summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/intel/i40e
AgeCommit message (Collapse)Author
2015-02-26i40e: check pointers before useShannon Nelson
Make sure we don't try to dereference NULL pointers when returning values from the AdminQ calls. Change-ID: Ia6694f2f415d50acf0aba063c863568742799aff Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: catch NVM write semaphore timeout and retryShannon Nelson
In some circumstances, a multi-write transaction takes longer than the default 3 minute timeout on the write semaphore. If the write failed with an EBUSY status, this is likely the problem, so here we try to reacquire the semaphore then retry the write. We only do one retry, then give up. Change-ID: I1c8be60688acc2f39573839579baf601207c4a36 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: stop flow director on shutdownMitch A Williams
In some cases, the hardware would continue to try to access the FDIR ring after entering D3Hot state, which would cause either PCIe errors or NMIs, depending upon system configuration. Explicitly stop FDIR in our shutdown routine to eliminate this possibility. Change-ID: I1bd9fc7fd8f151fe24cad132ac9adddab923e3af Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: disconnect irqs on shutdownShannon Nelson
Combine the ICR0 shutdown with the standard interrupt shutdown, and add the interrupt clearing to the PCI shutdown path. This prevents the driver from allowing stray interrupts or causing system logs from un-handled interrupts. Change-ID: I48f6ab95cad7f8ca77c1f26c92a51cc1034ced43 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: Issue a PF reset if Tx queue disable timeoutParikh, Neerav
As part of DCB reconfiguration flow if the Tx queue disable times out then issue a PF reset to do some level of recovery. Change-ID: I7550021c55bff355351c0365e61e1f05fcaff46d Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: Fix the Tx ring qset handle when DCB reconfiguresParikh, Neerav
When DCB is reconfigured to single TC the driver did not reset the Tx ring Qset handle to the correct mapping; which caused Tx queue disable timeouts. Change-ID: I4da5915ec92a83c281b478d653fae6ef1b72edfe Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: Fix the case where per TC queue count was higher than queues enabledAnjali Singhai
When the driver or hardware gets less interrupt vectors than the actual number of CPU cores, limit the queue count for the priority queue traffic class (TC) queues. This will fix a warning with multiple function mode where systems regularly have more cores than vectors. Also add extra comment for readability. Change-ID: I4f02226263aa3995e1f5ee5503eac0cd6ee12fbd Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: fix race in hang checkJesse Brandeburg
The driver was having some issues with false Tx hang detection. This makes the driver a little more direct with the checks for progress forward by directly checking the head write back address and tail register when determining progress. This avoids Tx hangs where the software gets behind, because we are directly checking hardware state when determining hang state. Change-ID: I774f0e861c9e8ab5ccb213634100fe15440ae24a Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: Fix TSO with more than 8 frags per segment issueAnjali Singhai
The hardware has some limitations the driver needs to adhere to, that we found in extended testing. 1) no more than 8 descriptors per packet on the wire 2) no header can span more than 3 descriptors If one of these events occurs, the hardware will generate an internal error and freeze the Tx queue. This patch linearizes the skb to avoid these situations. Change-ID: I37dab7d3966e14895a9663ec4d0aaa8eb0d9e115 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: Don't check for Tx hang when PF downAkeem G Abodunrin
This patch adds check to bail out if device is already down when checking for Tx hang subtask. Change-ID: I3853fb7a6d11cb9a4c349b687cb25c15b19977a0 Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: fix shift precedence issueShannon Nelson
Add parens to make sure the shift and bitwise precedences don't work backwards for us. Change-ID: I60c10ef4fad6bc654522b9d8a53da2e270a0f268 Reported-by: Joe Perches <joe@perches.com> Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-26i40e: Fix memory leak at failure path in i40e_dbg_command_write()Alexey Khoroshilov
The patch fixes a leak of 'cmd_buf' when copy_from_user() failed in i40e_dbg_command_write(). Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-09i40e: Fix for stats init function call in Rx setupCarolyn Wyborny
