uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
+ if (status & UART_MSR_DCTS)
+ uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
+
+ wake_up_interruptible(&up->port.state->port.delta_msr_wait);
+}
+
+static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id)
+{
+ struct uart_sunsu_port *up = dev_id;
+ unsigned long flags;
+ unsigned char status;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+
+ do {
+ struct tty_struct *tty;
+
+ status = serial_inp(up, UART_LSR);
+ tty = NULL;
+ if (status & UART_LSR_DR)
+ tty = receive_chars(up, &status);
+ check_modem_status(up);
+ if (status & UART_LSR_THRE)
+ transmit_chars(up);
+
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ if (tty)
+ tty_flip_buffer_push(tty);
+
+ spin_lock_irqsave(&up->port.lock, flags);
+
+ } while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT));
+
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+/* Separate interrupt handling path for keyboard/mouse ports. */
+
+static void
+sunsu_change_speed(struct uart_port *port, unsigned int cflag,
+ unsigned int iflag, unsigned int quot);
+
+static void sunsu_change_mouse_baud(struct uart_sunsu_port *up)
+{
+ unsigned int cur_cflag = up->cflag;
+ int quot, new_baud;
+
+ up->cflag &= ~CBAUD;
+ up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
+
+ quot = up->port.uartclk / (16 * new_baud);
+
+ sunsu_change_speed(&up->port, up->cflag, 0, quot);
+}
+
+static void receive_kbd_ms_chars(struct uart_sunsu_port *up, int is_break)
+{
+ do {
+ unsigned char ch = serial_inp(up, UART_RX);
+
+ /* Stop-A is handled by drivers/char/keyboard.c now. */
+ if (up->su_type == SU_PORT_KBD) {
+#ifdef CONFIG_SERIO
+ serio_interrupt(&up->serio, ch, 0);
+#endif
+ } else if (up->su_type == SU_PORT_MS) {
+ int ret = suncore_mouse_baud_detection(ch, is_break);
+
+ switch (ret) {
+ case 2:
+ sunsu_change_mouse_baud(up);
+ /* fallthru */
+ case 1:
+ break;
+
+ case 0:
+#ifdef CONFIG_SERIO
+ serio_interrupt(&up->serio, ch, 0);
+#endif
+ break;
+ };
+ }
+ } while (serial_in(up, UART_LSR) & UART_LSR_DR);
+}
+
+static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id)
+{
+ struct uart_sunsu_port *up = dev_id;
+
+ if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) {
+ unsigned char status = serial_inp(up, UART_LSR);
+
+ if ((status & UART_LSR_DR) || (status & UART_LSR_BI))
+ receive_kbd_ms_chars(up, (status & UART_LSR_BI) != 0);
+ }
+
+ return IRQ_HANDLED;
+}
+
+static unsigned int sunsu_tx_empty(struct uart_port *port)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+ unsigned long flags;
+ unsigned int ret;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ return ret;
+}
+
+static unsigned int sunsu_get_mctrl(struct uart_port *port)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+ unsigned char status;
+ unsigned int ret;
+
+ status = serial_in(up, UART_MSR);
+
+ ret = 0;
+ if (status & UART_MSR_DCD)
+ ret |= TIOCM_CAR;
+ if (status & UART_MSR_RI)
+ ret |= TIOCM_RNG;
+ if (status & UART_MSR_DSR)
+ ret |= TIOCM_DSR;
+ if (status & UART_MSR_CTS)
+ ret |= TIOCM_CTS;
+ return ret;
+}
+
+static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+ unsigned char mcr = 0;
+
+ if (mctrl & TIOCM_RTS)
+ mcr |= UART_MCR_RTS;
+ if (mctrl & TIOCM_DTR)
+ mcr |= UART_MCR_DTR;
+ if (mctrl & TIOCM_OUT1)
+ mcr |= UART_MCR_OUT1;
+ if (mctrl & TIOCM_OUT2)
+ mcr |= UART_MCR_OUT2;
+ if (mctrl & TIOCM_LOOP)
+ mcr |= UART_MCR_LOOP;
+
+ serial_out(up, UART_MCR, mcr);
+}
+
+static void sunsu_break_ctl(struct uart_port *port, int break_state)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+ unsigned long flags;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ if (break_state == -1)
+ up->lcr |= UART_LCR_SBC;
+ else
+ up->lcr &= ~UART_LCR_SBC;
+ serial_out(up, UART_LCR, up->lcr);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static int sunsu_startup(struct uart_port *port)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+ unsigned long flags;
+ int retval;
+
+ if (up->port.type == PORT_16C950) {
+ /* Wake up and initialize UART */
+ up->acr = 0;
+ serial_outp(up, UART_LCR, 0xBF);
+ serial_outp(up, UART_EFR, UART_EFR_ECB);
+ serial_outp(up, UART_IER, 0);
+ serial_outp(up, UART_LCR, 0);
+ serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
+ serial_outp(up, UART_LCR, 0xBF);
+ serial_outp(up, UART_EFR, UART_EFR_ECB);
+ serial_outp(up, UART_LCR, 0);
+ }
+
+#ifdef CONFIG_SERIAL_8250_RSA
+ /*
+ * If this is an RSA port, see if we can kick it up to the
+ * higher speed clock.
