blob: 0b5136e334b599c382fc6bbe2f7245e8abe128aa (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
|
/*
* Blackfin On-Chip SPI Driver
*
* Copyright 2004-2008 Analog Devices Inc.
*
* Licensed under the GPL-2 or later.
*/
#ifndef _SPI_CHANNEL_H_
#define _SPI_CHANNEL_H_
#define MIN_SPI_BAUD_VAL 2
#define BIT_CTL_ENABLE 0x4000
#define BIT_CTL_OPENDRAIN 0x2000
#define BIT_CTL_MASTER 0x1000
#define BIT_CTL_CPOL 0x0800
#define BIT_CTL_CPHA 0x0400
#define BIT_CTL_LSBF 0x0200
#define BIT_CTL_WORDSIZE 0x0100
#define BIT_CTL_EMISO 0x0020
#define BIT_CTL_PSSE 0x0010
#define BIT_CTL_GM 0x0008
#define BIT_CTL_SZ 0x0004
#define BIT_CTL_RXMOD 0x0000
#define BIT_CTL_TXMOD 0x0001
#define BIT_CTL_TIMOD_DMA_TX 0x0003
#define BIT_CTL_TIMOD_DMA_RX 0x0002
#define BIT_CTL_SENDOPT 0x0004
#define BIT_CTL_TIMOD 0x0003
#define BIT_STAT_SPIF 0x0001
#define BIT_STAT_MODF 0x0002
#define BIT_STAT_TXE 0x0004
#define BIT_STAT_TXS 0x0008
#define BIT_STAT_RBSY 0x0010
#define BIT_STAT_RXS 0x0020
#define BIT_STAT_TXCOL 0x0040
#define BIT_STAT_CLR 0xFFFF
#define BIT_STU_SENDOVER 0x0001
#define BIT_STU_RECVFULL 0x0020
/*
* All Blackfin system MMRs are padded to 32bits even if the register
* itself is only 16bits. So use a helper macro to streamline this.
*/
#define __BFP(m) u16 m; u16 __pad_##m
/*
* bfin spi registers layout
*/
struct bfin_spi_regs {
__BFP(ctl);
__BFP(flg);
__BFP(stat);
__BFP(tdbr);
__BFP(rdbr);
__BFP(baud);
__BFP(shadow);
};
#define MAX_CTRL_CS 8 /* cs in spi controller */
/* device.platform_data for SSP controller devices */
struct bfin5xx_spi_master {
u16 num_chipselect;
u8 enable_dma;
u16 pin_req[7];
};
/* spi_board_info.controller_data for SPI slave devices,
* copied to spi_device.platform_data ... mostly for dma tuning
*/
struct bfin5xx_spi_chip {
u16 ctl_reg;
u8 enable_dma;
u8 bits_per_word;
u16 cs_chg_udelay; /* Some devices require 16-bit delays */
/* Value to send if no TX value is supplied, usually 0x0 or 0xFFFF */
u16 idle_tx_val;
u8 pio_interrupt; /* Enable spi data irq */
};
#endif /* _SPI_CHANNEL_H_ */
|