This patch fixes indentation issue and error found in argument reported by static analysis. Without this patch, sparse and other static analysis errors will be found. Reported-by: Fengguang Wu <fengguang.wu@intel.com> Reported-by: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-09i40e/i40evf: Add call to u64_stats_init to initCarolyn Wyborny
This patch adds a call to u64_stats_init to Rx setup. This done in order to avoid lockdep errors with seqcount on newer kernels. Change-ID: Ia8ba8f0bcbd1c0e926f97d70aeee4ce4fd055e93 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-09i40e: Enable Loopback for the FCOE vsi as wellAnjali Singhai Jain
For all VSIs on a VEB, Loopback mode should be either on or off. Our configuration requires them to be ON so that VSIs can directly talk to each other without going out on the wire. Change-ID: I77b8310bc846329972b13b185949ab1431a46c30 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-09i40e: use dev_port for fcoe netdevVasu Dev
Set different dev_port value 1 for FCoE netdev than the default zero dev_port value for PF netdev, this helps biosdevname user tool to differentiate them correctly while both attached to the same PCI function. Change-ID: I8fb90e4ef52a1242f7580e49a3f0918735aee8ef Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-09i40e: Fix function headerGreg Rose
s/enable/disable Change-ID: Ic0572a6c59d03e05a0a35d2e2e9d532e0512638d Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-09i40e: fix led blink toggle to enable steady stateMatt Jared
Make sure to clear the GPIO blink field, instead of OR'ing against zero if the field is already '1'. Change-ID: Ie52a52abd48f6f52b20778a6b8b0c542dfc9245c Signed-off-by: Matt Jared <matthew.a.jared@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-09i40evf: Force Tx writeback on ITRAnjali Singhai Jain
This patch forces Tx descriptor writebacks on ITR by kicking off the SWINT interrupt when we notice that there are non-cache-aligned Tx descriptors waiting in the ring while interrupts are disabled under NAPI. Change-ID: dd6d9675629bf266c7515ad7a201394618c35444 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-08i40e: stop the service task at shutdownMitch Williams
Stop the service task in the shutdown handler, preventing it from accessing the admin queue after it had been closed. This fixes a panic that could occur when the system was shut down with a lot of VFs enabled. Change-ID: I286735e3842de472385bbf7ad68d30331e508add Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-08i40e: add locking around VF resetMitch Williams
During VF deallocation, we need to lock out the VF reset code. However, we cannot depend on simply masking the interrupt, as this does not lock out the service task, which can still call the reset routine. Instead, leave the interrupt enabled, but add locking around the VF disable and reset routines. For the disable code, we wait to get the lock, as the reset code will take a finite amount of time to run. For the reset code, we just return if we fail to get the lock. Since we know that the VFs are being disabled, we don't need to handle the reset. This fixes a panic when disabling SR-IOV. Change-ID: Iea0a6cdef35c331f48c6d5b2f8e6f0e86322e7d8 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-08i40e: Use even more ARQ descriptorsMitch Williams
When enabling 64 VFs and loading the VF driver in the host kernel, we can easily overrun the PF's admin receive queue. Double the size of this queue, and increase the work limit to allow the PF to handle more requests in a single pass through the service task. Change-ID: I0efbbdc61954bffad422a2f33c4b948a59370bf5 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-08i40e: delay after VF resetMitch Williams
Delay a minimum of 10ms after VF reset, to allow the hardware's internal FIFOs to flush. Change-ID: I8a02ddb28c9f0d7303a1eb21d0b2443e5b4c1cda Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-08i40e: avoid use of uninitialized v_budget in i40e_init_msixJohn W Linville
This I40E_FCOE block increments v_budget before it has been initialized, then v_budget gets overwritten a few lines later. This patch just reorders the code hunks in what I believe was the intended sequence. Coverity: CID 1260099 Signed-off-by: John W Linville <linville@tuxdriver.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-02-08i40e: i40e_fcoe.c: Remove unused functionRickard Strandqvist
Remove the function i40e_rx_is_fip() that is not used anywhere. This was partially found by using a static code analysis program called cppcheck. Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e/i40evf: Bump i40e and i40evf versionsSravanthi Tangeda