+ */
+ enable_rsa(up);
+#endif
+
+ /*
+ * Clear the FIFO buffers and disable them.
+ * (they will be reenabled in set_termios())
+ */
+ if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
+ serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+ UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
+ serial_outp(up, UART_FCR, 0);
+ }
+
+ /*
+ * Clear the interrupt registers.
+ */
+ (void) serial_inp(up, UART_LSR);
+ (void) serial_inp(up, UART_RX);
+ (void) serial_inp(up, UART_IIR);
+ (void) serial_inp(up, UART_MSR);
+
+ /*
+ * At this point, there's no way the LSR could still be 0xff;
+ * if it is, then bail out, because there's likely no UART
+ * here.
+ */
+ if (!(up->port.flags & UPF_BUGGY_UART) &&
+ (serial_inp(up, UART_LSR) == 0xff)) {
+ printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
+ return -ENODEV;
+ }
+
+ if (up->su_type != SU_PORT_PORT) {
+ retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt,
+ IRQF_SHARED, su_typev[up->su_type], up);
+ } else {
+ retval = request_irq(up->port.irq, sunsu_serial_interrupt,
+ IRQF_SHARED, su_typev[up->su_type], up);
+ }
+ if (retval) {
+ printk("su: Cannot register IRQ %d\n", up->port.irq);
+ return retval;
+ }
+
+ /*
+ * Now, initialize the UART
+ */
+ serial_outp(up, UART_LCR, UART_LCR_WLEN8);
+
+ spin_lock_irqsave(&up->port.lock, flags);
+
+ up->port.mctrl |= TIOCM_OUT2;
+
+ sunsu_set_mctrl(&up->port, up->port.mctrl);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ /*
+ * Finally, enable interrupts. Note: Modem status interrupts
+ * are set via set_termios(), which will be occurring imminently
+ * anyway, so we don't enable them here.
+ */
+ up->ier = UART_IER_RLSI | UART_IER_RDI;
+ serial_outp(up, UART_IER, up->ier);
+
+ if (up->port.flags & UPF_FOURPORT) {
+ unsigned int icp;
+ /*
+ * Enable interrupts on the AST Fourport board
+ */
+ icp = (up->port.iobase & 0xfe0) | 0x01f;
+ outb_p(0x80, icp);
+ (void) inb_p(icp);
+ }
+
+ /*
+ * And clear the interrupt registers again for luck.
+ */
+ (void) serial_inp(up, UART_LSR);
+ (void) serial_inp(up, UART_RX);
+ (void) serial_inp(up, UART_IIR);
+ (void) serial_inp(up, UART_MSR);
+
+ return 0;
+}
+
+static void sunsu_shutdown(struct uart_port *port)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+ unsigned long flags;
+
+ /*
+ * Disable interrupts from this port
+ */
+ up->ier = 0;
+ serial_outp(up, UART_IER, 0);
+
+ spin_lock_irqsave(&up->port.lock, flags);
+ if (up->port.flags & UPF_FOURPORT) {
+ /* reset interrupts on the AST Fourport board */
+ inb((up->port.iobase & 0xfe0) | 0x1f);
+ up->port.mctrl |= TIOCM_OUT1;
+ } else
+ up->port.mctrl &= ~TIOCM_OUT2;
+
+ sunsu_set_mctrl(&up->port, up->port.mctrl);
+ spin_unlock_irqrestore(&up->port.lock, flags);
+
+ /*
+ * Disable break condition and FIFOs
+ */
+ serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
+ serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+ UART_FCR_CLEAR_RCVR |
+ UART_FCR_CLEAR_XMIT);
+ serial_outp(up, UART_FCR, 0);
+
+#ifdef CONFIG_SERIAL_8250_RSA
+ /*
+ * Reset the RSA board back to 115kbps compat mode.
