| Age | Commit message (Collapse) | Author |
|---|
|
the check of the return code is missing, user space does not get notified
about the error condition:
omapdss OVERLAY error: overlay 2 horizontally not inside the display area (403 + 800 >= 800)
omapdss APPLY error: failed to apply settings: illegal configuration.
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add support for DRA7xx DPI output.
DRA7xx has three DPI outputs, each of which gets its input from a DISPC
channel. However, DRA72x has only one video PLL, and DRA74x has two
video PLLs. In both cases the video PLLs need to be shared between
multiple outputs. The driver doesn't handle this at the moment.
Also, DRA7xx requires configuring CONTROL module bits to route the clock
from the PLL to the used DISPC channel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add support for DRA7xx to the HDMI driver.
The HDMI block on DRA7xx is the same as on OMAP5, except we need to
enable and disable the HDMI PLL via the CONTROL module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
On DRA7xx, DISPC needs to write output signal polarities not only to a
DISPC register, like for all earlier DSS versions, but to control
module's CTRL_CORE_SMA_SW_1 register.
This patch adds support to write the polarities to control module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add DRA7xx support to DISPC driver. The DISPC block is the same as on
OMAP5, except the PLL's used for clocking are "videoX", not "dsiX".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DRA7xx SoCs have one (DRA72x) or two (DRA74x) video PLLs. They are
basically the same as DSI PLLs on OMAPs, but without the rest of the DSI
hardware. The video PLLs also require some configuration via the CONTROL
module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add functions which configure the control module register
CTRL_CORE_DSS_PLL_CONTROL found in DRA7xx SoCs. This register configures
whether the PLL registers are accessed internally by DSS, or externally
using OCP2SCP interface. They also configure muxes which route the PLL
output to a particular LCD overlay manager within DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add base support for DRA7xx to DSS core.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
A race issue has been observed with the encoder-tpd12s015 driver, which
leads to errors when trying to read EDID. This has only now been
observed, as OMAP4 and OMAP5 boards used SoC's GPIOs for LS_OE GPIO. On
dra7-evm boards, the LS_OE is behind a i2c controlled GPIO expander,
which increases the time to set the LS_OE.
This patch simplifies the handling of the LS_OE gpio in the driver by
removing the interrupt handling totally. The only time we actually need
to enable LS_OE is when we are reading the EDID, and thus we can just
set and clear the LS_OE gpio inside the read_edid() function.
This also has the additional benefit of very slightly decreasing the
power consumption.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The OMAP5 HW supports directing DIGIT channel to DPI output, but the
driver doesn't support that. However, we have marked that configuration
as possible in the dss features, so in certain cases the driver tries to
use that configuration, leading to broken display.
Fix the problem by allowing DIGIT channel to go only to HDMI output.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The port arrays are constant data, so set them as 'const'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add a helper function to wait until the PLL's reset is done.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
In some cases we need global identifiers for the DSS PLLs, for example
when configuring clock muxing on DRA7. For this purpose let's add a
'enum dss_pll_id'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Assigning ddata->invert_polarity to itself is not very useful; the
context suggests that the right-hand side should have been
pdata->invert_polarity.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
opa362 is amplifier for video and can be connected to the tvout pads
of the OMAP3. It has one gpio control for enable/disable of the output
(high impedance).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
After the commit ef691ff48bc8 (OMAPDSS: DT: Get source endpoint by
matching reg-id) we look for the SDI output using the port number.
However, the SDI driver doesn't set the port number, which causes the
SDI display to not initialize.
Fix this by setting the SDI port number to 1. We use a hardcoded value,
as SDI was used only on OMAP3 and it's always port number 1 there.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The regulator_disable() doesn't accept NULL pointers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
HDMI hardware parameters structs for OMAP4 and OMAP5 contained two
initializers for 'clkdco_max'. The first one was a remnant with wrong
value.
Remove the extra initializer entries.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
Merge fbdev topic branches.
|
|
"i2c_put_adapter"
The i2c_put_adapter() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The bit field for IEC958_AES2_CON_SOURCE is bits 3-0 in
HDMI_CORE_FC_AUDSCHNLS2, not imaginary bits 3-4 (reverse order).