Bump i40e to 1.2.6 and i40evf to 1.2.0 version. Change-ID: Ice127eee3a5a5d1b8765d83cff8c30f9f3b1bc32 Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: Support for NPAR iSCSI partition with DCBNeerav Parikh
Add parsing and reporting of iSCSI capability for a given device or function. Also add support for iSCSI partition type with DCB in NPAR mode. In this mode it is expected that software would configure both the LAN and iSCSI traffic classes for the iSCSI partition; whereas all the NIC type partitions will use LAN TC (TC0) only. Hence, the patch enables querying of DCB configuration in MFP mode and configures TCs for iSCSI partition type. Though NIC type partitions may not have more than 1 TC enabled for them the port may have multiple TCs enabled and hence I40E_FLAG_DCB_ENABLED will be set/reset on all the partitions based on number of TCs on the port. This is required as in DCB environment it is expected that all traffic will be priority tagged. Change-ID: I8c6e1cfd46c46d8a39c57d9020d9ff8d42ed8a7d Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: when Rx timestamps disabled set specific modeJacob Keller
Instead of leaving the Rx timestamps in the same mode as before if we disable the Rx logic, we can set it into a mode that has the fewest possible timestamps generated. To do this, select only V1 mode, but do not enable UDP packet recognition. This should eliminate all (or at least almost all) Rx timestamps, since V1 packets are always over UDP. Change-ID: If847288e0030a716e059c4c33ab114f2cf038f05 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: use same check for Rx hang as for Rx timestampsJacob Keller
It's possible that the user configured only Tx hardware timestamping, and thus we might be receiving PTP traffic which we timestamp but which software never reads. In this case we don't want to check for Rx timestamp hang, because we already know that software won't be handling them. Thus, we add the same check against pf->ptp_rx as we have in the Rx timestamp code path. Change-ID: I66486c8dba307facbff8eace4e52e2f083789d1b Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: AQ API updates for new commandsShannon Nelson
Add lldp control commands, add oem ocsd and ocbb commands. Change-ID: I89eba2bd02013d0a44e1ce900559c54bb15f4a66 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: AQ API updatesJeff Kirsher
Fix up NVM config read and write data structs. Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: add more struct size checksShannon Nelson
Add struct size checks to many of the indirect structs and a few command structs that were left out previously. Change-ID: I7810b9af0f04e3ced670639f8671daf7df9b3f4d Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: Issue "Stop LLDP" command for firmware older than v4.3Neerav Parikh
Disable firmware LLDP agent for NICs with firmware version lower than v4.3. Added a message when driver disables the firmware LLDP agent on such NICs. Change-ID: Ia8abf89439c70cb50e23db82753d7d282265506b Signed-off-by: Neerav Parikh <neerav.parikh@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: check I40E_FLAG_PTP before handling Tx or Rx timestampsJacob Keller
We should not be doing Tx or Rx timestamps if we do not have PTP enabled. Add checks to ensure that we don't attempt to handle any PTP related timestamping code if we have not enabled PTP on that PF. Change-ID: I4335942ae2d5c5f91abfdbeeea02bcace49e7677 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: only enable PTP interrupt cause if PTP is enabledJacob Keller
We should not blindly enable the PTP interrupt flags for all PFs. We should only enable the PTP interrupt in PFs which have enabled PTP. Change-ID: I051a17cae4c199a2f3cf7852266e27eda6630525 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e/i40evf: Bump i40e/i40evf versionsCatherine Sullivan
Bump i40e to 1.2.5 and i40evf to 1.0.7. Change-ID: I622556829056e3ed42d3b9d285fc5ffb693b21cc Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: Dump Stats string removed from debugfs help commandSravanthi Tangeda
Dump Stats string has been removed from functional debugfs help message. Now it does not show up when we echo command to debugfs/Fortville queue. Change-ID: I9333473826b574f1afa6ddb785fd7adfbdcb2884 Signed-off-by: Sravanthi Tangeda <sravanthi.tangeda@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: Add define for interrupt name string lenCarolyn Wyborny