+ */
+ disable_rsa(up);
+#endif
+
+ /*
+ * Read data port to reset things.
+ */
+ (void) serial_in(up, UART_RX);
+
+ free_irq(up->port.irq, up);
+}
+
+static void
+sunsu_change_speed(struct uart_port *port, unsigned int cflag,
+ unsigned int iflag, unsigned int quot)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+ unsigned char cval, fcr = 0;
+ unsigned long flags;
+
+ switch (cflag & CSIZE) {
+ case CS5:
+ cval = 0x00;
+ break;
+ case CS6:
+ cval = 0x01;
+ break;
+ case CS7:
+ cval = 0x02;
+ break;
+ default:
+ case CS8:
+ cval = 0x03;
+ break;
+ }
+
+ if (cflag & CSTOPB)
+ cval |= 0x04;
+ if (cflag & PARENB)
+ cval |= UART_LCR_PARITY;
+ if (!(cflag & PARODD))
+ cval |= UART_LCR_EPAR;
+#ifdef CMSPAR
+ if (cflag & CMSPAR)
+ cval |= UART_LCR_SPAR;
+#endif
+
+ /*
+ * Work around a bug in the Oxford Semiconductor 952 rev B
+ * chip which causes it to seriously miscalculate baud rates
+ * when DLL is 0.
+ */
+ if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
+ up->rev == 0x5201)
+ quot ++;
+
+ if (uart_config[up->port.type].flags & UART_USE_FIFO) {
+ if ((up->port.uartclk / quot) < (2400 * 16))
+ fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
+#ifdef CONFIG_SERIAL_8250_RSA
+ else if (up->port.type == PORT_RSA)
+ fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14;
+#endif
+ else
+ fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8;
+ }
+ if (up->port.type == PORT_16750)
+ fcr |= UART_FCR7_64BYTE;
+
+ /*
+ * Ok, we're now changing the port state. Do it with
+ * interrupts disabled.
+ */
+ spin_lock_irqsave(&up->port.lock, flags);
+
+ /*
+ * Update the per-port timeout.
+ */
+ uart_update_timeout(port, cflag, (port->uartclk / (16 * quot)));
+
+ up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
+ if (iflag & INPCK)
+ up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
+ if (iflag & (BRKINT | PARMRK))
+ up->port.read_status_mask |= UART_LSR_BI;
+
+ /*
+ * Characteres to ignore
+ */
+ up->port.ignore_status_mask = 0;
+ if (iflag & IGNPAR)
+ up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
+ if (iflag & IGNBRK) {
+ up->port.ignore_status_mask |= UART_LSR_BI;
+ /*
+ * If we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (iflag & IGNPAR)
+ up->port.ignore_status_mask |= UART_LSR_OE;
+ }
+
+ /*
+ * ignore all characters if CREAD is not set
+ */
+ if ((cflag & CREAD) == 0)
+ up->port.ignore_status_mask |= UART_LSR_DR;
+
+ /*
+ * CTS flow control flag and modem status interrupts
+ */
+ up->ier &= ~UART_IER_MSI;
+ if (UART_ENABLE_MS(&up->port, cflag))
+ up->ier |= UART_IER_MSI;
+
+ serial_out(up, UART_IER, up->ier);
+
+ if (uart_config[up->port.type].flags & UART_STARTECH) {
+ serial_outp(up, UART_LCR, 0xBF);
+ serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0);
+ }
+ serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
+ serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */
+ serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */
+ if (up->port.type == PORT_16750)
+ serial_outp(up, UART_FCR, fcr); /* set fcr */
+ serial_outp(up, UART_LCR, cval); /* reset DLAB */
+ up->lcr = cval; /* Save LCR */
+ if (up->port.type != PORT_16750) {
+ if (fcr & UART_FCR_ENABLE_FIFO) {
+ /* emulated UARTs (Lucent Venus 167x) need two steps */
+ serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ }
+ serial_outp(up, UART_FCR, fcr); /* set fcr */
+ }
+
+ up->cflag = cflag;
+
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static void
+sunsu_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ unsigned int baud, quot;
+
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+ quot = uart_get_divisor(port, baud);
+
+ sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot);
+}
+
+static void sunsu_release_port(struct uart_port *port)
+{
+}
+
+static int sunsu_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+static void sunsu_config_port(struct uart_port *port, int flags)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
+
+ if (flags & UART_CONFIG_TYPE) {
+ /*
+ * We are supposed to call autoconfig here, but this requires
+ * splitting all the OBP probing crap from the UART probing.
