diff options
Diffstat (limited to 'include/net/mac80211.h')
| -rw-r--r-- | include/net/mac80211.h | 313 |
1 files changed, 225 insertions, 88 deletions
diff --git a/include/net/mac80211.h b/include/net/mac80211.h index ee50c5eba50..f7eba1300d8 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -147,10 +147,12 @@ struct ieee80211_low_level_stats { * enum ieee80211_chanctx_change - change flag for channel context * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed + * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed */ enum ieee80211_chanctx_change { IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0), IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1), + IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2), }; /** @@ -165,6 +167,7 @@ enum ieee80211_chanctx_change { * @rx_chains_dynamic: The number of RX chains that must be enabled * after RTS/CTS handshake to receive SMPS MIMO transmissions; * this will always be >= @rx_chains_static. + * @radar_enabled: whether radar detection is enabled on this channel. * @drv_priv: data area for driver use, will always be aligned to * sizeof(void *), size is determined in hw information. */ @@ -173,7 +176,9 @@ struct ieee80211_chanctx_conf { u8 rx_chains_static, rx_chains_dynamic; - u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); + bool radar_enabled; + + u8 drv_priv[0] __aligned(sizeof(void *)); }; /** @@ -208,6 +213,11 @@ struct ieee80211_chanctx_conf { * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS) * changed (currently only in P2P client mode, GO mode will be later) + * @BSS_CHANGED_DTIM_PERIOD: the DTIM period value was changed (set when + * it becomes valid, managed mode only) + * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed, + * note that this is only called when it changes after the channel + * context had been assigned. */ enum ieee80211_bss_change { BSS_CHANGED_ASSOC = 1<<0, @@ -230,6 +240,8 @@ enum ieee80211_bss_change { BSS_CHANGED_PS = 1<<17, BSS_CHANGED_TXPOWER = 1<<18, BSS_CHANGED_P2P_PS = 1<<19, + BSS_CHANGED_DTIM_PERIOD = 1<<20, + BSS_CHANGED_BANDWIDTH = 1<<21, /* when adding here, make sure to change ieee80211_reconfig */ }; @@ -271,13 +283,19 @@ enum ieee80211_rssi_event { * if the hardware cannot handle this it must set the * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag * @dtim_period: num of beacons before the next DTIM, for beaconing, - * valid in station mode only while @assoc is true and if also - * requested by %IEEE80211_HW_NEED_DTIM_PERIOD (cf. also hw conf - * @ps_dtim_period) + * valid in station mode only if after the driver was notified + * with the %BSS_CHANGED_DTIM_PERIOD flag, will be non-zero then. * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old - * as it may have been received during scanning long ago) + * as it may have been received during scanning long ago). If the + * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can + * only come from a beacon, but might not become valid until after + * association when a beacon is received (which is notified with the + * %BSS_CHANGED_DTIM flag.) * @sync_device_ts: the device timestamp corresponding to the sync_tsf, * the driver/device can use this to calculate synchronisation + * (see @sync_tsf) + * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY + * is requested, see @sync_tsf/@sync_device_ts. * @beacon_int: beacon interval * @assoc_capability: capabilities taken from assoc resp * @basic_rates: bitmap of basic rates, each bit stands for an @@ -297,11 +315,9 @@ enum ieee80211_rssi_event { * may filter ARP queries targeted for other addresses than listed here. * The driver must allow ARP queries targeted for all address listed here * to pass through. An empty list implies no ARP queries need to pass. - * @arp_addr_cnt: Number of addresses currently on the list. - * @arp_filter_enabled: Enable ARP filtering - if enabled, the hardware may - * filter ARP queries based on the @arp_addr_list, if disabled, the - * hardware must not perform any ARP filtering. Note, that the filter will - * be enabled also in promiscuous mode. + * @arp_addr_cnt: Number of addresses currently on the list. Note that this + * may be larger than %IEEE80211_BSS_ARP_ADDR_LIST_LEN (the arp_addr_list + * array size), it's up to the driver what to do in that case. * @qos: This is a QoS-enabled BSS. * @idle: This interface is idle. There's also a global idle flag in the * hardware config which may be more appropriate depending on what @@ -331,6 +347,7 @@ struct ieee80211_bss_conf { u16 assoc_capability; u64 sync_tsf; u32 