summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath/wil6210/interrupt.c
AgeCommit message (Collapse)Author
2015-01-15wil6210: add advanced interrupt moderationVladimir Kondratiev
Add advanced interrupt moderation support available since "Sparrow B0". Legacy interrupt moderation used only one counter to moderate tx, rx, and misc interrupts. Advanced interrupt moderation bypasses misc, and handles separately tx and rx interrupts. In addition it has two timers for each interrupt type. Max burst duration timer which defines how long to postpone interrupt after first event (receive event for rx and tx complete event for tx), and interframe timeout which defines how to determine the end of the burst and issue interrupt even if the first timer still pending. Capabilities flags in wil_priv is set on initialization according to HW. The rest of the code checks for advanced interrupt capability bit in capabilities flags field. Debugfs is split accordingly: "legacy" interrupt moderation remains unchanged, new debugs files added for advanced interrupt moderation support. Module params are aligned to support advanced interrupt moderation (tx & rx). When not available (for legacy interrupt moderation) will use only rx configuration; Tx configuration will be ignored in this case. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-01-15wil6210: use HW capabilities mask in resetVladimir Kondratiev
Use the proper reset follow based on HW capabilities detection instead of chip ID. Remove old hw ID mechanism which was used only for reset flow. Remove support for Marlon A0. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2015-01-15wil6210: use bitmap API for "status"Vladimir Kondratiev
wil->status used as bitmap; use DECLARE_BITMAP for it. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2014-12-01wil6210: add handling of RX HTRSH interruptVladimir Kondratiev
RX_HTRSH interrupt is handled in exactly the same manner as RX_DONE interrupt - fetching accumulated packets from RX ring. In addition there's a rate limitted warning message. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-26wil6210: ethtool opsVladimir Kondratiev
Provide ethtool support; with support for interrupt coalescing through get_coalesce/set_coalesce. Placeholders for begin/complete will be used by runtime PM to make sure target is powered up while performing ethtool operations Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11wil6210: fix for oops while stopping interfaceVladimir Kondratiev
When interface stopped while running intensive Rx traffic, the following oops observed: [89846.734683] Call trace: [89846.737117] [<ffffffc00083aa64>] dev_gro_receive+0xac/0x358 [89846.742674] [<ffffffc00083ae94>] napi_gro_receive+0x24/0xa4 [89846.748251] [<ffffffbffc1c2f88>] $x+0xec/0x1f8 [wil6210] wil_netif_rx_any [89846.753547] [<ffffffbffc1c4830>] $x+0x34/0x54 [wil6210] wil_release_reorder_frame [89846.758755] [<ffffffbffc1c48ac>] wil_release_reorder_frames+0x5c/0x78 [wil6210] [89846.766044] [<ffffffbffc1c4bf8>] wil_tid_ampdu_rx_free+0x20/0x48 [wil6210] [89846.772901] [<ffffffbffc1bedc8>] $x+0x190/0x1e8 [wil6210] [89846.778285] [<ffffffbffc1c0ed4>] wmi_event_worker+0x230/0x2f8 [wil6210] [89846.784865] [<ffffffc0000b0bc8>] process_one_work+0x278/0x3fc [89846.790591] [<ffffffc0000b1218>] worker_thread+0x200/0x330 [89846.796060] [<ffffffc0000b6664>] kthread+0xac/0xb8 [89846.800836] Code: b940c661 f9406a62 8b010041 f9400026 (f8636882) [89846.807008] ---[ end trace d6fdc17cd27d18f6 ]--- Reason is the following: when removing Rx vring (wil_netdev_ops.ndo_stop -> wil_stop -> wil_down -> __wil_down -> wil_rx_fini), Rx interrupt occurs. It trigger Rx NAPI, calling wil_rx_handle() that reaps (already cleaned) buffer, causing skb referring to garbage memory being set into reorder buffer. Then, network stack trying to access this buffer and fails. Prevent Rx NAPI from being scheduled if device going to stop. Bit wil_status_napi_en reflects NAPI enablement state, check it when triggering Rx NAPI. Testing shows that check for wil_status_napi_en sometimes gets negative, and new error message get printed - in this case kernel oops would be observed. Original oops is no more reproducible. This change requires also changes in the AP flows. Properly enable/disable NAPI for the AP. Make sure Rx VRING is disabled when resetting target. For this, promote __wil_up() and __wil_down() to the module scope, and use it in the relevant flows. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11wil6210: rename [en|dis]able irq to [un]maskVladimir Kondratiev
To better reflect real action performed, rename: s/wil6210_disable_irq/wil_mask_irq/ s/wil6210_enable_irq/wil_unmask_irq/ Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11wil6210: fix typo in commentVladimir Kondratiev
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11wil6210: fix for memory corruption while insmodDedy Lansky
After setting interrupt handler, driver enabled interrupts. This caused stale (old) HW interrupts to fire before driver is fully initialized. The fix is to enable interrupts only when driver is fully initialized and after FW/HW reset (to prevent any stale interrupts) Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11wil6210: add more debug printoutsVladimir Kondratiev
added misc printouts in some init/uninit functions for better traceability Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-09-11wil6210: firmware downloadVladimir Kondratiev
Firmware download implemented but is still experimental feature; flag controlling it added, no_fw_load. It is true by default, use no_fw_load=N to activate feature. Reset flows also got some adjustment for the fw download to work Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-08-25wil6210: update copyright year 2014Vladimir Kondratiev
