diff options
Diffstat (limited to 'include/asm-arm/arch-l7200/serial_l7200.h')
| -rw-r--r-- | include/asm-arm/arch-l7200/serial_l7200.h | 101 |
1 files changed, 0 insertions, 101 deletions
diff --git a/include/asm-arm/arch-l7200/serial_l7200.h b/include/asm-arm/arch-l7200/serial_l7200.h deleted file mode 100644 index b1008a9d23e..00000000000 --- a/include/asm-arm/arch-l7200/serial_l7200.h +++ /dev/null @@ -1,101 +0,0 @@ -/* - * linux/include/asm-arm/arch-l7200/serial_l7200.h - * - * Copyright (c) 2000 Steven Hill (sjhill@cotw.com) - * - * Changelog: - * 05-09-2000 SJH Created - */ -#ifndef __ASM_ARCH_SERIAL_L7200_H -#define __ASM_ARCH_SERIAL_L7200_H - -#include <asm/arch/memory.h> - -/* - * This assumes you have a 3.6864 MHz clock for your UART. - */ -#define BASE_BAUD 3686400 - -/* - * UART base register addresses - */ -#define UART1_BASE (IO_BASE + 0x00044000) -#define UART2_BASE (IO_BASE + 0x00045000) - -/* - * UART register offsets - */ -#define UARTDR 0x00 /* Tx/Rx data */ -#define RXSTAT 0x04 /* Rx status */ -#define H_UBRLCR 0x08 /* mode register high */ -#define M_UBRLCR 0x0C /* mode reg mid (MSB of baud)*/ -#define L_UBRLCR 0x10 /* mode reg low (LSB of baud)*/ -#define UARTCON 0x14 /* control register */ -#define UARTFLG 0x18 /* flag register */ -#define UARTINTSTAT 0x1C /* FIFO IRQ status register */ -#define UARTINTMASK 0x20 /* FIFO IRQ mask register */ - -/* - * UART baud rate register values - */ -#define BR_110 0x827 -#define BR_1200 0x06e -#define BR_2400 0x05f -#define BR_4800 0x02f -#define BR_9600 0x017 -#define BR_14400 0x00f -#define BR_19200 0x00b -#define BR_38400 0x005 -#define BR_57600 0x003 -#define BR_76800 0x002 -#define BR_115200 0x001 - -/* - * Receiver status register (RXSTAT) mask values - */ -#define RXSTAT_NO_ERR 0x00 /* No error */ -#define RXSTAT_FRM_ERR 0x01 /* Framing error */ -#define RXSTAT_PAR_ERR 0x02 /* Parity error */ -#define RXSTAT_OVR_ERR 0x04 /* Overrun error */ - -/* - * High byte of UART bit rate and line control register (H_UBRLCR) values - */ -#define UBRLCR_BRK 0x01 /* generate break on tx */ -#define UBRLCR_PEN 0x02 /* enable parity */ -#define UBRLCR_PDIS 0x00 /* disable parity */ -#define UBRLCR_EVEN 0x04 /* 1= even parity,0 = odd parity */ -#define UBRLCR_STP2 0x08 /* transmit 2 stop bits */ -#define UBRLCR_FIFO 0x10 /* enable FIFO */ -#define UBRLCR_LEN5 0x60 /* word length5 */ -#define UBRLCR_LEN6 0x40 /* word length6 */ -#define UBRLCR_LEN7 0x20 /* word length7 */ -#define UBRLCR_LEN8 0x00 /* word length8 */ - -/* - * UART control register (UARTCON) values - */ -#define UARTCON_UARTEN 0x01 /* Enable UART */ -#define UARTCON_DMAONERR 0x08 /* Mask RxDmaRq when errors occur */ - -/* - * UART flag register (UARTFLG) mask values - */ -#define UARTFLG_UTXFF 0x20 /* Transmit FIFO full */ -#define UARTFLG_URXFE 0x10 /* Receiver FIFO empty */ -#define UARTFLG_UBUSY 0x08 /* Transmitter busy */ -#define UARTFLG_DCD 0x04 /* Data carrier detect */ -#define UARTFLG_DSR 0x02 /* Data set ready */ -#define UARTFLG_CTS 0x01 /* Clear to send */ - -/* - * UART interrupt status/clear registers (UARTINTSTAT/CLR) values - */ -#define UART_TXINT 0x01 /* TX interrupt */ -#define UART_RXINT 0x02 /* RX interrupt */ -#define UART_RXERRINT 0x04 /* RX error interrupt */ -#define UART_MSINT 0x08 /* Modem Status interrupt */ -#define UART_UDINT 0x10 /* UART Disabled interrupt */ -#define UART_ALLIRQS 0x1f /* All interrupts */ - -#endif |