sync_device_ts; + u8 sync_dtim_count; u32 basic_rates; int mcast_rate[IEEE80211_NUM_BANDS]; u16 ht_operation_mode; @@ -338,8 +355,7 @@ struct ieee80211_bss_conf { u32 cqm_rssi_hyst; struct cfg80211_chan_def chandef; __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN]; - u8 arp_addr_cnt; - bool arp_filter_enabled; + int arp_addr_cnt; bool qos; bool idle; bool ps; @@ -392,6 +408,9 @@ struct ieee80211_bss_conf { * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be * set by rate control algorithms to indicate probe rate, will * be cleared for fragmented frames (except on the last fragment) + * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate + * that a frame can be transmitted while the queues are stopped for + * off-channel operation. * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211, * used to indicate that a pending frame requires TX processing before * it can be sent out. @@ -409,6 +428,9 @@ struct ieee80211_bss_conf { * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted * after TX status because the destination was asleep, it must not * be modified again (no seqno assignment, crypto, etc.) + * @IEEE80211_TX_INTFL_MLME_CONN_TX: This frame was transmitted by the MLME + * code for connection establishment, this indicates that its status + * should kick the MLME state machine. * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211 * MLME command (internal to mac80211 to figure out whether to send TX * status to user space) @@ -454,13 +476,14 @@ enum mac80211_tx_control_flags { IEEE80211_TX_STAT_AMPDU = BIT(10), IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11), IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12), + IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13), IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14), IEEE80211_TX_INTFL_RETRIED = BIT(15), IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16), IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17), IEEE80211_TX_CTL_MORE_FRAMES = BIT(18), IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19), - /* hole at 20, use later */ + IEEE80211_TX_INTFL_MLME_CONN_TX = BIT(20), IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21), IEEE80211_TX_CTL_LDPC = BIT(22), IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24), @@ -953,6 +976,7 @@ enum ieee80211_smps_mode { * * @channel: the channel to tune to * @channel_type: the channel (HT) type + * @radar_enabled: whether radar detection is enabled * * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11, @@ -979,6 +1003,7 @@ struct ieee80211_conf { struct ieee80211_channel *channel; enum nl80211_channel_type channel_type; + bool radar_enabled; enum ieee80211_smps_mode smps_mode; }; @@ -1059,7 +1084,7 @@ struct ieee80211_vif { u32 driver_flags; /* must be last */ - u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); + u8 drv_priv[0] __aligned(sizeof(void *)); }; static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) @@ -1176,6 +1201,24 @@ enum ieee80211_sta_state { }; /** + * enum ieee80211_sta_rx_bandwidth - station RX bandwidth + * @IEEE80211_STA_RX_BW_20: station can only receive 20 MHz + * @IEEE80211_STA_RX_BW_40: station can receive up to 40 MHz + * @IEEE80211_STA_RX_BW_80: station can receive up to 80 MHz + * @IEEE80211_STA_RX_BW_160: station can receive up to 160 MHz + * (including 80+80 MHz) + * + * Implementation note: 20 must be zero to be initialized + * correctly, the values must be sorted. + */ +enum ieee80211_sta_rx_bandwidth { + IEEE80211_STA_RX_BW_20 = 0, + IEEE80211_STA_RX_BW_40, + IEEE80211_STA_RX_BW_80, + IEEE80211_STA_RX_BW_160, +}; + +/** * struct ieee80211_sta - station table entry * * A station table entry represents a station we are possibly @@ -1197,6 +1240,12 @@ enum ieee80211_sta_state { * @uapsd_queues: bitmap of queues configured for uapsd. Only valid * if wme is supported. * @max_sp: max Service Period. Only valid if wme is supported. + * @bandwidth: current bandwidth the station can receive with + * @rx_nss: in HT/VHT, the maximum number of spatial streams the + * station can receive at the moment, changed by operating mode + * notifications and capabilities. The value is only valid after + * the station moves to associated state. + * @smps_mode: current SMPS mode (off, static or dynamic) */ struct ieee80211_sta { u32 supp_rates[IEEE80211_NUM_BANDS]; @@ -1207,9 +1256,12 @@ struct ieee80211_sta { bool wme; u8 uapsd_queues; u8 max_sp; + u8 rx_nss; + enum ieee80211_sta_rx_bandwidth bandwidth; + enum ieee80211_smps_mode smps_mode; /* must be last */ - u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); + u8 drv_priv[0] __aligned(sizeof(void *)); }; /** @@ -1331,9 +1383,9 @@ struct ieee80211_tx_control { * When this flag is set, signaling beacon-loss will cause an immediate * change to disassociated state. * - * @IEEE80211_HW_NEED_DTIM_PERIOD: - * This device needs to know the DTIM period for the BSS before - * associating. + * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC: + * This device needs to get data from beacon before association (i.e. + * dtim_period). * * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports * per-station GTKs as used by IBSS RSN or during fast transition. If @@ -1353,10 +1405,6 @@ struct ieee80211_tx_control { * setup strictly in HW. mac80211 should not attempt to do this in * software. * - * @IEEE80211_HW_SCAN_WHILE_IDLE: The device can do hw scan while - * being idle (i.e. mac80211 doesn't have to go idle-off during the - * the scan). - * * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of * a virtual monitor interface when monitor interfaces are the only * active interfaces. @@ -1370,9 +1418,8 @@ struct ieee80211_tx_control { * P2P Interface. This will be honoured even if more than one interface * is supported. * - * @IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL: On this hardware TX BA session - * should be tear down once BAR frame will not be acked. - * + * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames + * only, to allow getting TBTT of a DTIM beacon. */ enum ieee80211_hw_flags { IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, @@ -1382,7 +1429,7 @@ enum ieee80211_hw_flags { IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, IEEE80211_HW_SIGNAL_UNSPEC = 1<<5, IEEE80211_HW_SIGNAL_DBM = 1<<6, - IEEE80211_HW_NEED_DTIM_PERIOD = 1<<7, + IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC = 1<<7, IEEE80211_HW_SPECTRUM_MGMT = 1<<8, IEEE80211_HW_AMPDU_AGGREGATION = 1<<9, IEEE80211_HW_SUPPORTS_PS = 1<<10, @@ -1399,9 +1446,8 @@ enum ieee80211_hw_flags { IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21, IEEE80211_HW_AP_LINK_PS = 1<<22, IEEE80211_HW_TX_AMPDU_SETUP_IN_HW = 1<<23, - IEEE80211_HW_SCAN_WHILE_IDLE = 1<<24, IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF = 1<<25, - IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL = 1<<26, + IEEE80211_HW_TIMING_BEACON_ONLY = 1<<26, }; /** @@ -1522,6 +1568,8 @@ struct ieee80211_hw { * structure can then access it via hw->priv. Note that mac802111 drivers should * not use wiphy_priv() to try to get their private driver structure as this * is already used internally by mac80211. + * + * Return: The mac80211 driver hw struct of @wiphy. */ struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy); @@ -1628,6 +1676,10 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is * provided by update_tkip_key only. The trigger that makes mac80211 call this * handler is software decryption with wrap around of iv16. + * + * The set_default_unicast_key() call updates the default WEP key index + * configured to the hardware for WEP encryption type. This is required + * for devices that support offload of data packets (e.g. ARP responses). */ /** @@ -1680,15 +1732,6 @@ void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS * enabled whenever user has enabled powersave. * - * Some hardware need to toggle a single shared antenna between WLAN and - * Bluetooth to facilitate co-existence. These types of hardware set - * limitations on the use of host controlled dynamic powersave whenever there - * is simultaneous WLAN and Bluetooth traffic. For these types of hardware, the - * driver may request temporarily going into full power save, in order to - * enable toggling the antenna between BT and WLAN. If the driver requests - * disabling dynamic powersave, the @dynamic_ps_timeout value will be - * temporarily set to zero until the driver re-enables dynamic powersave. - * * Driver informs U-APSD client support by enabling * %IEEE80211_HW_SUPPORTS_UAPSD flag. The mode is configured through the * uapsd paramater in conf_tx() operation. Hardware needs to send the QoS @@ -2033,17 +2076,29 @@ enum ieee80211_filter_flags { * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer * might receive the addBA frame and send a delBA right away! * - * @IEEE80211_AMPDU_RX_START: start Rx aggregation - * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation - * @IEEE80211_AMPDU_TX_START: start Tx aggregation - * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation + * @IEEE80211_AMPDU_RX_START: start RX aggregation + * @IEEE80211_AMPDU_RX_STOP: stop RX aggregation + * @IEEE80211_AMPDU_TX_START: start TX aggregation * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational + * @IEEE80211_AMPDU_TX_STOP_CONT: stop TX aggregation but continue transmitting + * queued packets, now unaggregated. After all packets are transmitted the + * driver has to call ieee80211_stop_tx_ba_cb_irqsafe(). + * @IEEE80211_AMPDU_TX_STOP_FLUSH: stop TX aggregation and flush all packets, + * called when the station is removed. There's no need or reason to call + * ieee80211_stop_tx_ba_cb_irqsafe() in this case as mac80211 assumes the + * session is gone and removes the station. + * @IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: called when TX aggregation is stopped + * but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe() yet and + * now the connection is dropped and the station will be removed. Drivers + * should clean up and drop remaining packets when this is called. */ enum ieee80211_ampdu_mlme_action { IEEE80211_AMPDU_RX_START, IEEE80211_AMPDU_RX_STOP, IEEE80211_AMPDU_TX_START, - IEEE80211_AMPDU_TX_STOP, + IEEE80211_AMPDU_TX_STOP_CONT, + IEEE80211_AMPDU_TX_STOP_FLUSH, + IEEE80211_AMPDU_TX_STOP_FLUSH_CONT, IEEE80211_AMPDU_TX_OPERATIONAL, }; @@ -2062,16 +2117,21 @@ enum ieee80211_frame_release_type { * enum ieee80211_rate_control_changed - flags to indicate what changed * * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit - * to this station changed. + * to this station changed. The actual bandwidth is in the station + * information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40 + * flag changes, for HT and VHT the bandwidth field changes. * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed. * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer * changed (in IBSS mode) due to discovering more information about * the peer. + * @IEEE80211_RC_NSS_CHANGED: N_SS (number of spatial streams) was changed + * by the peer */ enum ieee80211_rate_control_changed { IEEE80211_RC_BW_CHANGED = BIT(0), IEEE80211_RC_SMPS_CHANGED = BIT(1), IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2), + IEEE80211_RC_NSS_CHANGED = BIT(3), }; /** @@ -2152,6 +2212,18 @@ enum ieee80211_rate_control_changed { * MAC address of the device going away. * Hence, this callback must be implemented. It can sleep. * + * @add_interface_debugfs: Drivers can use this callback to add debugfs files + * when a vif is added to mac80211. This callback and + * @remove_interface_debugfs should be within a CONFIG_MAC80211_DEBUGFS + * conditional. @remove_interface_debugfs must be provided for cleanup. + * This callback can sleep. + * + * @remove_interface_debugfs: Remove the debugfs files which were added using + * @add_interface_debugfs. This callback must remove all debugfs entries + * that were added because mac80211 only removes interface debugfs when the + * interface is destroyed, not when it is removed from the driver. + * This callback can sleep. + * * @config: Handler for configuration requests. IEEE 802.11 code calls this * function to change hardware configuration, e.g., channel. * This function should never fail but returns a negative error code @@ -2194,6 +2266,10 @@ enum ieee80211_rate_control_changed { * After rekeying was done it should (for example during resume) notify * userspace of the new replay counter using ieee80211_gtk_rekey_notify(). * + * @set_default_unicast_key: Set the default (unicast) key index, useful for + * WEP when the device sends data packets autonomously, e.g. for ARP + * offloading. The index can be 0-3, or -1 for unsetting it. + * * @hw_scan: Ask the hardware to service the scan request, no need to start * the scan state machine in stack. The scan must honour the channel * configuration done by the regulatory agent in the wiphy's @@ -2474,7 +2550,13 @@ enum ieee80211_rate_control_changed { * * @restart_complete: Called after a call to ieee80211_restart_hw(), when the * reconfiguration has completed. This can help the driver implement the - * reconfiguration step. This callback may sleep. + * reconfiguration step. Also called when reconfiguring because the + * driver's resume function returned 1, as this is just like an "inline" + * hardware restart. This callback may sleep. + * + * @ipv6_addr_change: IPv6 address assignment on the given interface changed. + * Currently, this is only called for managed or P2P client interfaces. + * This callback is optional; it must not sleep. */ struct ieee80211_ops { void (*tx)(struct ieee80211_hw *hw, @@ -2522,6 +2604,8 @@ struct ieee80211_ops { void (*set_rekey_data)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct cfg80211_gtk_rekey_data *data); + void (*set_default_unicast_key)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, int idx); int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct cfg80211_scan_request *req); void (*cancel_hw_scan)(struct ieee80211_hw *hw, @@ -2553,6 +2637,12 @@ struct ieee80211_ops { struct ieee80211_vif *vif, struct ieee80211_sta *sta, struct dentry *dir); + void (*add_interface_debugfs)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct dentry *dir); + void (*remove_interface_debugfs)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct dentry *dir); #endif void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, enum sta_notify_cmd, struct ieee80211_sta *sta); @@ -2606,6 +2696,7 @@ struct ieee80211_ops { int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, const struct cfg80211_bitrate_mask *mask); void (*rssi_callback)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, enum ieee80211_rssi_event rssi_event); void (*allow_buffered_frames)(struct ieee80211_hw *hw, @@ -2648,6 +2739,12 @@ struct ieee80211_ops { struct ieee80211_chanctx_conf *ctx); void (*restart_complete)(struct ieee80211_hw *hw); + +#if IS_ENABLED(CONFIG_IPV6) + void (*ipv6_addr_change)(struct ieee80211_hw *hw, + struct ieee80211_vif *vif, + struct inet6_dev *idev); +#endif }; /** @@ -2661,6 +2758,8 @@ struct ieee80211_ops { * * @priv_data_len: length of private data * @ops: callbacks for this device + * + * Return: A pointer to the new hardware device, or %NULL on error. */ struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, const struct ieee80211_ops *ops); @@ -2673,6 +2772,8 @@ struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, * need to fill the contained wiphy's information. * * @hw: the device to register as returned by ieee80211_alloc_hw() + * + * Return: 0 on success. An error code otherwise. */ int ieee80211_register_hw(struct ieee80211_hw *hw); @@ -2719,6 +2820,8 @@ extern char *__ieee80211_create_tpt_led_trigger( * of the trigger so you can automatically link the LED device. * * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) { @@ -2738,6 +2841,8 @@ static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) * of the trigger so you can automatically link the LED device. * * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) { @@ -2757,6 +2862,8 @@ static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) * of the trigger so you can automatically link the LED device. * * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) { @@ -2776,6 +2883,8 @@ static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) * of the trigger so you can automatically link the LED device. * * @hw: the hardware to get the LED trigger name for + * + * Return: The name of the LED trigger. %NULL if not configured for LEDs. */ static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) { @@ -2793,9 +2902,10 @@ static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) * @blink_table: the blink table -- needs to be ordered by throughput * @blink_table_len: size of the blink table * - * This function returns %NULL (in case of error, or if no LED - * triggers are configured) or the name of the new trigger. - * This function must be called before ieee80211_register_hw(). + * Return: %NULL (in case of error, or if no LED triggers are + * configured) or the name of the new trigger. + * + * Note: This function must be called before ieee80211_register_hw(). */ static inline char * ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags, @@ -2928,10 +3038,10 @@ static inline void ieee80211_rx_ni(struct ieee80211_hw *hw, * Calls to this function for a single hardware must be synchronized against * each other. * - * The function returns -EINVAL when the requested PS mode is already set. - * * @sta: currently connected sta * @start: start or stop PS + * + * Return: 0 on success. -EINVAL when the requested PS mode is already set. */ int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start); @@ -2945,6 +3055,8 @@ int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start); * * @sta: currently connected sta * @start: start or stop PS + * + * Return: Like ieee80211_sta_ps_transition(). */ static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta, bool start) @@ -3082,6 +3194,8 @@ void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); * according to the current DTIM parameters/TIM bitmap. * * The driver is responsible for freeing the returned skb. + * + * Return: The beacon template. %NULL on error. */ struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw, struct ieee80211_vif *vif, @@ -3093,6 +3207,8 @@ struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw, * @vif: &struct ieee80211_vif pointer from the add_interface callback. * * See ieee80211_beacon_get_tim(). + * + * Return: See ieee80211_beacon_get_tim(). */ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif) @@ -3109,6 +3225,8 @@ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, * hardware. The destination address should be set by the caller. * * Can only be called in AP mode. + * + * Return: The Probe Response template. %NULL on error. */ struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif); @@ -3124,6 +3242,8 @@ struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw, * * Note: Caller (or hardware) is responsible for setting the * &IEEE80211_FCTL_PM bit. + * + * Return: The PS Poll template. %NULL on error. */ struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif); @@ -3139,6 +3259,8 @@ struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw, * * Note: Caller (or hardware) is responsible for setting the * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields. + * + * Return: The nullfunc template. %NULL on error. */ struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif); @@ -3153,6 +3275,8 @@ struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw, * * Creates a Probe Request template which can, for example, be uploaded to * hardware. + * + * Return: The Probe Request template. %NULL on error. */ struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif, @@ -3188,6 +3312,8 @@ void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif, * If the RTS is generated in firmware, but the host system must provide * the duration field, the low-level driver uses this function to receive * the duration field value in little-endian byteorder. + * + * Return: The duration. */ __le16 ieee80211_rts_duration(struct ieee80211_hw *hw, struct ieee80211_vif *vif, size_t frame_len, @@ -3223,6 +3349,8 @@ void ieee80211_ctstoself_get(struct ieee80211_hw *hw, * If the CTS-to-self is generated in firmware, but the host system must provide * the duration field, the low-level driver uses this function to receive * the duration field value in little-endian byteorder. + * + * Return: The duration. */ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, struct ieee80211_vif *vif, @@ -3239,6 +3367,8 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, * * Calculate the duration field of some generic frame, given its * length and transmission rate (in 100kbps). + * + * Return: The duration. */ __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, struct ieee80211_vif *vif, @@ -3255,9 +3385,10 @@ __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, * hardware/firmware does not implement buffering of broadcast/multicast * frames when power saving is used, 802.11 code buffers them in the host * memory. The low-level driver uses this function to fetch next buffered - * frame. In most cases, this is used when generating beacon frame. This - * function returns a pointer to the next buffered skb or NULL if no more - * buffered frames are available. + * frame. In most cases, this is used when generating beacon frame. + * + * Return: A pointer to the next buffered skb or NULL if no more buffered + * frames are available. * * Note: buffered frames are returned only after DTIM beacon frame was * generated with ieee80211_beacon_get() and the low-level driver must thus @@ -3437,6 +3568,8 @@ void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue); * @queue: queue number (counted from zero). * * Drivers should use this function instead of netif_stop_queue. + * + * Return: %true if the queue is stopped. %false otherwise. */ int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue); @@ -3634,7 +3767,9 @@ void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra, * @vif: virtual interface to look for station on * @addr: station's address * - * This function must be called under RCU lock and the + * Return: The station, if found. %NULL otherwise. + * + * Note: This function must be called under RCU lock and the * resulting pointer is only valid under RCU lock as well. */ struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif, @@ -3647,7 +3782,9 @@ struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif, * @addr: remote station's address * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'. * - * This function must be called under RCU lock and the + * Return: The station, if found. %NULL