Fix Copyright headers in all files changed in 2014, to mention 2014 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-06-19wil6210: interrupt statisticsVladimir Kondratiev
Track number of interrupts and Tx/Rx packets; expose through debugfs 'info'. Reset upon read. Used to analyse effectivness of interrupt coalescing and NAPI. Read twice with some interval like cat info > /dev/null; sleep 1; cat info Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-06-19wil6210: print error when notifying about FW errorVladimir Kondratiev
Print to dmesg when FW error notification is about to be sent Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-04-22wil6210: fix printouts for better readabilityVladimir Kondratiev
Reshuffle prints to consolidate firmware/hardware information report upon card init Convert print for unhandled MISC ISR bits to "debug" - it is normal situation and not an "error" Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fw error recoveryVladimir Kondratiev
upon fw error interrupt - in STA mode, disconnect/cancel scan and then reset FW/HW added module param - no_fw_recovery which is false by default Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: Fix kernel oops in reset flowVladimir Kondratiev
wil_reset() removes vring's At the same time NAPI may be active performing Rx/Tx completion. If this happens, Rx/Tx polling functions going to access already removed vrings Make sure NAPI is idle and won't be started prior to vring removal. For this, track NAPI enabled state Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-03-17wil6210: fix for HW bug in interrupt setup logicVladimir Kondratiev
Hardware bug triggered by the MSI init while INTx asserted for some reason. De-assert INTx prior to MSI set-up Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-01-09wil6210: interrupt moderationVladimir Kondratiev
Use hardware capabilities to limit IRQ generation to about 15 per msec It corresponds to about 7 packets/IRQ when running iperf with default parameters at 1.3Gbps Do not enable this feature in the sniffer (monitor) mode, because interrupt moderation cause timestamp accuracy deterioration. For the sniffer flow, it is important to get precise timestamp. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-22wil6210: use NAPIVladimir Kondratiev
Introduce NAPI for Rx and Tx completion. This fixes packet reordering that happens when Rx handled right in the IRQ: netif_rx puts packet in 'percpu' queue, then network stack fetches packets from 'percpu' queues for processing, with different pattern of queue switching. As result, network stack see packets in different order. This causes hard to understand TCP throughput degradation in about 30min Complete polling if only one packet was processed - this eliminates empty polls that would be otherwise done at the end of each burst Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-05-22wil6210: trace supportVladimir Kondratiev
Trace the following: - WMI cmd/event - log events - interrupts - Tx/Rx Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: new SW resetVladimir Kondratiev
New firmware allows for shorter SW reset procedure. After SW reset, FW raises "fw done" IRQ, at this moment mailbox control structures are initialized, driver caches it. New status bit wil_status_reset_done introduced to track completion of the reset. It is set by "fw ready" irq, and required for WMI rx flow to access control structures. WMI Tx flow protected by other status bit, wil_status_fwready. It can't be set before wil_status_reset_done is set by design. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-03-13wil6210: fix FW error notificationVladimir Kondratiev
user space get notified through kobject_uevent_env(), that might sleep and thus should run in thread context. Move user space notification to the thread handler, while mark FW is non-functional right in the hard IRQ. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: checkpatch warningsVladimir Kondratiev
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: fix checkpatch CamelCase warningsVladimir Kondratiev
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: rearrange IRQ debug printingVladimir Kondratiev
Make printings from IRQ appears in dmesg in chronological order Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-30wil6210: Detect FW errorVladimir Kondratiev
In the firmware, added is ability to report internal errors using IRQ. Catch this IRQ and notify user space via netlink User space get notified like (udevadm monitor --kernel --property): KERNEL[12660.320520] change /devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 (net) ACTION=change DEVPATH=/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 DEVTYPE=wlan EVENT=FW_ERROR IFINDEX=6 INTERFACE=wlan12 SEQNUM=2489 SOURCE=wil6210 SUBSYSTEM=net Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2013-01-04wireless: add new wil6210 802.11ad 60GHz driverVladimir Kondratiev
This adds support for the 60 GHz 802.11ad Wilocity card through a new driver, wil6210. Wilocity implemented the firmware, QCA maintains the device driver. Currently supported: - STA: with security - AP: limited to 1 connected STA, security disabled - Monitor: due to a hardware/firmware limitation either control or non-control frames are monitored Using a STA and AP with this drive, one can assemble a fully functional BSS. Throughput of 1.2Gbps is achieved with iperf. The wil6210 cards have on-board flash memory for the firmware, the cards comes pre-flashed and no firmware download is required. For more details see: http://wireless.kernel.org/en/users/Drivers/wil6210 Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-04-03 00:06:52 +0000