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Remove __exit qualifier from hdmi_uninit_output() because it is used
also in omapdss_hdmihw_probe().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Enabling idle mode during audio playback causes the glitches on OMAP5
HDMI. The TRM also suggests to use no-idle for HDMI audio playback.
This patch sets HDMI idle mode to no-idle for the duration of the
playback, and restores it back to original value afterwards.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
In new model these callbacks are obsolete since the ASoC component
drivers are integrated into the HDMI drivers and no callbacks are
needed anymore.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Removes the OMAP5 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Removes the OMAP4 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Make hdmi_mode_has_audio() more user friedly by taking hdmi_config as
parameter.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The booleans are not used anymore. Just select SND_OMAP_SOC_HDMI_AUDIO
to enable OMAP HDMI audio support.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Adds display_enabled flag and audio_abort_cb callback to struct hdmi.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This is used to store omap-hdmi-audio pdev for unregistering it.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Unify the private anonymous struct in hdmi4.c and hdmi5.c, name it as
struct omap_hdmi, and make it public in hdmi.h.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The audio dma port is found in the hdmi_wp physical address space.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
hdmi4_audio_get_dma_port() is unused and and broken.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
It does not waste too many bytes to compile all audio related core
functions always in with HDMI support. It should help readability and
in keeping the audio code in working shape. Leave the options just for
disabling and enabling the functionality in hdmi[45].c.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The OMAP5 HDMI audio implementation needs HDMI_AUDIO_LAYOUT_6CH in
hdmi_core_audio_layout enum. I found the correct value from ti-linux
3.8 tree.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The hdmi_wp_audio_config_format() expects sample_order of struct
hdmi_audio_format to be initialized. The only allowed value is
HDMI_AUDIO_SAMPLE_LEFT_FIRST.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Only OMAP4 DSS has non reserved bits above 6th bit in HDMI_WP_AUDIO_CFG.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Now that the DSS has the common DSS PLL, we no longer use the DSI PLL
feature flags from dss_features.c.
Remove all the unused feature flags.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Now that we have the common DSS PLL support, change HDMI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.
The function to program the PLL settings can be removed from hdmi_pll.c,
as the common PLL API contains the same functionality.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
hdmi_pll_enable powers off the PLL as the first thing it does. Right
after that, it enables the PLL powers.
The initial power-off is pointless, so let's remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
At the moment we have one function, hdmi_pll_enable, which enables the
PLL and writes the PLL configuration to registers.
To make the HDMI PLL ahere to the DSS PLL API, split the hdmi_pll_enable
into two parts: hdmi_pll_enable which enables the PLL HW, and
hdmi_pll_set_config which writes the config.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
HDMI PLL code needs the pointer to the WP block so that it can manage
its power. Currently this is passed as a function parameter to
hdmi_pll_enable and hdmi_pll_disable. To make the PLL function adhere to
the DSS PLL API, we need to remove the WP parameter.
This patch stores the WP pointer to hdmi_pll_data in hdmi_pll_init, so
that it's available when needed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The SYSRESET bits in HDMI PLL do not reset the PLL itself, but only
affect the power used for the PLL.
Afaik there is no reason to use the SYSRESET bits, and we don't use it
in the other PLLs, so let's remove the HDMI PLL reset to make the PLL
code simpler and similar to other PLLs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The code calculating HDMI PLL parameters has always been very confusing.
Now that we are implementing a common PLL library for the DSS, it's
important that the PLL code is understandable.
This patch rewrites the calculation code, and removes a few hacks that
were used there.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
We don't support interlace modes properly on OMAP5+ HDMI, so we need to
reject interlace timings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Only OMAP5+ has REFSEL field, but at the moment it's set also on OMAP4.
Fix this by adding a "has_refsel" field, and setting the REFSEL based on
that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Now that we have the common DSS PLL support, change DSI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.
The functions to calculate and program the PLL settings can be removed
from dsi.c, as the common PLL API contains the same functionality.
We also need to create struct dss_pll_hw entries for PLL hardware
features for different OMAP platforms, instead of using the
dss_features.c as the old code does.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