This patch creates a define for interrupt name string configuration that is large enough to contain full bus/slot info, rather than just netdev->name. Change-ID: Iaac0d23dfb8526defeed69d91cea85ed4a50ddb2 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: don't give up on DCB error after resetShannon Nelson
We don't need to give up in the reset/rebuild process if the DCB setup failed, so handle it here the same as in the probe setup. Also adjust the log strings a little to look less scary. Change-ID: I57308d703047e61d3f1a5e471ea77be232444ca0 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e: fix proc/int descriptionsCarolyn Wyborny
This patch fixes a problem where the /proc/interrupts descriptions from the msix configuration were truncating the needed bus info, making it hard to distinguish configuration from port to port. This patch increases the string buffer size in order to allow the full data to be displayed and sync's the text formatting of the misc and fdir interrupt names Change-ID: Ib01d6c61fb3f4ac70fbdf5bcc520b22638ea54b7 Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e/i40evf: Increase ASQ timeoutKevin Scott
Increase ASQ timeout for some scenarios with multi-function devices Change-ID: I2d7655b19e6c6f9a7ad04deacb106ca8d53886db Signed-off-by: Kevin Scott <kevin.c.scott@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-16i40e/i40evf: AdminQ updates ww36Shannon Nelson
Several little tweaks to keep FW, SV, and SW in line together - Remove the unused and deprecated i40e_aqc_opc_debug_modify_internals - Add define for iSCSI capability - Fix queue mask size - Adjust i40e_aqc_oem_param_change for ease-of-use Change-ID: I51f250b367912968a7cec61b3a68110d9796e914 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Kamil Kacperski <kamil.kacperski@intel.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/xen-netfront.c Minor overlapping changes in xen-netfront.c, mostly to do with some buffer management changes alongside the split of stats into TX and RX. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-14i40e: adds FCoE configure optionVasu Dev
Adds FCoE config option I40E_FCOE, so that FCoE can be enabled as needed but otherwise have it disabled by default. This also eliminate multiple FCoE config checks, instead now just one config check for CONFIG_I40E_FCOE. The I40E FCoE was added with 3.17 kernel and therefore this patch shall be applied to stable 3.17 kernel also. CC: <stable@vger.kernel.org> Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Jim Young <jamesx.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-13net: rename vlan_tx_* helpers since "tx" is misleading thereJiri Pirko
The same macros are used for rx as well. So rename it. Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
2015-01-13i40e: limit sriov to partition 1 of NPAR configurationsShannon Nelson
Make sure we only allow SR/IOV on the master PF of a port in multifunction mode. This should be the case anyway based on the num_vfs configured in the NVM, but this will help make sure there's no question. If we're not in multifunction mode the partition_id will always be 1. Change-ID: I8b2592366fe6782f15301bde2ebd1d4da240109d Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Jim Young <james.m.young@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-13i40e: Don't exit link event early if link speed has changedCatherine Sullivan
Previously we were only checking if the link up state had changed, and if it hadn't exiting the link event routine early. We should also check if speed has changed, and if it has, stay and finish processing the link event. Change-ID: I9c8e0991b3f0279108a7858898c3c5ce0a9856b8 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-13i40e: limit WoL and link settings to partition 1Shannon Nelson
When in multi-function mode, e.g. Dell's NPAR, only partition 1 of each MAC is allowed to set WoL, speed, and flow control. Change-ID: I87a9debc7479361c55a71f0120294ea319f23588 Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-13i40e: Adding function for reading PBA StringKamil Krawczyk
Function will read PBA Block from Shadow RAM and return it in a string format. Change-ID: I4ee7059f6e21bd0eba38687da15e772e0b4ab36e Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2015-01-13i40e/i40evf: find partition_id in npar modeShannon Nelson
When in NPAR mode the driver instance might be controlling the base partition or one of the other "fake" PFs. There are some things that can only be done by the base partition, aka partition_id 1. This code does a bit of work to find how many partitions are there per port and what is the current partition_id. Change-ID: Iba427f020a1983d02147d86f121b3627e20ee21d Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-04-16 14:30:24 +0000