+ * We'll do it when we kill sunsu.c altogether.
+ */
+ port->type = up->type_probed; /* XXX */
+ }
+}
+
+static int
+sunsu_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ return -EINVAL;
+}
+
+static const char *
+sunsu_type(struct uart_port *port)
+{
+ int type = port->type;
+
+ if (type >= ARRAY_SIZE(uart_config))
+ type = 0;
+ return uart_config[type].name;
+}
+
+static struct uart_ops sunsu_pops = {
+ .tx_empty = sunsu_tx_empty,
+ .set_mctrl = sunsu_set_mctrl,
+ .get_mctrl = sunsu_get_mctrl,
+ .stop_tx = sunsu_stop_tx,
+ .start_tx = sunsu_start_tx,
+ .stop_rx = sunsu_stop_rx,
+ .enable_ms = sunsu_enable_ms,
+ .break_ctl = sunsu_break_ctl,
+ .startup = sunsu_startup,
+ .shutdown = sunsu_shutdown,
+ .set_termios = sunsu_set_termios,
+ .type = sunsu_type,
+ .release_port = sunsu_release_port,
+ .request_port = sunsu_request_port,
+ .config_port = sunsu_config_port,
+ .verify_port = sunsu_verify_port,
+};
+
+#define UART_NR 4
+
+static struct uart_sunsu_port sunsu_ports[UART_NR];
+
+#ifdef CONFIG_SERIO
+
+static DEFINE_SPINLOCK(sunsu_serio_lock);
+
+static int sunsu_serio_write(struct serio *serio, unsigned char ch)
+{
+ struct uart_sunsu_port *up = serio->port_data;
+ unsigned long flags;
+ int lsr;
+
+ spin_lock_irqsave(&sunsu_serio_lock, flags);
+
+ do {
+ lsr = serial_in(up, UART_LSR);
+ } while (!(lsr & UART_LSR_THRE));
+
+ /* Send the character out. */
+ serial_out(up, UART_TX, ch);
+
+ spin_unlock_irqrestore(&sunsu_serio_lock, flags);
+
+ return 0;
+}
+
+static int sunsu_serio_open(struct serio *serio)
+{
+ struct uart_sunsu_port *up = serio->port_data;
+ unsigned long flags;
+ int ret;
+
+ spin_lock_irqsave(&sunsu_serio_lock, flags);
+ if (!up->serio_open) {
+ up->serio_open = 1;
+ ret = 0;
+ } else
+ ret = -EBUSY;
+ spin_unlock_irqrestore(&sunsu_serio_lock, flags);
+
+ return ret;
+}
+
+static void sunsu_serio_close(struct serio *serio)
+{
+ struct uart_sunsu_port *up = serio->port_data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&sunsu_serio_lock, flags);
+ up->serio_open = 0;
+ spin_unlock_irqrestore(&sunsu_serio_lock, flags);
+}
+
+#endif /* CONFIG_SERIO */
+
+static void sunsu_autoconfig(struct uart_sunsu_port *up)
+{
+ unsigned char status1, status2, scratch, scratch2, scratch3;
+ unsigned char save_lcr, save_mcr;
+ unsigned long flags;
+
+ if (up->su_type == SU_PORT_NONE)
+ return;
+
+ up->type_probed = PORT_UNKNOWN;
+ up->port.iotype = UPIO_MEM;
+
+ spin_lock_irqsave(&up->port.lock, flags);
+
+ if (!(up->port.flags & UPF_BUGGY_UART)) {
+ /*
+ * Do a simple existence test first; if we fail this, there's
+ * no point trying anything else.