otherwise. + * + * Note: This function must be called under RCU lock and the * resulting pointer is only valid under RCU lock as well. * * NOTE: You may pass NULL for localaddr, but then you will just get @@ -3754,6 +3891,11 @@ void ieee80211_iter_keys(struct ieee80211_hw *hw, * The iterator will not find a context that's being added (during * the driver callback to add it) but will find it while it's being * removed. + * + * Note that during hardware restart, all contexts that existed + * before the restart are considered already present so will be + * found while iterating, whether they've been re-added already + * or not. */ void ieee80211_iter_chan_contexts_atomic( struct ieee80211_hw *hw, @@ -3772,7 +3914,9 @@ void ieee80211_iter_chan_contexts_atomic( * information. This function must only be called from within the * .bss_info_changed callback function and only in managed mode. The function * is only useful when the interface is associated, otherwise it will return - * NULL. + * %NULL. + * + * Return: The Probe Request template. %NULL on error. */ struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif); @@ -3796,6 +3940,8 @@ void ieee80211_beacon_loss(struct ieee80211_vif *vif); * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver * needs to inform if the connection to the AP has been lost. + * The function may also be called if the connection needs to be terminated + * for some other reason, even if %IEEE80211_HW_CONNECTION_MONITOR isn't set. * * This function will cause immediate change to disassociated state, * without connection recovery attempts. @@ -3826,36 +3972,6 @@ void ieee80211_connection_loss(struct ieee80211_vif *vif); void ieee80211_resume_disconnect(struct ieee80211_vif *vif); /** - * ieee80211_disable_dyn_ps - force mac80211 to temporarily disable dynamic psm - * - * @vif: &struct ieee80211_vif pointer from the add_interface callback. - * - * Some hardware require full power save to manage simultaneous BT traffic - * on the WLAN frequency. Full PSM is required periodically, whenever there are - * burst of BT traffic. The hardware gets information of BT traffic via - * hardware co-existence lines, and consequentially requests mac80211 to - * (temporarily) enter full psm. - * This function will only temporarily disable dynamic PS, not enable PSM if - * it was not already enabled. - * The driver must make sure to re-enable dynamic PS using - * ieee80211_enable_dyn_ps() if the driver has disabled it. - * - */ -void ieee80211_disable_dyn_ps(struct ieee80211_vif *vif); - -/** - * ieee80211_enable_dyn_ps - restore dynamic psm after being disabled - * - * @vif: &struct ieee80211_vif pointer from the add_interface callback. - * - * This function restores dynamic PS after being temporarily disabled via - * ieee80211_disable_dyn_ps(). Each ieee80211_disable_dyn_ps() call must - * be coupled with an eventual call to this function. - * - */ -void ieee80211_enable_dyn_ps(struct ieee80211_vif *vif); - -/** * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring * rssi threshold triggered * @@ -3872,6 +3988,13 @@ void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif, gfp_t gfp); /** + * ieee80211_radar_detected - inform that a radar was detected + * + * @hw: pointer as obtained from ieee80211_alloc_hw() + */ +void ieee80211_radar_detected(struct ieee80211_hw *hw); + +/** * ieee80211_chswitch_done - Complete channel switch process * @vif: &struct ieee80211_vif pointer from the add_interface callback. * @success: make the channel switch successful or not @@ -4119,13 +4242,27 @@ void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif, void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif); /** - * ieee80211_ave_rssi - report the average rssi for the specified interface + * ieee80211_ave_rssi - report the average RSSI for the specified interface * * @vif: the specified virtual interface * - * This function return the average rssi value for the requested interface. - * It assumes that the given vif is valid. + * Note: This function assumes that the given vif is valid. + * + * Return: The average RSSI value for the requested interface, or 0 if not + * applicable. */ int ieee80211_ave_rssi(struct ieee80211_vif *vif); +/** + * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup + * @vif: virtual interface + * @wakeup: wakeup reason(s) + * @gfp: allocation flags + * + * See cfg80211_report_wowlan_wakeup(). + */ +void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif, + struct cfg80211_wowlan_wakeup *wakeup, + gfp_t gfp); + #endif /* MAC80211_H */ |