+ *
+ * 0x80 is used as a nonsense port to prevent against false
+ * positives due to ISA bus float. The assumption is that
+ * 0x80 is a non-existent port; which should be safe since
+ * include/asm/io.h also makes this assumption.
+ */
+ scratch = serial_inp(up, UART_IER);
+ serial_outp(up, UART_IER, 0);
+#ifdef __i386__
+ outb(0xff, 0x080);
+#endif
+ scratch2 = serial_inp(up, UART_IER);
+ serial_outp(up, UART_IER, 0x0f);
+#ifdef __i386__
+ outb(0, 0x080);
+#endif
+ scratch3 = serial_inp(up, UART_IER);
+ serial_outp(up, UART_IER, scratch);
+ if (scratch2 != 0 || scratch3 != 0x0F)
+ goto out; /* We failed; there's nothing here */
+ }
+
+ save_mcr = serial_in(up, UART_MCR);
+ save_lcr = serial_in(up, UART_LCR);
+
+ /*
+ * Check to see if a UART is really there. Certain broken
+ * internal modems based on the Rockwell chipset fail this
+ * test, because they apparently don't implement the loopback
+ * test mode. So this test is skipped on the COM 1 through
+ * COM 4 ports. This *should* be safe, since no board
+ * manufacturer would be stupid enough to design a board
+ * that conflicts with COM 1-4 --- we hope!
+ */
+ if (!(up->port.flags & UPF_SKIP_TEST)) {
+ serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
+ status1 = serial_inp(up, UART_MSR) & 0xF0;
+ serial_outp(up, UART_MCR, save_mcr);
+ if (status1 != 0x90)
+ goto out; /* We failed loopback test */
+ }
+ serial_outp(up, UART_LCR, 0xBF); /* set up for StarTech test */
+ serial_outp(up, UART_EFR, 0); /* EFR is the same as FCR */
+ serial_outp(up, UART_LCR, 0);
+ serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ scratch = serial_in(up, UART_IIR) >> 6;
+ switch (scratch) {
+ case 0:
+ up->port.type = PORT_16450;
+ break;
+ case 1:
+ up->port.type = PORT_UNKNOWN;
+ break;
+ case 2:
+ up->port.type = PORT_16550;
+ break;
+ case 3:
+ up->port.type = PORT_16550A;
+ break;
+ }
+ if (up->port.type == PORT_16550A) {
+ /* Check for Startech UART's */
+ serial_outp(up, UART_LCR, UART_LCR_DLAB);
+ if (serial_in(up, UART_EFR) == 0) {
+ up->port.type = PORT_16650;
+ } else {
+ serial_outp(up, UART_LCR, 0xBF);
+ if (serial_in(up, UART_EFR) == 0)
+ up->port.type = PORT_16650V2;
+ }
+ }
+ if (up->port.type == PORT_16550A) {
+ /* Check for TI 16750 */
+ serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB);
+ serial_outp(up, UART_FCR,
+ UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
+ scratch = serial_in(up, UART_IIR) >> 5;
+ if (scratch == 7) {
+ /*
+ * If this is a 16750, and not a cheap UART
+ * clone, then it should only go into 64 byte
+ * mode if the UART_FCR7_64BYTE bit was set
+ * while UART_LCR_DLAB was latched.
+ */
+ serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ serial_outp(up, UART_LCR, 0);
+ serial_outp(up, UART_FCR,
+ UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
+ scratch = serial_in(up, UART_IIR) >> 5;
+ if (scratch == 6)
+ up->port.type = PORT_16750;
+ }
+ serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ }
+ serial_outp(up, UART_LCR, save_lcr);
+ if (up->port.type == PORT_16450) {
+ scratch = serial_in(up, UART_SCR);
+ serial_outp(up, UART_SCR, 0xa5);
+ status1 = serial_in(up, UART_SCR);
+ serial_outp(up, UART_SCR, 0x5a);
+ status2 = serial_in(up, UART_SCR);
+ serial_outp(up, UART_SCR, scratch);
+
+ if ((status1 != 0xa5) || (status2 != 0x5a))
+ up->port.type = PORT_8250;
+ }
+
+ up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
+
+ if (up->port.type == PORT_UNKNOWN)
+ goto out;
+ up->type_probed = up->port.type; /* XXX */
+
+ /*
+ * Reset the UART.
+ */
+#ifdef CONFIG_SERIAL_8250_RSA
+ if (up->port.type == PORT_RSA)
+ serial_outp(up, UART_RSA_FRR, 0);
+#endif
+ serial_outp(up, UART_MCR, save_mcr);
+ serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
+ UART_FCR_CLEAR_RCVR |
+ UART_FCR_CLEAR_XMIT));
+ serial_outp(up, UART_FCR, 0);
+ (void)serial_in(up, UART_RX);
+ serial_outp(up, UART_IER, 0);
+
+out:
+ spin_unlock_irqrestore(&up->port.lock, flags);
+}
+
+static struct uart_driver sunsu_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "sunsu",
+ .dev_name = "ttyS",
+ .major = TTY_MAJOR,
+};
+
+static int __devinit sunsu_kbd_ms_init(struct uart_sunsu_port *up)
+{
+ int quot, baud;
+#ifdef CONFIG_SERIO
+ struct serio *serio;
+#endif
+
+ if (up->su_type == SU_PORT_KBD) {
+ up->cflag = B1200 | CS8 | CLOCAL | CREAD;
+ baud = 1200;
+ } else {
+ up->cflag = B4800 | CS8 | CLOCAL | CREAD;
+ baud = 4800;
+ }
+ quot = up->port.uartclk / (16 * baud);
+
+ sunsu_autoconfig(up);
+ if (up->port.type == PORT_UNKNOWN)
+ return -ENODEV;
+
+ printk("%s: %s port at %llx, irq %u\n",
+ up->port.dev->of_node->full_name,
+ (up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse",
+ (unsigned long long) up->port.mapbase,
+ up->port.irq);
+
+#ifdef CONFIG_SERIO
+ serio = &up->serio;
+ serio->port_data = up;
+
+ serio->id.type = SERIO_RS232;
+ if (up->su_type == SU_PORT_KBD) {
+ serio->id.proto = SERIO_SUNKBD;
+ strlcpy(serio->name, "sukbd", sizeof(serio->name));
+ } else {
+ serio->id.proto = SERIO_SUN;
+ serio->id.extra = 1;
+ strlcpy(serio->name, "sums", sizeof(serio->name));
+ }
+ strlcpy(serio->phys,
+ (!(up->port.line & 1) ? "su/serio0" : "su/serio1"),
+ sizeof(serio->phys));
+
+ serio->write = sunsu_serio_write;
+ serio->open = sunsu_serio_open;
+ serio->close = sunsu_serio_close;
+ serio->dev.parent = up->port.dev;
+
+ serio_register_port(serio);
+#endif
+
+ sunsu_change_speed(&up->port, up->cflag, 0, quot);
+
+ sunsu_startup(&up->port);
+ return 0;
+}
+
+/*
+ * ------------------------------------------------------------
+ * Serial console driver
+ * ------------------------------------------------------------
+ */
+
+#ifdef CONFIG_SERIAL_SUNSU_CONSOLE
+
+#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
+
+/*
+ * Wait for transmitter & holding register to empty
+ */
+static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up)
+{
+ unsigned int status, tmout = 10000;
+
+ /* Wait up to 10ms for the character(s) to be sent. */
+ do {
+ status = serial_in(up, UART_LSR);
+
+ if (status & UART_LSR_BI)
+ up->lsr_break_flag = UART_LSR_BI;
+
+ if (--tmout == 0)
+ break;
+ udelay(1);
+ } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
+
+ /* Wait up to 1s for flow control if necessary */
+ if (up->port.flags & UPF_CONS_FLOW) {
+ tmout = 1000000;
+ while (--tmout &&
+ ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
+ udelay(1);
+ }
+}
+
+static void sunsu_console_putchar(struct uart_port *port, int ch)
+{
+ struct uart_sunsu_port *up = (struct uart_sunsu_port *)port;
+
+ wait_for_xmitr(up);
+ serial_out(up, UART_TX, ch);
+}
+
+/*
+ * Print a string to the serial port trying not to disturb
+ * any possible real use of the port...
+ */
+static void sunsu_console_write(struct console *co, const char *s,
+ unsigned int count)
+{
+ struct uart_sunsu_port *up = &sunsu_ports[co->index];
+ unsigned long flags;
+ unsigned int ier;
+ int locked = 1;
+
+ local_irq_save(flags);
+ if (up->port.sysrq) {
+ locked = 0;
+ } else if (oops_in_progress) {
+ locked = spin_trylock(&up->port.lock);
+ } else
+ spin_lock(&up->port.lock);
+
+ /*
+ * First save the UER then disable the interrupts
+ */
+ ier = serial_in(up, UART_IER);
+ serial_out(up, UART_IER, 0);
+
+ uart_console_write(&up->port, s, count, sunsu_console_putchar);
+
+ /*
+ * Finally, wait for transmitter to become empty
+ * and restore the IER
+ */
+ wait_for_xmitr(up);
+ serial_out(up, UART_IER, ier);
+
+ if (locked)
+ spin_unlock(&up->port.lock);
+ local_irq_restore(flags);
+}
+
+/*
+ * Setup initial baud/bits/parity. We do two things here:
+ * - construct a cflag setting for the first su_open()
+ * - initialize the serial port
+ * Return non-zero if we didn't find a serial port.
+ */
+static int __init sunsu_console_setup(struct console *co, char *options)
+{
+ static struct ktermios dummy;
+ struct ktermios termios;
+ struct uart_port *port;
+
+ printk("Console: ttyS%d (SU)\n",
+ (sunsu_reg.minor - 64) + co->index);
+
+ /*
+ * Check whether an invalid uart number has been specified, and
+ * if so, search for the first available port that does have
+ * console support.
+ */
+ if (co->index >= UART_NR)
+ co->index = 0;
+ port = &sunsu_ports[co->index].port;
+
+ /*
+ * Temporary fix.
+ */
+ spin_lock_init(&port->lock);
+
+ /* Get firmware console settings. */
+ sunserial_console_termios(co, port->dev->of_node);
+
+ memset(&termios, 0, sizeof(struct ktermios));
+ termios.c_cflag = co->cflag;
+ port->mctrl |= TIOCM_DTR;
+ port->ops->set_termios(port, &termios, &dummy);
+
+ return 0;
+}
+
+static struct console sunsu_console = {
+ .name = "ttyS",
+ .write = sunsu_console_write,
+ .device = uart_console_device,
+ .setup = sunsu_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &sunsu_reg,
+};
+
+/*
+ * Register console.
+ */
+
+static inline struct console *SUNSU_CONSOLE(void)
+{
+ return &sunsu_console;
+}
+#else
+#define SUNSU_CONSOLE() (NULL)
+#define sunsu_serial_console_init() do { } while (0)
+#endif
+
+static enum su_type __devinit su_get_type(struct device_node *dp)
+{
+ struct device_node *ap = of_find_node_by_path("/aliases");
+
+ if (ap) {
+ const char *keyb = of_get_property(ap, "keyboard", NULL);
+ const char *ms = of_get_property(ap, "mouse", NULL);
+
+ if (keyb) {
+ if (dp == of_find_node_by_path(keyb))
+ return SU_PORT_KBD;
+ }
+ if (ms) {
+ if (dp == of_find_node_by_path(ms))
+ return SU_PORT_MS;
+ }
+ }
+
+ return SU_PORT_PORT;
+}
+
+static int __devinit su_probe(struct platform_device *op, const struct of_device_id *match)
+{
+ static int inst;
+ struct device_node *dp = op->dev.of_node;
+ struct uart_sunsu_port *up;
+ struct resource *rp;
+ enum su_type type;
+ bool ignore_line;
+ int err;
+
+ type = su_get_type(dp);
+ if (type == SU_PORT_PORT) {
+ if (inst >= UART_NR)
+ return -EINVAL;
+ up = &sunsu_ports[inst];
+ } else {
+ up = kzalloc(sizeof(*up), GFP_KERNEL);
+ if (!up)
+ return -ENOMEM;
+ }
+
+ up->port.line = inst;
+
+ spin_lock_init(&up->port.lock);
+
+ up->su_type = type;
+
+ rp = &op->resource[0];
+ up->port.mapbase = rp->start;
+ up->reg_size = (rp->end - rp->start) + 1;
+ up->port.membase = of_ioremap(rp, 0, up->reg_size, "su");
+ if (!up->port.membase) {
+ if (type != SU_PORT_PORT)
+ kfree(up);
+ return -ENOMEM;
+ }
+
+ up->port.irq = op->archdata.irqs[0];
+
+ up->port.dev = &op->dev;
+
+ up->port.type = PORT_UNKNOWN;
+ up->port.uartclk = (SU_BASE_BAUD * 16);
+
+ err = 0;
+ if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) {
+ err = sunsu_kbd_ms_init(up);
+ if (err) {
+ of_iounmap(&op->resource[0],
+ up->port.membase, up->reg_size);
+ kfree(up);
+ return err;
+ }
+ dev_set_drvdata(&op->dev, up);
+
+ return 0;
+ }
+
+ up->port.flags |= UPF_BOOT_AUTOCONF;
+
+ sunsu_autoconfig(up);
+
+ err = -ENODEV;
+ if (up->port.type == PORT_UNKNOWN)
+ goto out_unmap;
+
+ up->port.ops = &sunsu_pops;
+
+ ignore_line = false;
+ if (!strcmp(dp->name, "rsc-console") ||
+ !strcmp(dp->name, "lom-console"))
+ ignore_line = true;
+
+ sunserial_console_match(SUNSU_CONSOLE(), dp,
+ &sunsu_reg, up->port.line,
+ ignore_line);
+ err = uart_add_one_port(&sunsu_reg, &up->port);
+ if (err)
+ goto out_unmap;
+
+ dev_set_drvdata(&op->dev, up);
+
+ inst++;
+
+ return 0;
+
+out_unmap:
+ of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
+ return err;
+}
+
+static int __devexit su_remove(struct platform_device *op)
+{
+ struct uart_sunsu_port *up = dev_get_drvdata(&op->dev);
+ bool kbdms = false;
+
+ if (up->su_type == SU_PORT_MS ||
+ up->su_type == SU_PORT_KBD)
+ kbdms = true;
+
+ if (kbdms) {
+#ifdef CONFIG_SERIO
+ serio_unregister_port(&up->serio);
+#endif
+ } else if (up->port.type != PORT_UNKNOWN)
+ uart_remove_one_port(&sunsu_reg, &up->port);
+
+ if (up->port.membase)
+ of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
+
+ if (kbdms)
+ kfree(up);
+
+ dev_set_drvdata(&op->dev, NULL);
+
+ return 0;
+}
+
+static const struct of_device_id su_match[] = {
+ {
+ .name = "su",
+ },
+ {
+ .name = "su_pnp",
+ },
+ {
+ .name = "serial",
+ .compatible = "su",
+ },
+ {
+ .type = "serial",
+ .compatible = "su",
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, su_match);
+
+static struct of_platform_driver su_driver = {
+ .driver = {
+ .name = "su",
+ .owner = THIS_MODULE,
+ .of_match_table = su_match,
+ },
+ .probe = su_probe,
+ .remove = __devexit_p(su_remove),
+};
+
+static int __init sunsu_init(void)
+{
+ struct device_node *dp;
+ int err;
+ int num_uart = 0;
+
+ for_each_node_by_name(dp, "su") {
+ if (su_get_type(dp) == SU_PORT_PORT)
+ num_uart++;
+ }
+ for_each_node_by_name(dp, "su_pnp") {
+ if (su_get_type(dp) == SU_PORT_PORT)
+ num_uart++;
+ }
+ for_each_node_by_name(dp, "serial") {
+ if (of_device_is_compatible(dp, "su")) {
+ if (su_get_type(dp) == SU_PORT_PORT)
+ num_uart++;
+ }
+ }
+ for_each_node_by_type(dp, "serial") {
+ if (of_device_is_compatible(dp, "su")) {
+ if (su_get_type(dp) == SU_PORT_PORT)
+ num_uart++;
+ }
+ }
+
+ if (num_uart) {
+ err = sunserial_register_minors(&sunsu_reg, num_uart);
+ if (err)
+ return err;
+ }
+
+ err = of_register_platform_driver(&su_driver);
+ if (err && num_uart)
+ sunserial_unregister_minors(&sunsu_reg, num_uart);
+
+ return err;
+}
+
+static void __exit sunsu_exit(void)
+{
+ if (sunsu_reg.nr)
+ sunserial_unregister_minors(&sunsu_reg, sunsu_reg.nr);
+}
+
+module_init(sunsu_init);
+module_exit(sunsu_exit);
+
+MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller");
+MODULE_DESCRIPTION("Sun SU serial port driver");
+MODULE_VERSION("2.0");
+MODULE_LICENSE("GPL");